한국신재생에너지학회:학술대회논문집
Korean Society for New and Renewable Energy (KSNRE)
- Semi Annual
Domain
- Energy/Resources > New and Renewable Energy
2007.11a
-
Graphite/polymer composite bipolar plates for PEMFC are successfully developed, and their typical properties are superior to commercially available ones. Thermal property of the developed bipolar plate was evaluated by dynamic mechanical analyzer, and the results were compared to commercial ones. The specimens were immersed into the deionized water bath at
$80^{\circ}C$ for 1500hrs to evaluate dimensional stability and durability. Dimension, weight of the specimens as well as extraction conductivity was measured as each 500hrs. Fully molded bipolar plates without any machining or milling were also prepared using a specially developed mold, and they were applied to the fuel cell performance test. Results were compared to the machined commercial bipolar plate. -
SOFC 스택 밀봉재로서
$SiO_2-R_2O_3$ 계를 선정하여$R_2O_3$ 와 RO를 변화 하였을 때 유리 전이 온도, 열팽창계수, 이종 물질간의 젖음성, 환원 가스에 반응성 등을 조사하였다. 또한 모유리에 filler를 넣었을 때 filler 첨가에 따른 특성을 조사한 결과$B_2O_3/SiO_2$ 함량비 증가에 따라 열팽창계수는 증가하였고 전이점은 낮아졌으며 밀봉재를 이용한 SUS 와 SUS를$800^{\circ}C$ 접합 후 산화${\cdot}$ 환원분위기에서 작동했을 때. 화학적 반응 및 확산 반응층은 관찰되지 않았다. -
A dynamic model of proton exchange membrane fuel cell(PEMFC) system is designed to understand the performance of the PEMFC in residential power generator(RPG) over various balance of plant(BOP) options. In particular, since the performance of PEMFC system should be optimized for given operating ranges, it is necessary to design suitable BDP components which can support the operating ranges. The objective of this study is to develop a dynamic system model for the study of PEMFC performance over various BOP options. Therefore, a dynamic model is composed of a PEMFC stack model, a water management system model, a thermal management system model and a fuel/air supply model and the model is integrated under SIMULINK(R)environment. Basic simulation results will be presented.
-
Solid oxide fuel cells are clean, pollution-free technology for the electrochemical generation of electricity at high efficiency. Specially, the polarization resistance between electrolyte and electrode of SOFC unit cell is of importance, because it is desirable to develop SOFC operating at intermediate temperature below
$800^{\circ}C$ . The LSCF cathode prepared using modified oxalate method was investigated with different electrolyte. A precursor was prepared with oxalic acid, ethanol and$NH_4OH$ solution. The LSCF precursor was prepared at$80^{\circ}C$ , and pH control was 2, 6, 8, 9 and 10. The precursor powder was calcined at$800^{\circ}C$ ,$1000^{\circ}C$ and$1200^{\circ}C$ for 4hrs. The crystal of LSCF powders show single phase at pH 2, 6, 8 and 9, and the average particle size was about$3{\mu}m$ . The LSCF cathode with heat treatment at$1200^{\circ}C$ showed a plot of electric conductivity versus temperature. Unit cell prepared from the LSCF cathode, buffer layer between cathode and electrolyte and the LSGM, YSZ, ScSZ and CeSZ electrolyte. Also interface reaction between LSCF, buffer layer and electrolyte were measured by EPMA and the polarization resistance for unit cell with cycle measure using a Solatron 1260 analyzer. -
Shin, Jang-Sik;Shin, Seock-Jae;Lee, Seung-Young;Yang, Hye-Kyong;Sung, Bong-Hyun;Kim, Doo-Hoon;Park, Jong-Won 19
In this study, we investigated operating characteristics of natural gas fuel processor for polymer electrolyte membrane fuel cells (PEMFCs). The fuel processor consists of a natural gas reformer, a water-gas shift reactor, a heat-exchanger and a burner, in which the overall integrated volume is exactly(exceptionally) small, namely, about 10L except outer insulation. The producted hydrogen is$1Nm^3/hr$ and the maximum thermal efficiency is${\sim}76%$ (low heating value) at full operating load. A compact and highly efficient$1Nm^3/hr$ class natural gas fuel processor was developed at UNISON is an advantage for application in residential PEMFCs co-generation systems. -
Liquid water in flow channel is an important factor that limits the steady and transient performance of PEM fuel cells. A computational fluid dynamics study based on the volume-of-fluid (VOF) multi-phase model is conducted to understand the transport behavior of liquid water in flow channel. The liquid water transport in
$180^{\circ}$ bends is investigated and the effect of chamfering is discussed. The effect of wall adhesion is also considered by varying the contact angle of channel surfaces. The result of this study is believed to provide a useful guideline for design optimization of flow patterns or channel configurations of PEM fuel cells. -
This study considers the feasibility of the concentration control of the methanol solution by oscillating flow in the anode channel of passive type Direct Methanol Fuel Cells(DMFC). DMFC stack performance is largely influenced by the fuel concentration. If the fuel concentration is either lower than 0.5M or more than 2M, its performance deteriorates seriously because of the fuel starvation or the fuel crossover. In this respect the optimization of the fuel concentration is crucially important to maximize the DMFC stack performance. In this work, the effects of oscillating actuation in the fuel supply are studied to control the fuel concentration. Two important nondimensional parameters are introduced, each of which represents either the oscillating frequency or the oscillating amplitude. It is shown how these factors affect the stack performance and the efficiency of the DMFC stack.
-
Fuel cell with high electric efficiency has many probabilities of commercial use. Especially, polymer electrolyte or proton exchange membrane fuel cell (PEMFC) which is a low operating temperature and has less influence on
$CO_2$ concentration is considered the power generation system of small building and household. We calculated the optimal operational plans of 1 kW household PEMFC power system based on daily electric and heat demand patterns of various size of apartments. Calculated results show that the economic feasibility of PEMFC power system is very sensitive to the cost policy of electricity and natural gas. -
The comparisons between measured performance of lab-scale PEMFC and calculation were conducted to understand the detail phenomena of PEMFC for the various inlet oxygen humidity of cathode side. Experiments were performed at
$65^{\circ}C$ operation temperature and different inlet humidity conditions such as 40%, 60% and 80%. We used the MEA manufactured by oneself which include$Nafion^{(R)}$ 112 membrane, Nafion solution 20%, and carbon paper(E-TEK). As a result of this experiment, cell performance was getting higher by increasing inlet humidity condition at cathode side because ion conductivity of electrolyte membrane is increased. A 3D CFD simulation model of PEMFC was developed using commercially available CFD code that is one of the STAR-CD module, es-pemfc under same operating conditions. Model calculations results were compared with experimental ones on the polarization curves and calculation results are in good agreement with the experimental ones. Local water distribution and current density inside PEMFC are discussed in detail. -
Hydrogen fuel cell is clean and efficient technology along with high energy densities. While there are many different types of fuel cells, the proton exchange membrane fuel cell stands out as one of the most promising for transportation and small stationary applications. This paper focuses on design of bipolar plate for proton exchange membrane fuel cell. The bipolar plate model is realistically and accurately simulated velocity distribution, current density distribution and its effect on the PEMFC system using CFD tool FLUENT.
-
To find out the optimum design of hydrogen storage and supply tank using Metal Hydride (briefly MH) and to make clear the performance characteristics under various conditions are our research purpose. In order to use the low-temperature exhaust heat,
$LaNi_{4.7}Al_{0.3}$ which operates under the low pressure of 1MPa is chosen, and we measure the basic properties, namely density, specific heat, PCT(Pressure-Concentration-Temperature) characteristic, and effective thermal conductivity. Then, a numerical calculation model of hydrogen storage using MH alloy is suggested and this thermal diffusion equation of model is solved by the backward difference method. This calculation results rate compared with the experimental results of the systems which installed 1kg MH alloy and, it is found out that our calculation model can well predict the experimental results. By the experimental using MH alloy, it is recognized that the hydrogen flow rate can control by the step adjustment of brine temperature. -
The present paper reports the life time prediction of Acrylonitrile-Butadiene rubber (NBR) fuel cell gasket materials as a function of operational variables like acid concentration, ageing time and temperature. Both material and accelerated acid-heat aging tests were carried out to predict the useful life of the NBR rubber gasket for use as a fuel cell stack. The acid ageing of the gasket compounds has been investigated at 120, 140 and
$160^{\circ}C$ , with aging times from 3 to 600 h and increasing acid ($H_2SO_4$ ) concentrations of 5, 6, 7 and 10 vol%. Material characteristics the gas compound such as cross-link density, tensile strength and elongation at break were studied. The hardness of the NBR rubber was found to decrease with decreasing acid concentration at both 120 and$140^{\circ}C$ , but at$160^{\circ}C$ interestingly the hardness of the NBR rubber increased abruptly in a very short time at different acid concentrations. The tensile strength and elongation at break were found to decrease with increase in both the acid concentrate ion & temperature. The life time of the compounds were evaluated using the Arrhenius equation. -
To check the feasibility of SMART (Steam Methane Advanced Reforming Technology)system, an experimental investigation was conducted. A fluidized bed reactor of diameter 0.052 m was operated cyclically up to the
$10^{th}$ cycle, alternating between reforming and regeneration conditions. FCR-4 catalyst was used as the reforming catalyst and calcined limestone (domestic, from Danyang) was used as the$CO_2$ absorbent. Hydrogen concentration of 98.2% on a dry basis was reached at$650^{\circ}C$ for the first cycle. This value is much higher than$H_2$ concentration of 73.6% in the reformer of conventional SMR (steam methane reforming) system. However, the hydrogen concentration decreased because the$CO_2$ capture capacity decreased as the number of cycles increased. -
연료전지는 수소를 이용하여 전기를 생산하는 발전 시스템으로 운전 중 수소 누출과 폭발의 위험성을 항상 수반하고 있다. 따라서 안전성의 확보를 위해 연료전지 시스템 내부에서 수소 누출 시 유e동 특성으로 인한 특정 부근 농도 정체와 환기의 영향을 파악하는 것이 필요하다. 실험 장치와 전산유체역학 프로그램을 사용하여 챔버 내 수소의 유통 특성과 환기구에 따른 환기의 영향을 확인하였다. 수소의 누출 속도와 양에 따라 유동장의 형태는 크게 변하였으며 환기구의 위치와 크기는 특정 부근의 농도정체와 챔버 내 전체적인 수소 농도에 영향을 미침으로서 안정성을 확보하는 중요한 인자임을 알 수 있었다. 예측 결과를 실제 실험 모델과 비교하여 그 타당성을 검토하였으며 차후 가정용 연료전지 모듈의 환기구 설계에 적용할 수 있다.
-
Reformers which produce hydrogen from natural gas are essential for the operation of residential PEM fuel cells. For this purpose, steam-methane reforming reactions with Ni catalysts is primarily utilized. Commercial Ni catalysts are generally made to have porous pellet shapes in which Ni catalyst particles are uniformly dispersed over Alumina support structures. This study numerically investigates the reduction of catalyst effectiveness due to the mass transport resistances posed by porous structures of spherical catalyst pellets. The multi-component diffusion through porous media and the accurate kinetics of reforming reaction is fully considered in the numerical model. The preliminary results on the variation of the effectiveness factor according to different operation conditions are presented, which is planned to be used to develop correlations in future studies.
-
Diesel autothermal reforming has several problems such as carbon deposition in reforming reactor, sulfur poisoning of catalyst, difficulty of aromatics decomposition and mixing problems of reactants(diesel, steam, oxygen). Severe carbon deposition causes the rapid performance degradation of reformer. Carbon deposition is formed from ethylene, carbon precursor. Ethylene was generated at the homogeneous reaction zone of the reactor entrance. This phenomenon is closely linked to the mixing of reactants. In this investigation, we try to minimize the ethylene generation at the reactor entrance atomization technique.
-
We have concentrated on the performance improvement of each part for durability, safety and cost of high pressure storage system for fuel cell vehicle so far. But for the mass production of fuel cell vehicle, it is necessary to evaluate durability and safety in system module. We built the standard to evaluate vibration and collision safety of high pressure storage system for fuel cell vehicle, and could verify reliability of high pressure storage system.
-
Seo, Yu-Taek;Seo, Dong-Ju;Roh, Hyun-Seog;Jeong, Un-Ho;Koo, Kee-Young;Jang, Won-Jin;Yoon, Wang-Lai 75
천연가스의 수증기 및 이산화탄소 복합 개질은 탄화수소화합물과 이산화탄소를 원료로 사용하여 수소를 생산하는 공정으로, 온실가스로 지목되고 있는 주요 화합물을 수소와 일산화탄소 혼합 가스로 전환시켜 합성 반응 또는 연료전지에 사용할 수 있도록 해준다. 본 연구에서는$MgAl_2O_4$ 를 지지체로 하는 니켈계 촉매를 제조하여 수증기 및 이산화탄소 복합 개질 반응에 사용하였으며, 기존의 수증기 개질촉매 적용 시 문제가 되었던 탄소 침적에 의한 촉매 비활성화를 피할 수 있었다. 개발된 촉매 레시피를 바탕으로 펠릿 촉매를 제조하여 0.1 bpd규모의 Fischer-Tropsch 합성 반응에 적용 가능한 튜브형 반응기에 적용하여 수증기 및 이산화탄소 복합 개질 반응을 실시하였으며, 반응기의 온도 구배, 가스 조성 변화를 관찰하였다. 반응 조건에 따른 촉매 및 반응기의 성능 최적화를 실시하여 최적 촉매 및 반응기 성능을 모색하고자 하였다. -
Ryi, Shin-Kun;Park, Jong-Soo;Kim, Sung-Hyun;Cho, Sung-Ho;Hwang, Kyung-Ran;Kim, Dong-Won;Moon, Jin-Wook 79
-
In order to characterize the catalytically active sites on carbon black, acetylene chemisorption had been examined recently at 773 and 873 K by using a pulse technique. As the inject ion was repeated at 773 K, the adsorbed amount gradually decreased and eventually the adsorption did not occur any more. At 873 K a constant amount of
$C_2H_2$ was consumed repeatedly after several injections. Good linear relationships were obtained between the methane decomposition rate at 1123 or 1173 K and the cumulative acetylene adsorption at 773 K or the constant acetylene consumption at 873 K. Reasonable models for the associative acetylene chemisorption at 773 K and the constant acetylene consumption at 873 K on the armchair face at the edges of graphene layers were proposed. The constant consumpt ion may be explained by the "$C_2H_2$ -addition-hydrogen- abstract ion (CAHA)" mechanism. -
-
고정층반응기에서 여러 가지 전이금속으로 치환된 하이드로탈사이트(
$[M_xMg_{6-x}Al_2(OH)_{16}(CO_3)^{2-}]{\cdot}H_2O;$ M: 전이금속(Ni, Mn, Co, Cu, Zn) x: 전이금속 치환비($x=0.5{\sim}6$ ))를 합성하고 이를 소성한 후 메탄의 부분산화 반응에 사용하였다. 반응 시 도입되는$CH_4/O_2$ 비는 2로 하고$VHSV=120,000cm^3/g$ h, 온도를$500^{\circ}C$ 부터$50^{\circ}C$ 간격으로 하여$800^{\circ}C$ 까지 수행하였다. 실험결과 다른 전이금속들 중에서 니켈로 치환된 촉매가 대체적으로 부분산화반응을 촉진시키는데 좋은 것으로 나타났으며, 실험 결과 니켈의 hydrotalcite 중의 치환비(x)에 따른 차이는 별로 없었다. -
Kwak, Jung-Hun;Lee, Sang-Yup;Kim, Mi-So;Nam, Suk-Woo;Lim, Tae-Hoon;Hong, Seong-Ahn;Yoon, Ki-June 89
Partail oxidation(POX) of n-butane was investigated in this research by employing ceria-promoted Ni/calcium hydroxyapatite catalysts ($Ce_xNi_{2.5}Ca_{10}(OH)_2(PO_4)_6$ ; x =$0.1{\sim}0.3$ ) which had recently been reported to exhibit good catalytic performance in POX of methane and propane. The experiments were carried out with changing ceria content,$O_2/n-C_4H_{10}$ ratio and temperature. As the$O_2/n-C_4H_{10}$ feed ratio increased up to 2.75, n-$C_4H_{10}$ conversion and$H_2$ yield increased and the selectivity of methane and other hydrocarbons decreased. But with$O_2/n-C_ 4H_{10}$ = 3.0,$n-C_4H_{10}$ conversion and$H_2$ yield decreased. This is considered due to that too much oxygen may inhibit the reduction of Ni or induce the oxidation of Ni, which results in poor catalytic activity. The optimum$O_2/n-C_4H_{10}$ ratio lay between 2.50 and 2.75.$Ce_{0.1}Ni_{2.5}Ca_{10}(OH)_2(PO_4)_6$ showed the highest$n-C_4H_{10}$ conversion and$H-2$ yield on the whole. In durability tests, higher hydrogen yield and better catalyst stability were obtained with the$O_2/n-C_4H_{10}$ ratio of 2.75 than with the ratio of 2.5. -
Catalytic activities of color and conductive carbon blacks in ethane decomposition for
$CO_2-free$ hydrogen production were investigated. The ethane decomposition was carried out in a conventional fixed bed reactor under atmospheric pressure at 973-1173 K for 2 hours. When the decomposition in the presence of carbon black was compared with the non-catalytic thermal decomposition, the former exhibited significantly higher ethane conversion, higher C(s) selectivity and lower ethylene selectivity with small increase of the methane selectivity, which resulted in higher hydrogen yield. This indicates that carbon black is catalytically effective for dehydrogenation of ethane as well as subsequent decomposition of ethylene. All the carbon blacks exhibited stable catalytic activity with time. In durability tests, fluffy N-330 and BP2000 maintained their activities for 36 hours. -
A fluidized bed reactor made of quartz with 0.055 m I.D. and 1.0 m in height was employed for the thermocatalytic decomposition of methane to produce
$CO_2$ - free hydrogen . The fluidized bed was proposed for the continuous withdraw of product carbons from the reactor. The methane decomposition rate with the carbon black N330 catalyst was quickly reached a quasi-steady state rate and remained for several hour. The methane and propane mixture decomposition reaction was carried out at the temperature range of 850 - 900$^{\circ}C$ , methane and propane mixture gas velocity of 1.0$U_{mf}$ ${\sim}$ 3.0$U_{mf}$ and the operating pressure of 1.0 atm. Effect of operating parameters such as reaction temperature, gas velocity on the reaction rates was investigated. The produced carbon by the methane decomposition was deposited on the surfaces of carbon catalysts and the morphology was observed by TEM image. -
700
$^{\circ}C$ 이상의 온도에서 실시되는 고온수전해는 다가오는 수소경제시대의 주요한 수소제조기 술로 주목되고 있다. 이 연구에서는 Ni보다 전기전도도가 우수하고 가격이 저렴한 Cu를 사용하여 고온수 전해 수소극용 Cu/YSZ 복합체를 기계적합금법에 의해 제조하여 미세구조를 관찰하였고 Cu/YSZ를 수소전극으로 한 반전지를 제조하여 수조제조 실험을 실시하였다. Cu/YSZ 복합체는 Cu와 YSZ를 6:4(vol%)의 조성비로 유성밀을 사용하여 400 rpm으로 24시간 동안 실시하여 제조하였다. 고에너지 볼밀 후 500 nm이하의 나노크기의 복합체가 제조되었으며 Cu입자에 YSZ가 고르게 분포되어 있었다. 수은압입법으로 측정한 기공률은 70%이고 기공크기는 평균 0.5${\mu}m$ 으로 미세한 기공으로 이루어져 있었다. 제조된 Cu/YSZ 복합체를 수소전극으로 한 반전지를 제조하여 수소제조 실험을 실시한 결과 Ni/YSZ 전극보다 수소제조 성능이 우수한 것으로 나타났다. Cu의 높은 열팽창계수와 낮은 녹는점을 보완하면 우수한 고온수전해용 전극재료로 사용될 것으로 판단된다. -
최근 세라믹 막은 우수한 화학적, 열적 안정성으로 기체 분리 공정에 각광을 받아왔다. 특히 혼합기체에서 고 순도의 수소를 분리해 내는 기술은 연료전지 공정에서 화학 에너지를 적기화학 에너지로 전환시키는데 중요한 역할을 차지한다. 본 연구에서는 MTES 템플레이팅 막을 이용하여 이 막 공정의 흡착 및 투과 특성을 규명하고, 이성분 혼합기체에서 고 순도의 수소를 추출해 낼 수 있는 최적 조건을 도출해 내었다. 또한, 기체 분리 거동을 살펴보기 위해 Gproms Simulator를 이용하였으며, 이때 기체상의 물질전달을 모사하기 위해 Dust Gas Model(DGM)을, 표면 확산 거동을 모사하기 위해 Generalized Stefan-Maxwell(GSM)식을 적용하였다. 이를 통해 평형론적 흡착 뿐 아니라 속도론적 흡착을 동시에 적용할 수 있게 하였다. MTES 템플레이팅 막의 흡착 및 분리능을 규명하기 위해 본 연구에서는 혼합기체의 투과, 분리 실험이 선행되었다. 실험 조건은 온도범위
$30{\sim}50$ $^{\circ}C$ , 압력범위$0{\sim}5$ atm에서 수행되었으며, 혼합기체는 2성분으로 수소 메탄, 수소-이산화탄소, 수소-질소로 기체의 구성비는 각각 50:50 이다. 본 연구를 통해 각 혼합 기체들이 정상상태에 도달하는 시간과 분리능을 계산해 내었으며, 이 분리능을 다시 온도와 압력에 따른 결과로 분석하여 어느 조건에서의 수소 분리도가 최고치를 보이는지를 규명했으며, 시뮬레이션과 비교, 대조하여 예측도를 검사하였다. -
유동층 반응기를 이용한 프로판의 촉매 분해는
$CO_2$ 를 방출하지 않고 수소를 생성하는 새로운 방식이다. 카본블랙을 이용한 프로판 분해는 메탄보다 상대적으로 분해가 잘되며, 같은 온도에서 전환률이 높기 때문에 수소 생성량이 더 많다. 촉매로 사용된 카본블랙은 반응 중 생성되는 탄소의 침적에도 불구하고 8시간 이상 촉매의 활성이 유지되어 전환율이 일정하게 유지되었다. 프로판 촉매 분해 실험은 상압에서 600${\sim}$ $800^{\circ}C$ 온도 변화 실험을 수행하였고, 가스 유속 변화는 2.0${\sim}$ $4.0U_mf$ 에서 실험 조건 변화에 따른 실험을 하였다. 온도, 유속 변화에 따른 생성 가스의 몰분율과 프로판 전환율을 분석하였다. 프로판 분해에 의해 생성된 기체는 수소뿐만 아니라 메탄, 에틸렌, 에탄, 프로필렌과 분해되지 않은 프로판이 배출되었다. 수소를 제외한 여타 가스들은 고온에서 실험을 할수록 몰비가 줄어들었다. 고온에서 프로판의 전환율과 수소 수득률이 증가하였다. 프로판 분해 실험 전후의 카본블랙 표면의 변화는 FE-TEM으로 관측하였다. -
Performance of a steam reformer can be improved by using a coaxial cylindrical reactor, because the design can enhance the heat transfer for the steam reforming reaction, which is the one of main rate-determining steps of overall reactions. The objective of this study is to investigate the coaxial cylindrical reactor numerically. Pseudo-homogeneous model and one medium approach are incorporated for the chemical reactions, and models are validated with experimental results. The catalyst of the coaxial cylindrical reactor is 67% for one of the cylindrical reactor, but fuel conversion of the coaxial cylindrical reactor is increased by 10%. Heat flux profiles are investigated by modified Nusselt number and heat flux which is transported from the product gas to the catalyst bed affecting performance of the steam reformer.
-
-
수소 스테이션의 수소분리정제를 위한 Compact 형 PSA를 연구하였다. 수소 스테이션의 공정과정 중에서 수소 분리를 위한 PSA 장치는 에너지효율면에서 장점을 가지고 있지만 부피가 커서 많은 부지를 차지하는 단점이 있다. 수소 PSA의 이러한 단점을 줄이기 위하여 하나의 흡착탑 안에 다른 흡착탑을 넣는 Dual bed 형태의 Compact형 수소 PSA공정을 연구하였다. Compact형 수소 PSA는 하나의 bed안에 다른 하나의 bed를 넣음으로써 시스템이 차지하는 부피를 줄이는 한편, inner bed와 outer bed사이의 열교환 효과가 나타나기 때문에 그 효율을 높일 수가 있다. Compact형 Dual bed는 활성탄으로 충진하였고 공급 기체로는 4성분 수소 혼합물 (
$H_2/CO/CH_4/CO_2$ , 69:2:3:26 vol.%)를 사용하였다. 흡착탑의 동특성을 알아보기 위하여 공급유량 7LPM, 흡착압력 9atm의 조건으로 파괴 실험을 수행하였다. 또한, Compact형 흡착탑의 열교환 효과가 PSA공정에 미치는 영향을 보고자 한 쪽 탑에서 흡착을 할 때, 다른 탑에서 탈착이 일어나는 실험을 하였다. 그리고 P/F ratio에 따라 Compact형 PSA 공정 실험을 하고 Compact형 흡착탑과 같은 부피의 일반 두 탑 PSA 공정을 시뮬레이션 값과 비교함으로써 Compact형 PSA의 성능을 알아 보았다. 그 결과 Dual bed PSA는 작은 부피를 차지하는 장점뿐만 아니라 열적 효과로 인하여 기존의 단일 흡착탑 PSA에 비하여 보다 높은 효율을 나타내면서 우수한 수소 분리 성능을 보여주었다. -
In these recent years, low cost and stable battery electrode materials have been studied for HV/HEV application. Spinel cathode material
$LiMn_2O_4$ is widely studied as a promising cathode material of lithium ion secondary batteries because of it is low cost, easily to be prepared and capable to be operated in high voltage range. In this study,$LiMn_2O_4$ was undergoing surface modification with spinel lithium titanium oxide by sol-gel method in order to enhance its capacity retention. Properties of both unmodified and surface-modified$LiMn_2O_4$ were characterized by XRD, SEM, particle size analyzer while their cycling performance was tested with charge and discharge tester. -
고분자 전해질 연료전지의 성능에 영향을 주는 많은 인자들 중에서도 촉매층의 조성과 구조의 최적화는 성능변화에 큰 요인으로 작용 된다. 촉매층내 반응 활성점인 삼상계면을 형성시키기 위해 함침하는 Nafion binder를 anode와 cathode의 두 전극에 이온당량(Equivalent weight, EW)이 동일하게 함침시켜 그 성능을 확인하였다. 그 결과를 토대로 anode와 cathode에 이온당량을 각기 다르게 하여 각각의 전극마다 이온당량이 미치는 영향에 대해서도 살펴보았다. Anode와 cathode의 이온당량을 동일하게 EW1100, EW1000, EW900으로 변화 시켜주었을 경우 이온당량의 물성치가 상대적으로 향상된 EW900의 단위 전지 성능이 가장 우수하였으며, 이온당량이 EW900이었을 때 최적의 Nafion binder 함침량은 EW1100의 Nafion binder 함침량과 동일하였다. Anode와 cathode에 함침하는 Nafion binder의 이온당량을 각각 EW1100과 EW900, EW900과 EW1100으로 MEA를 제조하여 전극에 따라 이용당량이 미치는 영향을 살펴보았다.
-
In this work, 3-dimensional, non-isothermal numerical simulation was performed to analyse the effects of contact resistance and electric conductivity of GDL on the fuel cell performance. For numerical simulation contact resistance of Carbon and Stainless steel was measured. The simulation results reveal that 10 times change of electric conductivity leads only 6.5% decrease of PEMFC performance. But stainless steel which has high contact resistance decrease fuel cell performance over 25% at a high current density region than carbon. This results show that suitable Surface treatment technology is needed for metal bipolar plate, especially stainless steel.
-
The startup behaviour of PEM fuel cells at subfreeze zero is one of the most challenging tasks to be solved before PEM fuel cell vehicle is commercialized. Automotive companies are trying to increase cold statup capability of fuel cell. In this study, we found out the design factor of the stack to increase cold startup capability using 4kW stack and then cold startup test was performed at the various shutdown condition and the various current. In order to test the cold startup possibility and capability in vehicle, we installed 80kW stack in the vehicle and this 80kW fuel cell vehicle was housed in an environmental chamber to investigate the characteristics of cold startup and driving. We found that it is possible for fuel cell vehicle with 80kW stack to self-heated cold startup and drive at
$-15^{\circ}C$ . -
-
Birnessite-type manganese dioxide(
$MnO_2$ ) was coated uniformly onto carbon nanotubes (CNTs) through a spontaneous direct redox reaction between CNTs and permanganate ions($MnO_4\;^-$ ). The initial specific capacitance of the$MnO_2/CNT$ nanocomposite in an organic electrolyte at a large current density of 1 A/g was 250 F/g, which is equivalent to 139 mAh/g based on the total weight of the electrode material including the electroactive material, conducting agent and binder. The specific capacitance of the$MnO_2$ in the$MnO_2/CNT$ nanocomposite was as high as 580 F/g (320 mAh/g), indicating excellent electrochemical utilization of the$MnO_2$ . The addition of CNTs as a conducting agent can improve the high rate capability of$MnO_2/CNT$ nanocomposite considerably. An analysis of the in-situ X-ray absorption near-edge structure (XANES) showed an improvement in the structural and electrochemical reversibility of the$MnO_2/CNT$ nanocomposite by heat-treatment. -
A serpentine channel geometry often used in a polymer electrolyte membrane fuel cell has a strong pressure gradient between adjacent channels in specific regions. The pressure gradient helps some amount of reactant gas penetrate through a gas diffusion layer(GDL). As a result, the overall serpentine flow structure is slightly different from intention of a designer. The purpose of this paper is to examine the effect of serpentine flow structure on current density distribution. By using a commercial code, STAR-CD, a numerical simulation is performed to analyze the fuel cell with relatively high aspect ratio active area. To increase the accuracy of the numerical simulation, GDL permeabilities are measured with various compression conditions. Three-dimensional flow field and current density distribution are calculated. For the verification of the numerical simulation results, water condensation process in the cathode channel is observed through a transparent bipolar plate. The result of this study shows that the region of relatively low current density corresponds to that of dropwise condensation in cathode channels.
-
Fuel cell electric vehicles (FCEVs) using hydrogen gas are zero emission vehicles, thus emission measurement for combustion vehicles is not applicable. The hydrogen gas consumption for fuel economy will be measured by the stabilized pressure/temperature method, mass flow method and electrical current method, etc. In this research, weight method with a newly manufactured test equipment is applied to measure the hydrogen consumption because above 3-methods have a deviation. The hydrogen consumption is directly calculated by the weight differences of the external hydrogen tank before and after the chassis dynamometer test. Ultimately the fuel economy for FCEVs is obtained with a deviation less than 1% in all chassis dynamometer tests.
-
Ejector system is a device to transport a low-pressure secondary flow by using a high-pressure primary flow. Ejector system is, in general, composed of a primary nozzle, a mixing section, a casing part for suction of secondary flow and a diffuser. It can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejector system is simple in construction and has no moving parts, so it can not only compress and transport a massive capacity of fluid without trouble, but also has little need for maintenance. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an applicable model and operating conditions for an ejector in the condition of sonic and subsonic, which can be extended to the hydrogen fuel cell vehicle. Experimental and theoretical investigation on the sonic and subsonic ejectors with a converging-diverging diffuser was carried out. Optimization technique and numerical simulation was adopted for an optimal geometry design and satisfying the required performance at design point of ejector for hydrogen recirculation. Also, some sonic and subsonic ejectors with the function of changing nozzle position were manufactured precisely and tested for the comparison with the calculation results.
-
연료전지의 상용화 시점에 이르러 내구성에 대한 기술 확보가 점점 더 부각되고 있다. 현재 연료전지의 내구성을 감소시키는 1차적인 요인은 핵심부품인 촉매, 전해질막, MEA(Membrane & Electrode Assembly) 등에 의한 것이며 2차적인 요인은 운전 시스템 및 환경 등에 의해 결정되어진다. 특히, 연료전지자동차는 이동용, 가정용, 발전용에 비하여 부하변동이 극심한 조건에서 운전되기 때문에 연료전지 시스템의 내구성 확보에 많은 제어기술이 요구된다. 본 연구에서는 연료전지자동차 운전조건(Driving mode)을 부하변동 기준에 의한 고전류, 중전류, 저전류의 3가지 모드로 분류하였다. 각각의 운전조건에서 일정 cycle마다 성능곡선을 측정하여 10만 cycle 이상의 반복운전을 수행하였으며 측정된 성능곡선을 empirical equation에 적용하여 시간에 따른 overvoltage 인자에 대한 분석을 하였다. 운전시간이 증가함에 따라 고전류 모드의 경우 activation overvoltage 인자 중 current density loss가 증가하여 OCV가 급격히 감소하였으나 내구성은 저전류 모드에 비하여 높게 나타났다. 저전류 모드의 경우 고전류 모드와 상반된 결과를 보였으며 성능감소요인은 activation 및 ohmic overvoltage의 점차적인 증가에 의한 것으로 분석되었다.
-
The objective of this study is to demonstrate and commercialized for on-board fuel storage system for the hydrogen fuel cell vehicles. Type3 composite cylinder is consisting of the full wrapped composites on a seamless aluminum liner. Especially, the seamless aluminum liner has been commercialized with development of fabrication through this study. The key technologies, including design, analysis and the optimized filament winding process for 350bar composite cylinder, were established and verified with design qualification test in accordance with international standard. And the facilities for fabrication and design qualification test have been constructed.
-
HEV용 리튬이온 전지에 대한 연구는 최근에 많은 연구가 진행되고 있으며 그중 고용량 및 저렴한 가격, 환경에 대한 안정성으로 인해 Li-Mn spinel에 대한 성능향상 연구가 많이 이루어지고 있다. 본 연구에서는 Li-Mn spinel의 입자크기에 대한 기초 물성 과 전기적 특성을 측정하여 입자크기가 용량에 미치는 영향에 대한 고찰을 하였다. Li-Mn spinel의 비표면적, C-V 특성, 전기적 용량, coulomb efficiency 등을 통하여 입자의 크기와 전해액, Li의 구동등과 관련하여 용량특성에 향상을 가져오는 입자크기 조건을 정의하였고 그에 따라 온도별로 합성 한 후 입자사이즈에 대한 특성을 나타내었다.
-
-
Because of accident or leak of electricity, high voltage electricity can be conducted to vehicle chassis and damage human. Therefore the unit for detecting ground fault is necessary to minimize loss of life or equipment damage. Isolation resistance must be monitored for detecting ground fault. GFD(Ground Fault Detection) unit continually generate the pulse voltage between high voltage network and chassis. This will be sensing the returned current, calculate the isolation resistance and make decision the ground fault. This paper describes the method detecting ground fault.
-
An object of the present study is to provide a hollow fiber membrane humidifier capable of improving the humidification efficiency while lowering the pressure loss, and is suitably usable for PEMFC(Polymer Electrolyte Membrane Fuel Cell). The performance of PEMFC is decisively dependent on the humidity of the electrolyte membrane(fluorinated membrane) and a humidifier plays an important role in moisturizing electrolyte membrane. Especially, this humidifier is a passive type(power-free) item and is volumetrically optimized. In this research, we propose the substitutes for the expensive fluorinated humidifier materials and the optimum dry-jet wet spinning conditions of hollow fiber membrane. In addition to that, This study will present an performance of an humidifier and compare computational results with the experimental data.
-
PEMFC의 상용화 진입에 있어서 걸림돌 중의 하나가 열화(degradation)에 의한 성능감소이다. PEMFC 고분자 막의 열화가 PEMFC 성능 감소에 많은 영향을 미친다. 고분자 막의 성능 감소 원인은 여러가지가 있지만 무가습/OCV조건에서 성능 감소가 잘 된다. 그 이유에 대해서는 OCV/무가습 조건에서 과산화수소나 라디칼이 많이 형성될 수 있다는 것과, OCV조건에서 사용되지 못하는 수소와 산소의 gas-crossover 가 많기 때문이라는 것 그리고 무가습 조건에서 수소와 산소의 분압이 높아 gas-crossover 가 유리하고 악의 건조에 따른 물리적인 영향 등등이 거론되고 있다. 본 연구에서는 같은 조건에서 Cell 운전온도가 막열화에 미치는 영향을 실험하였다. OCV 여려 조건 에서 단위전지 실험을 한 후 I-V, 수소 투과도, 임피던스, FER(fluoride emission rate)등을 측정해 그 결과를 검토 분석하였다. OCV/Anode 무가습 조건이 알려진 대로 막열화 가속조건 이었음을 확인하였고, 실험 결과 Cell 운전온도가
$10^{\circ}C$ 증가 할 때마다 FER(fluroide emission rate)이 즉 막 열화속도가 약 2배정도 증가함을 보였다. -
-
Hydrogen could be produced from any substance containing hydrogen atoms, such as water, hydrocarbon (HC) fuels, acids or bases. Hydrocarbon fuels couold be converted to hydrogen-rich gas through reforming process for hydrogen production. Even though fuel cell have high efficiency with pure hydrogen from gas tank, it is more beneficial to generate hydrogen from city gas (mainly methane) in residential application such as domestic or office environments. Thus hydrogen is generated by reforming process using hydrocarbon. Unfortunately, the reforming process for hydrogen production is accompanied with unavoidable impurities. Impurities such as CO,
$CO_2$ ,$H_2S$ ,$NH_3$ , and$CH_4$ in hydrogen could cause negative effects on fuel cell performance. Those effects are kinetic losses due to poisoning of electrode catalysts, ohmic losses due to proton conductivity reduction including membrane and catalyst ionomer layers, and mass transport losses due to degrading catalyst layer structure and hydrophobic property. Hydrogen produced from reformer eventually contains around 73% of$H_2$ , 20% or less of$CO_2$ , 5.8% of less of$N_2$ , or 2% less of$CH_4$ , and 10ppm or less of CO. Most impurities are removed using pressure swing adsorption (PSA) process to get high purity hydrogen. However, high purity hydrogen production requires high operation cost of reforming process. The effect of carbon dioxide on fuel cell performance was investigated in this experiment. The performance of PEM fuel cell was investigated using current vs. potential experiment, long run (10 hr) test, and electrochemical impedance measurement when the concentrations of carbon dioxide were 10%, 20% and 30%. Also, the concentration of impurity supplied to the fuel cell was verified by gas chromatography (GC). -
This paper shows the Development of In-tank pressure regulator and Solenoid Valve used in FCV(Fuel Cell Vehicle). We have developed new type of Regulator and Solenoid through analysis of the structure and characteristics of component of FCS(Fuel Cell System) from the advanced technology. Now it is possible to localize the component by making use of the development of Regulator and Solenoid made by us. Regulator and Solenoid is a equipment to control hydrogen pressure supplied into a stack. Therefore, outlet pressure, a flow of fluid and temperature are important parameters according to a inlet pressure. And leak test, endurance test and burst test should be done to guarantee the performance and safety of Regulator and Solenoid used in the fuel of high pressure. Also, Hydrogen friendly materials are applied to inner parts of the Regulator, Solenoid and weight reduction is done to cost saving in part not related to performance. As a result, we have proven the good performance and reliability in endurance of Regulator, Solenoid and will make an development in performance as well as durability to ensure industrialization.
-
-
We developed and tested the high pressure hydrogen gas cylinder(type4) for fuel cell vehicle. The working pressure is 350bar. We conducted material tests, production tests and design qualification tests on the developed cylinders according to modified NGV2-2000(hydrogen). The high pressure hydrogen gas cylinder met all the design qualification requirements of ANSI/CSA NGV2-2000 and acquired NGV2 certification from independent inspection agency.
-
Kim, Woo-June;Park, Chang-Ho;Jee, Yong-Jun;Cho, Kyung-Seok;Kim, Young-Dae;Park, Se-Young;Oh, Chang-Hoon 197
FCEV uses electric energy generated from fuel cell stack, thus all consisting parts must be re-designed to be suitable for electricity based system. Cathode air blower which supplies compressed air into fuel cell stack has similar shape of turbocharger, but a radial turbine of traditional turbocharger is removed and high speed BLDC motor is installed . Generally, maximum 10% of electric power of fuel cell stack is consumed in air blower, therefore an effective design of air blower can improve the performance of FCEV directly. This study will present an aerodynamic design process of an air blower and compare computational results with experimental data. -
A novel self-humidifying composite membrane for the proton exchange membrane fuel cell (PEMFC) at low humidity condition was developed. The
$Pt/TiO_2 catalyst particles were synthesized via supercritical impregnation methods. Pt precursor was dissolved in supercritical carbon dioxide and impregnated onto$TiO_2$ particles. Pt precursors were platinum(II) acetylacetonate, Dimethyl(1,5-cyclooctadiene) platinum(II) and we controlled the ratio of Pt to$TiO_2$ The impregnated Pt precursor was converted to$TiO_2$ supported Pt nanoparticle under various reducing conditions.$TiO_2$ catalyst particles were dispersed uniformly into the Nafion solution, and then$Pt/TiO_2/Nafion$ composite membrane was prepared using solution-cast method. The size, dispersion and content of the platinum had been characterized with Transmission Electron Micrograph (TEM), X-ray diffract ion (XRD) and Inductively Coupled Plasma - Atomic Emission Spectrometer (ICP-AES). The cell performance with the self-humidifying composite membrane was compared with a recast Nafion membrane under both humidified and dry conditions at 65$^{\circ}C$ . -
We aim to develop antifreezing coolant used to in the 200kW Fuel Cell system that is possible to starting at low temperature and that must not to be freezed under
$-30^{\circ}C$ , have high coductivity, excellent system protection ability and durability. -
고분자전해질형 연료전지의 구조 및 구성품의 물성에 따른 성능 및 물이동 현상에 관해서 많은 연구가 진행되고 있다, 이들 연구는 대체적으로 연료 전지의 BOP(Balance of plant)를 포함하는 연료전지 시스템에 관한 연구 보다는 단위 전지 및 스택에 관한 연구에 국한되어 왔다. 연료전지의 시스템에 관한 연구들 또한 세부적인 연료전지 내부의 거동에 대해서는 고려하지 않고 있었다. 이는 연료전지의 상세 모델을 이용해 연료전지 시스템에 대해 접근하기 보다는 시스템의 성능 및 동특성에 대한 연구가 주를 이루었기 때문으로 생각된다. 본 연구에서는 연료전지 음극의 수소 배출가스를 재순환할 경우 연료전지 내부에서의 거동에 미치는 영향에 대해 2차원 정상상태 모델을 이용하여 분석해 보았다. 또한 재순환된 수소에 의한 연료전지 내부 거동의 변화 및 수소 이용율 상승 효과를 연료 전지 성능과 함께 비교해 보았다 이를 위해 2차원 정상상태 모델을 개발하였고 이를 실험을 통해 검증하는 작업을 수행하였다. 여기에 사용된 연료전지 모델은 Gore社 의
$PRIMea^{(R)}$ 을 사용한 연료전지의 성능을 잘 예측하고 내부의 유동 및 물이동 현상에 관한 정보를 제공한다. 이는 여러 하이브리드 자동차용 연료전지 시스템이 연료전지 배출가스의 재순환을 고려하고 있는 상황에서 연료전지 작동 조건의 최적화에 유용한 정보를 제공 할 수 있다는 의의를 가진다. -
PEMFC의 전기화학적 반응은 촉매, 이오노머, 기공이 만나는 삼상계면에서만 일어나므로, 전극 구조의 최적화가 성능 향상 및 장기안정성 확보에 있어 매우 중요하다. 본 연구에서는 전극 미세구조를 실시간으로 분석하기 위해 임피던스 복소캐패시턴스법을 도입하고자 하였다. 즉, PEMFC의 양극에 질소를 공급하면 0.4 V 부근에서 전기이중층 형성 반응만이 일어나는 것을 확인하였으며, 이때 음극에는 수소를 공급하여 기준전극 및 반대전극으로 사용하였다. 측정된 임피던스를 복소캐패시턴스로 변환하고 허수부를 주파수에 대해 도시하면 피크 형태의 곡선이 얻어지는데, (1) 피크 면적은 전극/전해질의 계면면적, (2) 피크 위치는 이오노머 네트워크에 의한 수소이온 전도 특성, (3) 피크 폭은 다공성 구조의 균일도를 각각 나타내므로, 피팅 없이 직접적인 해석이 가능하다는 장점을 가진다. 반면, 기존의 Nyquist 도시법은 피팅에 의한 분석이 필요하며, 전극층의 불균일한 구조로 인해 단순한 등가회로 구성이 어려운 문제점을 가진다. 최종적으로, MEA 제작 조건 및 운전 조건을 변수로 하여 임피던스를 측정하고 복소캐패시턴스 분석을 수행하여, 퇴화 경로를 규명하고 운전 조건을 최적화하고자 하였다.
-
The purpose of study is a development of the high reliance electric driven water-pump that fuction is forcing the movement of water using basic design, proto sample and test at the cooling system. It was important to supply a coolant quickly and accurately for the requirement of flow rate at the system when we carried out the designs for BLDC Motor, Controller and water pump(Impeller, Volute Casing, Sealing Device) First, we attained ours purpose that the target efficiency for water pump was over 40% and then we are doing the optimum design for Brushless Motor and Controller that its target is over 55% of efficiency.
-
Lim, Soo-Jin;Park, Gu-Gon;Park, Jin-Soo;Park, Seok-Hee;Yoon, Young-Gi;Lee, Won-Yong;Lee, Young-Moo;Kim, Chang-Soo 221
고분자전해질연료전지의 효율과 수명은 고분자 전해질 막과 밀접하게 관련되어있다. 연료전지 상용화를 위해 내구성과 안정성은 반드시 확보되어야 한다. 본 연구에서는 고분자전해질연료전지용 막전극접합체에 대해서 제작과정, 체결과정 및 운전 중에 발생할 수 있는 물리적 손상이 연료전지에 미치는 영향을 알아보고자 하였다. 실제 고분자전해질연료전지 조건에서 구멍이 생기는 경우를 모사하기 위해 막전극접합체에 다양한 크기 및 형상의 물리적 손상을 형성시켰다. 또한 여러 위치에서의 손상도 비교하였다. 손상시킨 막전극접합체에 대해 단위전지 성능평가와 순환전압전류 실험을 비교 분석하였다. 막전극접합체의 결함이 커질수록 수소기체투과도는 증가하고, OCV와 성능은 감소하였다. 또한 성능과 수소기체투과도는 서로 관련이 있음을 알 수 있었다. -
-
-
-
-
Oh, Byung-Du;Han, Il-Ki;Oh, Dae-Kon;Lee, Hae-Seok;Kim, Hyo-Jin;Lee, Jae-Jin;Kim, Seong-Il;Han, Won-Seok;Kang, Ho-Kwan 235
-
-
-
-
-
-
-
-
The application of photovoltaics into building as integrated building components has been paid more attention worldwide. Photovoltaics or solar electric modules are sol id state devices, directly converting solar radiation into electricity; the process does not require fuel and any moving parts, and produce no pollutants. And the prefab building method is very effective because the pre- manufactured building components is simply assembled to making up buildings in the construction fields especially the sandwich panel. So, this paper describes a design and performance test of the 10kW poly metal pv module(pmpp) system. It is concluded that the prediction of BIPV system's performance should be based on the more accurate PV module installation.
-
Active Frequency Drift Positive Feedback Method for Anti-islanding applied Digital Phase-Locked-LoopAs photovoltaic(PV) power generation systems become more common, it will be necessary to investigate islanding detection method for PV systems. Islanding of PV systems can cause a variety of problems and must be prevented. However, if the real and reactive powers of the load and PV system are closely matched, islanding detection by passive methods becomes difficult. Also, most active methods lose effectiveness when there are several PV systems feeding the same island. The active frequency drift positive feedback method(AFDPF) enables islanding detection by forcing the frequency of the voltage in the island to drift up or down. In this paper the research for the minimum value of chopping fraction gain applied digital phase-locked-loop (DPLL) to AFDPF considering output power quality and islanding prevention performance are performed by simulation and experiment according to IEEE Std 929-2000 islanding test.
-
In this paper, a PV multi-string PCS with a grid-connection is proposed. An improved MPPT algorithm for the PV multi-string PCS is suggested. Each PV string has its own MPP tracker and the proposed MPPT algorithm prevents LMPP tracking due to power ripple. In the PV PCS with single-phase inverter has a large current ripple at twice the grid frequency. The current ripple reduction algorithm without external component is suggested. Also, this paper proposes a simple control method to achieve sharing of the PV string voltage and current among the interleaved parallel boost converters. All algorithms and controllers are implemented on a single-chip microcontroller. Experimental results obtained on a 3kW prototype show high performance of the proposed PV multi-string PCS.
-
-
The importance of natural light in building is known by all of us who experienced dark rooms. The sunlight system is very important from energy saving and human welfare point of view. The system consists of light-collecting module, light -transporting module and light-emitting module. The light-collection is used light reflection mirror, a prism for lighting bent, and lens for light condensing. The transportation of collected sunlight is used polished duct, tube, pipe and specially used fiber optic cable. This paper investigate research and development trends of sunlight system for advanced product.
-
Investigation of surface texturing to reduce optical losses for multicrystalline silicon solar cellsIt is important to reduce optical losses from front surface reflection to improve the efficiency of crystalline silicon solar cells. Surface texturing by isotropic etching with acid solution based on HF and
$HNO_3$ is one of the promising methods that can reduce surface reflectance. Anisotropic texturing with alkali solution is not suitable for multicrystalline silicon wafers because of its various grain orientations. In this paper, we textured multicrystalline silicon wafers by simple wet chemical etching using acid solution to reduce front surface reflectance. After that, surface morphology of textured wafer was observed by Scanning Electron Microscope(SEM) and Atomic Force Microscope(AFM), surface reflectance was measured in wavelength from 400nm to 1000nm. We obtained 29.29% surface reflectance by isotropic texturing with acid solution in wavelength from 400nm to 1000nm for fabrication of multicrystalline silicon solar cells. -
Shur, Joong-Won;Hwang, Jung-Hoon;Kim, Youn-Jea;Moon, Sang-Jin;So, Won-Wook;Kim, Min-Soon;Gii, Jong-Won;Yoon, Dae-Ho 268
-
Kim, Min-Sik;Chalapathy, R.B.V.;Larina, L.;Shin, Dong-Hyeop;Yun, Jae-Ho;Yoon, Kyung-Hoon;Ahn, Byung-Tae 269
-
In this report, Indium-free and Indium-reduced thin film materials for solar absorber were studied in order to search alternative materials for thin film solar cell. The films of
$Cu_2ZnSnSe_4$ and$Cu_2ZnSnSe_2$ were deposited using mixed binary chalcogenides powders. From the film bulk analysis result, it is observed that Cu concentration is a function of substrate temperature as well as CuSe mole ratio in the target. Under optimized conditions,$Cu_2ZnSnSe_4$ and$Cu_2ZnSnSe_2$ thin films grow with strong (112), (220/204) and (312/116) reflections. Films are found to exhibit a high absorption coefficient of$10^4$ $cm^{-1}$ .$Cu_2ZnSnSe_4$ film shows a 1.5 eV band gap. On the other side, an increasing of optical band gap from 1.0 eV to 1.25 eV ($CuInSnSe_2$ ) is found to be proportional with an increasing of Zn concentration. All films have a p-type semiconductor characteristic with a carrier concentration in the order of$10^{14}$ $cm^{-3}$ , a mobility about$10^1$ $cm^{2{\cdot}-1.}S^{-1}$ and a resistivity at the range of$10^2-10^6$ ${\Omega}{\cdot}m$ . -
-
유리를 기판으로 하는 superstrate pin 비정질 태양전지에서 전면투명전도막(TCO)과 p-layer의 계면이 태양전지의 효율을 내는데 가장 큰 기여를 한다. 전면투명전도막(TCO)으로 현재 일반적으로 사용되는 ZnO:Al는
$SnO_2:F$ 보다 전기,광학적으로 우수하고, 안개율(Haze)높으며, 수소 플라즈마에서의 안정성이 높은 특정을 갖고 있다. 그래서 박막 태양전지 특성향상에 매우 유리하나, 태양전지로 제조했을 때,$SnO_2:F$ 보다 충진율(Fill factor:F.F)과V_{\infty}$ 가 감소한다는 단점을 가지고 있다. 본 실험실에서는$SnO_2:F$ 의 F.F가 72%이 나온 반면 ZnO:Al의 F.F은 68%에 그쳤다. 이들 원인을 분석하기 위해 TCO/p-layer의 전기적 특성을 알아 본 결과,$SnO_2:F$ 보다 ZnO:Al의 직렬저항이 높게 측정되었다. 이러한 결과를 바탕으로 p-layer 에 R={$H_2/SiH_4$ }=25로 변화, p${\mu$}c$ -Si:H/p a-SiC:H 로 p-layer 이중 증착, p-layer의 boron doping 농도를 증가시키는 실험을 하였다. 직렬저항이 가장 낮았던 p${\mu$}c$ -Si:H/p a-SiC:H 로 p-layer 이중 증착에서 Voc는 0.95V F.F는 70% 이상이 나왔다. 이들 각 p층의$E_a$ (Activation Energy)를 구해본 결과,${\mu$}c$ -Si:H의 Ea 가 가장 낮은 것을 관찰 할 수 있었다. -
a-Si:H/
${\mu}$ c-Si:H 적층형 태양전지의 효율향상을 위해 상부전지와 하부전지간의 접합특성은 매우 중요하다. 본 연구에서는, 접합특성을 향상하기 위하여 아몰퍼스 보다 전도도가 높은 마이크로화된 n층 또는 ZnO:Al을 중간층으로 삽입한 태양전지를 제조하였으며, 그 특성을 전기적, 광학적 방법으로 분석하였다. 전기적 특성에서, 상부전지 n층에 아몰퍼스를 적용한 태양전지의 경우, 상부전지와 하부전지 간의 직렬저항이$500{\Omega}-cm^2$ 이상으로 높게 측정되었고, 이에 따라 AM 1.5 상태의 I-V 특성에서 비틀림 현상이 발생하여 곡선인자(Fill Factor : FF)가 낮게 측정되었다. 이에 반하여, 상부전지 n층에 마이크로층을 적용하거나, ZnO:Al 중간층을 삽입한 시편의 경우, 상부전지와 하부전지간의 직렬저항이$1{\Omega}-cm^2$ 이하로 감소하였으며, 이와 같은 계면간의 접합특성 향상으로 I-V특성에서 비틀림 현상이 사라지고, FF가 70% 까지 증가하였다. 또한, 마이크로층과 ZnO:Al 중간층을 동시에 적용한 태양전지의 경우, FF가 75%까지 가장 높게 증가하였다. 광학적 특성의 경우, 같은 두께의 아몰퍼스 n층에 비하여 마이크로 n층이 투과도는 더 높게, 반사도는 낮게 측정되었으며, 이는 하부전지의 단락전류 (Short circuit current : Jsc)를 높여줄 것으로 판단된다. -
Recently, we have developed p-i-n a-Si:H single junction thin film solar cells with RF (13.56MHz) plasma enhanced chemical vapor deposition (PECVD) system, and also successfully fabricated the mini modules (
$ > 300cm^2$ ), using the laser patterning technique to form an integrated series connection. The efficiency of a mini module was 7.4% ($Area=305cm^2$ , Isc=0.25A, Voc=14.74V, FF=62%). To fabricate large area modules, it is important to optimise the integrated series connection, without damaging the cell. We have newly installed the laser patterning equipment that consists of two different lasers,$SHG-YVO_4$ (${\lambda}=0.532{\mu}m$ ) and YAG (${\lambda}=1.064{\mu}m$ ). The mini-modules are formed through several scribed lines such as pattern-l (front TCO), pattern-2 (PV layers) and pattern-3 (BR/back contact). However, in the case of pattern-3, a high-energy part of laser shot damaged the textured surface of the front TCO, so that the resistance between the each cells decreases due to an incomplete isolation. In this study, the re-deposition of SnOx from the front TCO, Zn (BR layer) and Al (back contact) on the sidewalls of pattern-3 scribed lines was observed. Moreover, re-crystallization of a-Si:H layers due to thermal damage by laser patterning was evaluated. These cause an increase of a leakage current, result in a low efficiency of module. To optimize a-Si:H single junction thin film modules, a laser beam profile was changed, and its effect on isolation of scribed lines is discussed in this paper. -
박막형 태양전지 및 플렉서블 태양전지 기판으로 사용되는 금속기판의 우수성은 잘 알려져 있다. 그러나 상용 금속기판이 직면하고 있는 문제점을 보완하기 위해서 전주법으로 제조된 2원합금 금속포일을 개발하였으며, 박막형 및 플렉서블 태양전지의 기판재로 적용가능성을 확인하였다. 일반적으로 태양전지를 제조할 때 열 공정이 수행되며, 이때 기판재와 cell을 구성하는 반도체의 열팽창 계수 차이에 의한 열변형으로 결함이 발생될 수 있고, 태양전지 효율 및 수명을 저하시키는 원인이 될 수 있다. 이러한 원인이 될 수 있는 구성 재료간의 열팽창계수 차이에 의한 cell 의 변형량을 추정하기 위해 유한요소해석 방법을 사용하였다. 유한요소해석을 수행하기 위해 ALGOR 라는 해석 tool 을 사용하였다. 유한요소해석 수행에 사용된 상용 금속인 Mo, Ti, Al, SUS 포일과 전주법으로 제조된 2원합금 금속포일의 열팽창 계수는 실험을 통한 측정치이며, cell을 구성하는 반도체의 열팽창 계수와 열특성은 참고 문헌에 있는 자료들이다. 이 값들을 기반으로 cell 의 구성을 단순화시킨 가상의 태양전지가 제조 공정 온도에서 상온으로 냉각될 때의 열변형량을 계산하였다.
-
The modular line-connected photovoltaic PCS (power conditioning system) is proposed. The proposed system consists of a step-up DC-DC converter and a full-bridge inverter. A step-up DC-DC converter using a dual series-resonant rectifier circuit and a active-clamp circuit is proposed to achieve a high efficiency and a high input-output voltage ratio efficiently. An IncCond (incremental conductance) MPPT (maximum power point tracking) algorithm that improves MPPT characteristic is used. By control a inverter using a linearized output current controller, a unity power factor is achieved. All algorithms and controllers are implemented on a single-chip microcontroller and the superiority of the proposed algorithms and controllers is proved by experiments.
-
본 논문에서는 UPS 기능을 갖는 단상 태양광 발전 시스템을 제안하였다. 제안하는 시스템은 태양광 어레이 (photovoltaic array)에서 최대전력을 얻기 위해 MPPT (maximum power point tracking)를 수행하는 컨버터, 계통전원 상태나 태양광 발전량에 상관없이 부하에 정현파 전압을 공급하는 인버터, 태양광 어레이에서 발전된 잉여전력을 계통으로 전달하거나 부하에 필요한 전력을 dc bus로 공급하는 인버터, 정전시 dc bus에 전력을 공급하는 양방향 컨버터 (bidirectional converter)로 구성된다. 제안하는 시스템은 발전된 전력을 계통으로 전달할 뿐만 아니라, UPS (uninterruptible power supply)기능도 수행하는 시스템으로 계통전압이 불안정하거나 정전시에도 부하에 안정적이고 깨끗한 전압을 항상 공급할 수 있다. 각각의 인버터, 컨버터, 및 양방향 컨버터는 dc bus를 공유하며, dc bus의 전압에 따라 동작상태가 결정이 된다. dc bus중심의 제어는 dc bus전압을 안정적으로 유지시키며, 부하에 걸리는 전압의 변동을 최소로 하고 시스템의 디자인 및 제어를 단순화한다. 모든 알고리즘과 제어기를 하나의 마이크로 컨트롤러로 구현하였고 제안된 시스템의 우수성을 실험을 통해 검증하였다.
-
In this study, we have attempted a new method to enhance the coloring of dye on the
$TiO_2$ surface in the dye sensitized solar cell. In the conventional coloring process in a dye sensitized solar cells, dye is absorbed by the covalent bond between TiO2 and dye molecule while the photo-electrode coated with$TiO_2$ layer is soaked in dye solution for about 12-24 hours. But this process takes long time, so we have researched more effective and faster way than the conventional process by applying electric field. Three kinds of electric power such as direct voltage, alternating voltage and pulse voltage were applied to the transparent conducting oxide during the coloring process. As a result, we achieved improved power, fill factor and efficiency of dye-sensitized solar cell in case of applying direct voltage and pulse voltage. In contrast, alternating voltage tend to reduce the dye adsorption on the$TiO_2$ surface and hence the efficiency. We measured the absorption spectra of dye by UV-VIS spectrophotometer before and after soaking the$TiO_2$ in the dye and found no characteristic change in the dye was observed. In this study, we researched on shortening time of coloring process which spent much time in the whole process. -
다결정 태양전지의 원료인 폴리실리콘을 생산하는 방법 중 하나인 지멘스 방법에서 사용되는 실리콘 코어로드를 금속 계열의 코어로드로 대체하기 위한 연구를 진행하였다. 본 연구에서는 실리콘 코어로드의 대체물질 후보로서 고융점 금속인 텅스텐, 탄탈륨, 몰리브덴을 선택하였고, co-sputtering system을 이용하여 다성분계의 박막을 실리콘 기판에 증착시켜
$800^{cdot}C$ 에서$1000^{cdot}C$ 의 고온에서 열처리 후 박막의 형상변화 및 확산정도를 관찰하였다. 열처리 온도에 따른 박막의 형상 및 확산 정도를 관찰하기 위하여 Scanning electron microscopy (SEM), X-ray diffractometer(XRD), transmission electron microscopy(TEM), auger electron spectroscopy(AES)가 사용되었다. -
-
Poly(ethylene glycol) dimethyl ether (PEGDME)/fumed silica/ 1-methyl -3-propylimidazolium iodide (MPII)/
$I_2$ mixtures were used as polymer electrolytes in solid state dye-sensitized solar cells (DSSCs). The contents of MPII were changed and the concentration of$I_2$ was fixed at 0.1 mole% with respect to the MPII. The maximum ionic conductivity was obtained at [EG]:[MPII]:[$I_2$ ]=10:1.5:0.15. It was supposed that the maximum of ionic conductivities would match with that of cell efficiencies, if the ionic conductivity is a rate determining step in the sol id state DSSCs. However, the maximum composition did not show the maximum solar cell performance, indicating the mismatch between ionic conductivity and cell performance. This suggests that the ionic conductivity may not be the rate controlling step in determining the cell efficiency in these experimental conditions, whereas other parameters such as the electron recombination might play an important role. Thus, we tried to modify the surface of the$TiO_2$ particles by coating a thin metal oxide such as$Al_2O_3$ or$Nb_2O_5$ layer to prevent electron recombination. As a result, the maximum of the cell efficiency was shifted to that of the ionic conductivity. The peak shifts were also attempted to be explained by the diffusion coefficient and the lifetime of electrons in the$TiO_2$ layer. -
Supramolecules containing double hydrogen bonding sites at their both chain ends were self-polymerized to become solid state polymer and were utilized to improve the efficiency of solid state DSSCs. Hydrogen bonding sites were attached at the chain ends of PEG of Mw=2000, such as pyrimethamine and glutaric acid. The solar cell with the solid state supramolecular polymer electrolyte resulted in the overall energy conversion efficiency of 4.63 % with a short circuit current density
$(J_{sc})$ of 10.41$mAcm^{-2}$ , an open circuit voltage$V_{oc}$ , of 0.71 V and a fill factor (FF) of 0.62 at one sun condition ([oligomer]:[1-methyl-3-propyl imidazolium iodide (MPII)]:$[I_2]$ = 20 : 1 : 0.19, active area = 0.16$cm^2$ ,$TiO_2$ layer thickness = 10${\mu}m$ ). The ionic conductivity of the sol id state electrolyte was$5.11{\times}10^{-4}$ (S/cm). The cell performance was characterized by electrochemical impedance spectroscopy and ionic conductivity. -
최근 다수의 태양광 발전기가 배전계통에 연계되고 있으며 특히, 특정지역을 중심으로 대규모의 태양광발전 단지가 구성되어 배전계통에 연계되고 실정이다. 본 논문에서는 순천에 구축된 l000KW급 태양광발전소의 계통해석영향을 분석하기 위하여 PSCAD/EMTDC 툴을 이용하여 모델링 하고 태양광발전이 연계된 배전계통 조류해석과 태양광 발전의 출력에 의한 22.9KV 배전계통의 전압변동을 시뮬레이션 하였으며, 태양광발전에 따른 역조류에 의한 배전계통 전압변동을 분석하였다. 또한, 태양광발전기의 배전계통 연계 전,후의 배전선로의 임의의 지락고장 모의로 태양광발전기가 고장전류에 미치는 영향 분석과 태양광 발전이 양호, 불량한 경우에 대한 상전압, 고조파 전류, 역률 등의 측정결과에 의한 전력품질을 분석 하였다.
-
CdSe nanoparticles were prepared by chemical solution methods using
$CdCl_2{\cdot}4H_2O$ (or$Cd(NO_3)_ 2{\cdot}4H_2O$ ) and$Na_2SeSO_3$ . The characteristics of CdSe nanoparticles were controlled by the react ion time, reaction temperature and reaction method as well as the surfactants. Cetyltrimethyl ammonium bromide(CTAB) was used as a capping agent to control the chemical reactions in aqueous solution. Polyvinylalcohol(PVA) was used as a templet in sono-chemical method. CdSe nanoparticles synthesized in aqueous solution showed homogeneous size distribution with relatively stable surface. CdSe nanoparticles synthesized in non-aqueous solution containing diethanolamine(DEA) showed the structure transformation from cubic to hexagonal as the reduction temperature increased from 80 to$160^{\circ}C$ . Core shell CdSe was synthesized by sono-chemical method. Characteristics of CdSe nanoparticles were analyzed using transmission electron microscopy(TEM), x-ray photoelectron spectroscopy(XPS), x-ray diffraction(XRD), UV-Vis absorption spectra, fourier transform infrared spectroscopy(FT-IR) and photoluminescence spectra spectroscopy(PL). This paper presents simple routes to prepare CdSe nanoparticles for solar cell applications. -
-
-
-
-
Wind turbine is composed by 3 major parts, rotor ass'y, nacelle ass'y and tower. There are two major point in nacelle cover analysis one is nacelle cover itself the other is cover support structure. Both of them are required strength proof with light weight. For the design of structure, the loads are calculated according to GL wind guideline Ed. 2003 and by the commercial F.E. codes,
-
-
Lee, Hyun-Young;Kang, Sin-Il;Kwon, Oh-Jung;Choi, Hyo-Jin;Kwon, Sei-Jin;Son, Yoon-Gyu;Suh, Jae-Hak;Jang, Sung-Duk;Oh, Jong-Seok;Lee, Byung-Chul;Hwang, Jin-Su;Ryu, Ji-Yoon 336
본 논문에서는 750kW 풍력발전용 인버터를 개발한 결과와 2년 동안의 현장실증을 통하여 얻어진 경험을 바탕으로 2MW 영구자석형 동기발전기(RMSG, Permanent Magnet Synchronous Generator)의 전력변환을 위한 병렬형 인버터의 시뮬레이션과 이를 통한 설계와 제작 및 기본시험 과정을 소개하고자 한다. -
This paper addresses the measurement of structural loads on the Unison U50 wind turbine. The load measurement are carried out to determine the actual loads acting on a wind turbine. This is needed not only the certification process but also improving the technical development for prototype wind turbine. The measurement system is consists of measuring load, operating quantities and meteorological signal. All data that occur during the operating of a WT are stored the data acquisition system automatically. With using the measured data, load spectrum and equivalent load are evaluated according to IEC61400-13 "Measurement of mechanical loads".
-
국내 업체인 유니슨에서는 750kW Gearless형 풍력발전기, U50을 개발하였다. 개발된 풍력발전기는 대관령 풍력실증연구단지에 설치되었다. 풍력시스템의 전력품질 측정 및 평가는 계통에 대한 영향을 조사하는데 있어서 중요한 요소이다. 이 논문에서는 전력품질에 대한 국제기준인 IEC61400-21을 적용하여 U50풍력발전기의 전력품질에 대한 데이터 수집 및 수집된 데이터를 통해 U50풍력발전기가 계통에 미치는 전력품질의 영향을 검토하였다.
-
A GFRP based composite blade was developed for a 2MW wind energy conversion system of type class IIA. The blade sectional geometry was designed to have a general shell-spar and shear web structure. The load cases specified in the IEC61400-1 international specification were considered. For withstanding all relevant extreme loads, the structural analysis for the complete blade was performed using a commercial FEM code. The static load carrying capacity, blade tip deflection and natural frequencies were evaluated to satisfy the strength and stability requirements in accordance with the IEC61400-1 and GL Regulations. The prototype blade was passed the structural proof test for GL certification.
-
환경규제 강화와 화석연료에 대한 대안으로 신/재생에너지에 대한 관심이 고조 되고 있다. 그 중 하나인 풍력발전은 각국마다 풍황 조건과 정책에 의해 다양한 시장을 만들어 내고 있다. 본 연구는 해상풍력발전시스템의 투자 전망에 대하여 기존의 재무적 평가기법에 학습곡선효과를 가미하는 방법론을 제시하고자 하였다. NPV 등의 가치 평가기법이 할인된 현금흐름 분석을 하는 것이라면 이에 더하여 현금의 유출에 있어서 학습율을 반영한 원가를 반영하는 것이 제시하고자 하는 연구 방법론의 핵심이다. 해상풍력발전을 투자자 입장에서 모의 해본 결과 국내 풍력발전은 80% 학습율 수준 정도의 혁신적 개선 없이는 투자 타당성을 찾기 어려우며 이러한 현실적인 문제점을 정책적으로 보완해야 할 수 있는 것이 발전가격을 중심으로 하는 정부의 지원제도임을 제시 하였다.
-
Any investment analysis has to deal with the uncertainty that arises over the course of operating the invested project. When it comes to an wind power, such analysis gets even more complicated, as the wind resource or the current is inherently unstable and unpredictable. Different from predecessors in the field of analyzing wind power economics, this paper proposes a stochastic methodology of analyzing the economic efficiency of an investment in wind power to explicitly address those uncertainties or risks. A probability distribution is assigned to each variable to generate a probability distribution of the economic value of an investment through a Monte-Carlo simulation
-
풍력 발전기의 블레이드 설계를 위하여 각 설계 변수에 대한 영향을 파악하기 위하여 연구를 수행하였다. 블레이드의 공력 형상을 결정짓는 설계 변수를 분류하고 이에 대하여 parametric study를 통하여 각 설계 변수가 주어진 환경에서 블레이드의 성능 및 하중에 어떠한 영향을 주는 가에 대하여 살펴보았다. 이를 블레이드의 성능 및 기준 하중에 대한 해석은 BEMT를 이용하였다. 본 결과는 블레이드의 실제 공력 설계에서 설계 변수의 선정과 그 영향에 대하여 미리 파악하는데 도움을 줄 것으로 기대된다.
-
Mr. Hur has developed the 7500KW permanent magnet synchronous generator. The 7500KW generator has dual blade system with vertical axis type generation module. The 7500KW generator will generating that it is too expensive and construction payment. The advantages of dual blade system are cheap in generation with better efficiency, and safety compact structure. But also this system has the expensive slide ring for to distribute electrical power.
-
This study suggests a modeling of grid-connected wind turbine generation system that has induction generator, and aims to perform simulations for outputs by the variation of actual wind speed and for fault current of wind generation system by the transformer winding connection. This study is implemented by matlab&simulink. The simulation shall be performed by assuming single line to ground fault generated in the system. Generator power, generator rotor speed, generator terminal current and fault current shall be observed following the performance of simulation. The fault current change will be dealt through the simulation results for fault current of wind generation system following the grid-connected transformer winding connection and the simulation result by the transformer neutral ground method.
-
750kW gearless type wind turbine, named U50, is developed by UNISON in Korea. The newly developed wind turbine should be evaluated the power curve and the estimated annual energy production by following international standard to verify the power performance characteristics. This paper shows the test and evaluation procedure according to IEC 61400-12-1 which specifies a procedure of measuring the power performance characteristics of a single wind turbine and applies to the testing of wind turbines of all types and sized connected to the electrical power network. And this paper also shows the power performance characteristics for U50 wind turbine which is determined in accordance with IEC regulation.
-
In accordance with Madrid and Kyoto Protocols, a 10kW wind turbine installed about 625m away from the King Sejong Station in the Antarctica has been in operation successfully. The current location of the wind turbine has different geographic surroundings from the previous candidate site considered in 2005 and that makes re-evaluation of wind resource at the current site including geographic effects necessary. Especially, strong wind flow derived by steep and complex terrain is dominant in the Antarctica so that computational flow analysis is required. The wind rose measured at the previous and current installation location are identical with strong meteorological correlation but prevailing directions of wind power density are different because of local wind acceleration due to complex terrain. Numerical analysis explains which effects brings this discordance between the two sites, and a design guideline required for additional wind turbine installation has been secured.
-
탄소섬유가 중앙에 적층된 풍력발전용 블레이드 소재인 탄소 유리섬유 하이브리드 복합재료가 VARTM(Vacuum Assisted Resin Transfer Molding)공법을 이용하여 제작되었다. 아이조드 충격시험법을 이용하여 온도, 하이브리드화 비율 그리고 노치에 대한 충격강도의 영향을 연구하였다. 온도 감소 및 탄소섬유의 증가에 의해 충격강도는 감소하는 경향을 보였으며, 노치에 의해 하이브리드 복합재료는 약
$25{\sim}30$ %가량의 충격강도 감소를 보였다. 그러나 단일 탄소섬유 복합재료의 경우 노치민감도는 없었으며, 이에 소량의 유리섬유 첨가로 인해 하이브리드화 하였을 경우 충격강도 향상 및 저온 충격강도 안정성을 확보 할 수 있었다. -
The optimal design and characteristic analysis of Double Fed Induction Generator(DFIG) was performed. The purpose of the paper is to verify the accuracy of design and the reliability of DFIG by experiment. A grid connection experiment is performed to confirm generating performance in wide operating range. In this experiment, 2.7MW M/G set is used. The finite element method is applied to calculate parameters and characteristic analysis of DFIG. And in order to reduce design time and efforts, Design of Experiment(DOE) is used. The experimental results are compared with the optimum design results.
-
-
Recently the diameter of the 5MW wind turbine reaches 126m, and the tower height is nearly the same with the wind turbine diameter. The blade will experience periodic inflow oscillation due to blade rotation inside the ground shear flow region, that is, the inflow velocity is maximum at uppermost position and minimum at lowermost position. In this study we compare the aerodynamic data between two inflow conditions, i.e, uniform flow and normal wind profile. From the computed results all of the relative errors for oscillating amplitudes increased due to the ground shear flow effect. Especially My at hub and
$F_x$ ,$M_y$ ,$M_z$ at LSS increased enormously. It turns out that the aerodynamic analysis including the ground shear flow effect must be considered for fatigue load analysis. -
Wind turbine gearbox is a complex mechanical system that includes gear trains, shafts, bearings, and gearbox housings. All these components are interacting with each other therefore it is important to assess the whole performance by considering the individual component design. In this paper, the performance assessment of 2MW wind turbine gearbox was conducted under various operating conditions at test bench and test result was compared with the design calculation.
-
-
풍력 블레이드용으로 설계된 에어포일에 대하여 풍동 시험을 수행하였다. 설계된 에어포일의 레이놀즈수 범위에 맞추고자 코드 길이 40cm의 모델에 대하여 유속 17m/s, 35m/s, 50m/s에 대하여 에어포일 표면에서의 압력과 에어포일 뒤쪽 레이크에서의 압력을 측정하였다. 이를 통하여 설계에 사용된 기법의 타당성과 설계된 에어포일에 대하여 설계 변수에 대한 실질적 만족도에 대하여 평가하였다. 이와 더불어 표면 거칠기에 대한 모사를 위하여 트립도트를 부착하여 시험을 수행하였다. 이를 통하여 레이놀즈수와 표면 거칠기에 따른 에어포일의 성능 및 유동 변화 특성에 대하여 파악 할 수 있었다.
-
발전소 온배수의 원활한 배수를 위한 설계 낙차와 함께 남서해안의 조위변화에 따른 낙차의 이용가능성을 인지하고 소수력 발전 방식과 조력발전 방식의 특정을 동시에 활용하는 해양소수력 발전소를 삼천포 화력발전소 배수로에 최초로 건설하여 운전함으로써 청정 재생에너지 개발 및
$CO_2$ 저감효과 창출에 이바지하고 있다. 본 연구에서는 삼천포 해양소수력 발전소의 운전실적 자료를 토대로 조위 및 방류량의 변화에 따른 해양소수력의 효율 특성을 분석하고자 한다. 해양소수력 발전소의 효율은 방류량과 유효 낙차의 영향을 직접적으로 받기 때문에 관측한 수위 및 방류량, 해양소수력발전소 운전실적 자료를 토대로 효율분석을 실시하였다. 우선, 소수력 가동 이후 배수로에서의 수위 상승이 명확히 나타났으며, 배수로내 위어에서의 흐름구조가 완전월류 상태에서 불완전월류로 바뀌면서 배수로 전체의 수면 불안정성이 크게 증가하였으나, 배수로의 범람이나 순환수 계통에의 큰 영향을 초래할 만한 수준은 아니었다. 성능시험 결과, 최대출력, 평균출력, 최소출력 모든 부분에서 설계 보증치 이내의 값을 보였으며, 효율 또한 설계 보중치를 상회하는 결과를 보였다. CWP 유량 분석결과, 소수력 발전소에서의 유량이 과소 측정되고 있음을 확인하였으며, 최대낙차에서 최대효율을 보이고, 저낙차일 때는 보증치보다 효율이 낮게 나타나는 결과를 보였다. 또한 조위조건을 고려한 유량을 이용하여 산정한 효율 곡선이 보증치와 가장 일치하였으며, 전체 시스템 효율은 비교적 양호한 상태임을 알 수 있었다. -
-
The small hydropower uses hydraulic power to generate electricity, which one of the future energy resources of the power industry. The tubular turbine which uses in the city water pipe lines's differential pressure electricity is produced, this structure is simple, and therefore advantageous. The effects of cavitation that occurs in the turbine is researched, By using CFD we analysed the flow pattern inside the turbine. As a result, we found out to become the performance fall of turbine.
-
1982년 동력자원부의
${\lceil}$ 소수력개발방안${\rfloor}$ 에 의해 민간인이 소수력발전사업에 참여할수 있는 제도가 만들어진 이후 초기단계에는 (1985년${\sim}$ 1995년) 많은 사업자가 소수력발전사업에 참여하여 성공도 하고 실패도 하였지만 1995년 이후에는 수자원공사, 농촌공사, 그리고 지방자치단체 만이 소수력발전소 건설에 참여하였다. 수중보를 이용한 민간인의 소수력 개발도 활성화 되기 바란다. -
Oxy-gasification or oxygen-blown gasification, enables a clean and efficient use of coal and opens a promising way to CO2 capture. The coal gasification process of a slurry feed type, entrained-flow coal gasifier was numerically predicted in this paper. The purposes of this study are to develop an evaluation technique for design and performance optimization of coal gasifiers using a numerical simulation technique, and to confirm the validity of the model. By dividing the complicated coal gasification process into several simplified stages such as slurry evaporation, coal devolatilization, mixture fraction model and two-phase reactions coupled with turbulent flow and two-phase heat transfer, a comprehensive numerical model was constructed to simulate the coal gasification process. The influence of turbulence on the gas properties was taken into account by the PDF (Probability Density Function) model. A numerical simulation with the coal gasification model is performed on the Conoco-Philips type gasifier for IGCC plant. Gas temperature distribution and product gas composition are also presented. Numerical computations were performed to assess the effect of variation in oxygen to coal ratio and steam to coal ratio on reactive flow field. The concentration of major products, CO and H2 were calculated with varying oxygen to coal ratio (0.2-1.5) and steam to coal ratio(0.3-0.7). To verify the validity of predictions, predicted values of CO and H2 concentrations at the exit of the gasifier were compared with previous work of the same geometry and operating points. Predictions showed that the CO and H2 concentration increased gradually to its maximum value with increasing oxygen-coal and hydrogen-coal ratio and decreased. When the oxygen-coal ratio was between 0.8 and 1.2, and the steam-coal ratio was between 0.4 and 0.5, high values of CO and H2 were obtained. This study also deals with the comparison of CFD (Computational Flow Dynamics) and STATNJAN results which consider the objective gasifier as chemical equilibrium to know the effect of flow on objective gasifier compared to equilibrium. This study makes objective gasifier divided into a few ranges to study the evolution of the gasification locally. By this method, we can find that there are characteristics in the each scope divided.
-
In the current most tool using heat and mass balance in a coal gasifier is dependent on commercial code such as STANJAN, CHEMKIN. However, in order to keep the self-reliance technology, it is necessary to develop the original design tool available for comprehension and analysis on the spot. So in this study, its own heat and mass balance program is developed on the assumption that the process in a coal gasifier is adiabatic and quasi-equilibrium. The mass balance is calculated by using the chemical equilibrium principle. Also the heat and mass balance according to main operating factors such as temperature, pressure and O2/Coal ratio, was carried in this tool. This heat and mass balance was verified on the basis of the results simulated in STANJAN, commercial codes using similar logic.
-
Gasification has been regarded as a very important technology to decrease environmental pollution and to obtain higher efficiency, The coal gasification process converts carbon containing coal into a syngas, composed primarily of CO and
$H_2$ . And the coal syngas can be used as a source for power generation or chemical material production. This paper illustrates the operation characteristics and results of pilot-scale coal syngas production facilities. The entrained-bed pilot scale coal gasifier was operated normally in the temperature range of$1,300{\sim}1,400^{\cdot}C$ ,$2{\sim}3kg/cm^2$ pressure. And Indonesian KPC coal produced syngas that has a composition of$46{\sim}54$ % CO,$20{\sim}26$ %$H_2$ , and$5{\sim}8$ %$CO_2$ . -
가스화기술은 화석연료에 의한 기존의 화력발전기술을 대체할 수 있는 차세대 발전기술로 여겨지고 있어 전 세계적으로 기술개발은 물론 상용 플랜트를 앞 다투어 도입 건설 중에 있다. 현재 국내에서도 2014년까지 실증플랜트 완공에 매진을 가하고 있는 실정이다. 가스화기술은 온실가스인 이산화탄소를 동시에 감축하면서 전력뿐만 아니라 수소, DME, 화학원료와 같은 2차 고급 에너지원을 생산할 수 있다는 장점을 가지고 있다. 이 연구에서는 ASPEN plus를 이용하여 다양한 원료 공급에 따른 300 MW급 IGCC 플랜트에 대한 운전 특성을 알아보고자 하였다. 가스화기에 공급되는 원료는 석탄(역청탄), 중질유(납사, 벙커C유) 등으로 구분해 고려하였으며, 가스화 플랜트 해석모델에 대한 성능을 평가하기 위하여 해외에서 운전 중인 상용 IGCC 플랜트에 대한 운전자료와 상대오차로 비교 산출해 검증하였다. 그 다음으로 가스화(gasification)공정, 산가스 제거(acid gas removal)공정, 복합발전 공정(combined cycle)등과 같은 IGCC 플랜트를 구성하고 있는 각각의 단위공정에 대한 운전 특성에 대한 해석결과를 확인하였다. 해석 결과를 바탕으로 가스화기의 냉가스 효율(cold gas efficiency)과 탄소 전환율(carbon conversion), 산가스 제거공정에 대한 이산화탄소 포획 성능과 복합발전에 따른 플랜트 발전량 및 발전 효율(plant net efficiency)을 예측하였다.
-
Gasification converts coal and other feedstocks into a very clean and usable gas, called syngas, that can be used to produce a wide variety products such as electricity, chemicals, transports fuels, hydrogen production, etc. This paper was studied the gasification performance effects with the variation of the gasification operating parameters such as the feeding amounts of oxygen, steam and coal. When
$O_2/coal$ ratio was below 0.8,$H_2$ mole % was increased as increasing$O_2/coal$ ratio. CO mole % was increased when$O_2/coal$ ratio was below 1.2 as increasing the$O_2/coal$ ratio. As increasing steam/coal ratio,$H_2$ mole %was increased and CO mole % was decreased. The$O_2/coal$ and steam/coal ratio was$0.8{\sim}0.9$ and$0.0{\sim}0.4$ , respectively, to keep the proper gasification condition that the gasifier temperature was$1300^{\circ}C{\sim}1450^{\circ}C$ and the cold gas efficiency was over 76%. -
The inside wall of a coal gasifier is lined with refractory, and the corrosion of the refractory by coal sag is an important parameter affecting the refractory lifetime and the replacement period. This paper examines the changes in microstructure of a chromia refractory due to chemical reactions with penetrating slag as a function of slag composition. The effects of CaO and
$Fe_2O_3$ concentrations were studied using Datong and KIDECO slag. Static corrosion experiments were carried out, the percent slag penetration and changes in the microstructure were determined by SEM/EDX analyses. FactSage equilibrium calculations were carried out to determine the equilibrium products and the predictions were compared with experimental observations. -
석탄가스화 복합발전(IGCC)에서 석탄 가스화 기술이 전 공정의 성능에 큰 영향을 미치는 중요한 요소이다. 연료 및 산화제의 공급방식, 가스화기의 기본 구조, 벽면의 구성 방식, 용융 슬랙 및 생산되는 합성가스 배출 방식 등에 따라 가스화의 성능이 영향을 받는다. IGCC plant의 정확한 성능 해석을 위해서는 석탄가스화기 공정 모델의 정밀도를 높일 필요성이 있다. 기존의 열병합 발전 사이클 해석에서 적용되었던 열 및 물질정산과 평형계산 방식을 통하여 석탄가스화기 공정을 해석하는 방법을 확인, 정리하고 이를 개선하기 위한 절차 및 방안을 제시하고자 한다. 가스화기 내부 공정을 크게 탈휘발과 가스화의 단계로 구분하여 가스화기 출구조건을 예측하였으며, ASPEN PLUS를 이용한 공정해석을 실시하였다. 가스화기 출구에서의 합성가스는 주생성가스인 CO,
$H_2$ 를 위주로 하여 조성을 얻을 수 있고, 그 결과들을 선행연구들과의 비교를 통하여 가스화기 모델의 분석을 실시한다. 그리고 가스화기 해석의 정밀도를 높이기 위한 향후 고려될 가스화기 모델에 관하여 논의한다. -
The present study numerically investigate the effects of the Syngas chemical kinetics on the basic flame properties and the structure of the Syngas diffusion flames. In order to realistically represent the turbulence-chemistry interact ion and the spatial inhomogeneity of scalar dissipation rate. the Eulerian Particle Flamelet Model(EPFM) with multiple flamelets has been applied to simulate the combustion processes and NOx formation in the syngas turbulent nonpremixed flames. Due to the ability for interactively describing the transient behaviors of local flame structures with CFD solver, the EPFM model can effectively account for the detailed mechanisms of NOx format ion including thermal NO path, prompt and nitrous NOx format ion, and reburning process by hydrocarbon radical without any ad-hoc procedure. validation cases include the Syngas turbulent nonpremixed jet and swirling flames. Based on numerical results, the detailed discussion has been made for the sensitivity of the Syngas chemical kinetics as well as the precise structure and NOx formation characteristics of the turbulent Syngas nonpremixed flames.
-
감압 증류 후 생성되는 중질유의 고도화를 위하여 코킹 공정을 거친 후 정유 부산물로 생성되는 열적으로 매우 안정하고, 높은 발열량을 갖는 반면 황, 바나듐 함량이 높은 석유코크스의 효과적인 이용을 위하여 본 연구에서는 가스화 공정을 적용하였다. 1T/D 용량의 분류층 가스화기를 이용하여 유연탄(drayton coal), 석유코크스, 또는 혼합한 경우의 가스화 성능을 알아보았으며, 각각의 경우에 대하여 비교하여 보았다. 높은 열 안정성을 갖는 석유코크스의 효과적인 가스화를 위하여 반응기 내 체류시간 및 버너 노즐 변경에 따른 가스화 성능 개선을 시도하였으며, 이때의 온도, 산소/원료 공급량 조건에 따른 생성가스 성분 및 탄소전환율, 냉가스효율 변화 특성을 알아보았다. 버너 노즐 구경 변경으로 인한 슬러리의 미립화를 통하여 향상된 탄소전환율 및 냉가스효율을 얻을 수 있었다.
-
석탄가스화 기술은 석탄을 고온/고압 조건에서 가스화 반응시켜 CO와
$H_2$ 가 주성분인 합성가스(syngas)로 전환시키는 기술이다. 그러나 가스화 반응으로 인해 합성가스 내에는 불순물인$H_2S$ , COS,$NH_3$ 등의 오염 물질이 발생하게 되며, 가스터빈의 부식, 촉매의 피독, 전극의 성능 저하 현상 등을 일으켜 효율을 저하시키게 된다. 이에 본 연구에서는 FeMgO 촉매를 제거용매로 사용하여$H_2S$ 를 효과적으로 제거하기 위하여 Lab-scale 탈황 설비를 제작하였으며, 석탄 가스화 운전에 연계하여 합성가스 내 포함된 산성가스 정제 특성에 관한 연구를 진행하였다. -
석탄을 합성석유로 전환시키는 석탄액화(CTL) 공장은 2차 세계대전시 독일 및 영국에서 가동되어 대량의 연료를 공급한 바 있다. 전후 대형 유전이 발견되어 값싼 석유가 공급되면서 CTL 공장의 운전은 중단되었다. 남아프리카공화국의 Sasol사만이 유일하게 1955년에 CTL공장의 조업을 시작하여 현재 하루 15만배럴의 석탄합성석유를 생산하고 있다. 최근 고유가가 지속되고 석유공급에 대한 불안감 때문에 여러 개의 석탄액화 프로젝트가 진행되고 있다. 중국은 2030년까지 석탄합성석유를 연간 3천만톤(60만배렬/일) 생산할 계획을 수립하였고, 2만배럴/일 규모의 석탄직접액화공장이 2008년 완공될 예정이다. 미국에서도 8개의 CTL 프로젝트가 진행되고 있다. 호주, 필리핀, 인도네시아, 인도 등에서도 석탄액화 프로젝트를 추진하고 있다. 석유를 전량 수입하는 우리나라도 에너지안보 차원에서 CTL에 대한 접근이 필요하다. 본고에서는 한국에너지기술연구원에서 추진되고 있는 석탄 기준 10톤/일급 석탄 합성석유 생산 공정 설계, 설비 시공 현황 및 향후 계획에 대하여 기술하였다.
-
석탄가스화 수소생산 기술 분야는 석탄 등의 화석연료를 이용하여 고온, 고압하에서 반응가스(산소, 수증기, 수소)와의 화학적 반응을 통해 생산된 연소성 가스 (
$H_2$ , CO,$CO_2$ 등)를 전환반응(WGS) 및 분리반응을 거쳐 효율적으로 청정하게 수소를 생산해 내는 기술이다. 전력산업에서 석탄가스화 수소생산은 그 사용 방법(연료전지, 수소 터빈, 분산 이용 등)에 따라 발전시스템의 고효율화를 지향하고, zero-emission을 실현하는 첨단 발전 시스템의 종합 구현을 목표로 하고 있으며, 더불어, 도래하는 수소 경제로의 전이에 대비에 석탄을 이용한 중앙(Central) 수소생산 시스템을 구현하여 이송 및 전환을 통한 지역적 분산 이용을 가능케 하는 종합적인 인프라를 구축하는 기술이다. 본 기술에는 석탄가스화 기술, 수성가스 전환기술, 수소/$CO_2$ 분리기술, 이송용 연료 전환기술 등이 포함된다. 석탄가스화 수소생산 기술은 급등하는 오일 가격과 이의 수입사용 증가에 대응하기 위한 에너지 안보 대책 마련 및 효율 극대화의 필요성과 더불어, 전력산업에서 화력 발전시스템의 궁극적 실현 목표인 고효율, 초청정의 전력생산 시스템의 구현을 가능케 하여, 향후 화석 연료를 이용한 미래 발전 기술을 선도 할 것으로 기대된다. 더불어, 수소 경제로의 전환 시 수소 수요의 급팽창에 대비한 경제적인 대규모 수소생산 기술의 개발이 필요하며, 이에 기술 실현성이 가장 높은 석탄가스화 수소생산 기술의 개발 구현이 요구된다. -
-
Effluent ground water overflow in deep and broad ground space building. Temperature of effluent ground water is in
$12{\sim}20^{\circ}C$ annually and the quality of that water is as good as living water. Therefore if the flow rate of effluent ground water is sufficient as source of heat pump, that is good heat source and heat sink of heat pump. Effuent ground water contain the thermal energy of surrounding ground. So this is a new application of ground source heat pump. In this study open type and c lose type heat pump system using effluent ground water was installed and tested for it church building with large and deep ground space. The effluent flow rate of this building is$800{\sim}1000$ ton/day. The heat pump capacity is 5RT each. The heat pump cooling COP is$4.9{\sim}5.2$ for the open type and$4.9{\sim}5.7$ for close type system. The system cooling COP is$3.2{\sim}4.5$ for open type and$3.8{\sim}4.2$ for close type system. This performance is up to that of BHE type ground source heat pump. -
Inlet fluid temperature of the BRE in the geothermal heat pump system depends on heat exchange rate between the refrigerant of the heat pump and the leaving fluid from the BRE. Because the outlet fluid temperature of the BHE varies with time, inlet fluid temperature has to vary with time. In this study, the module to calculate inlet fluid temperature is developed, which can consider the time-varying outlet fluid temperature and the heat exchange capacity of the heat pump. It is assumed that heat loss or gain of the leaving fluid from outlet to inlet of the BHE is negligible, except when the fluid contacts with the refrigerant of the heat pump. This module is combined with TOUGHREACT, a widely accepted three-dimensional numerical simulator for heat and water flow and geochemical reactions in geothermal systems and is applied to data analyses of the thermal response test.
-
Efficiency of geothermal heat exchanger operation has close relation with temperature variation of the aquifer where the exchanger is installed. In the case of long-term operation, temperature distribution of the aquifer would be similar to that of water circulating in the exchanger, which causes the decrease of heat exchange rate. Therefore, the operation period of the heat exchanger should be controlled so that the temperature distribution of the aquifer is recovered. We developed a model to determine the operation period to acquire the optimal efficiency under the given aquifer condition. With this suggested method, when we use closed-loop heat exchanger, the operation efficiency of the geothermal heat exchanger is expected to be maximized by determining the optimal operation period.
-
Shin, Ji-Youn;Kim, Kyung-Ho;Bae, Gwang-Ok;Lee, Kang-Kun;Jung, Woo-Sung;Suk, Hee-Jun;Kim, Hyeong-Su 485
Riverbank filtration is a kind of artificial aquifer recharge for the fresh water supply. By construction of several production wells penetrating the riverbank, surface water withdrawn from the river would pass riverbed. This extracted water is well known to be cooler than surface water in summer and warmer than surface water in winter, showing more constant water temperature. This characteristic of extracted water is applied to geothermal energy utilization. Prediction of the annual temperature variation of filtrated water is the major concern in this study. In Daesan-myeon, Changwon-si, Gyeongsangnam-do, South Korea, riverbank filtration facility has been on its operation for municipal water supply and thermal energy utilization since 2006. Appropriate hydraulic and thermal properties were estimated for flow and heat transfer modeling with given pumping rate and location. With the calibrated material properties and boundary conditions, we numerically reproduced measured head and temperature variation with acceptable error range. In the numerical simulation, the change of saturation ratio and river stage caused by rainfall was calculated and the resulting variation of thermal capacity and thermal conductivity was considered. Simulated temperature profiles can be used to assess the possible efficiency of geothermal energy utilization using riverbank filtration facility. Influence of pumping rate, pumping location on the extracted water temperature will be studied. -
Understanding the thermohydraulic processes in the aquifer is necessary for a proper design of the aquifer thermal energy utilization system under given conditions. Experimental and numerical test were accomplished to evaluate the relationship between the geothermal heat exchanger operation and hydrogeological conditions in the open-loop geothermal system. Sand tank experiments were designed to investigate the open-loop geothermal system. Water injection and extract ion system as open-loop borehole heat exchanger was applied to observe the temperature changes in time at injection well, extraction well and ambient groundwater. The thermohydraulic transfer for heat storage was simulated using FEFLOW for two cases of extraction and injection phase operation in sand tank model. As one case, the movement of the thermal plume was simulated with variable locations of injection and extraction well. As another case, the simulation was performed with fixed location of injection and extraction well. The simulation and experimental results showed that the temperature distribution depends highly on the injected water temperature and the length of injection time and the groundwater flow and pumping rate sensitively affect the heat transfer.
-
본 연구에서는 국내 암석을 암종별로 총 292개 채취하였으며 열물성 측정 장비를 이용하여 이들 암석의 열물성을 측정하였다. 이와 더불어 암석의 물리적 특성을 측정하였으며 일부 시료의 경우 XRD 정량분석을 실시하였다. 이들 결과를 이용하여 암석의 열물성 특성과 열물성에 영향을 주는 인자를 파악하였다. 암석의 열물성 측정 결과 열전도도와 열확산계수는 화강암에서 가장 낮은 값을 보였으며 퇴적암, 변성암 순으로 나타났다. 또한 암종별 열물성 값의 범위를 살펴보면 변성암과 퇴적암에서 넓게 분포한다. 암석의 물성과 열물성과의 상관성 분석 결과 공극률이 증가함에 따라 열전도도와 열확산계수가 감소하나 상관성은 미약한 것으로 나타났다. XRD 분석 결과 암석의 열전도도는 석영(
$SiO_2$ )의 함량에 따른 선형의 비례관계를 보였다. 이로써 암석의 열전도도는 암석을 이루는 광물의 종류에 의하여 영향을 받음을 알 수 있다. 차후 암석의 구성 광물입자의 배열 상태에 따른 열물성 특성과 퇴적암 및 변성암 시료에 대한 이방성 실험을 통해 편리, 층리 및 엽리 등에 따른 열물생의 이방성 정도를 분석할 예정이다. -
지열류량은 지열자원 개발 시 지열 이상대를 찾는데 있어서 중요한 자료로 사용된다. 우리나라의 지체구조별 지열류량 평균은 경기육괴 66
$mW/m^2$ , 옥천습곡대 65$mW/m^2$ , 영남육괴 60$mW/m^2$ , 경상분지 72$mW/m^2$ , 연일분지 75$mW/m^2$ 이다. 이러한 대륙 내의 지표 지열류량은 상부 지각내의 방사성 동위원소 붕괴에 의한 열생산율(${\sim}40%$ )과 하부지각 및 상부맨틀에서부터 전도되어 올라온 지열류량(${\sim}60%$ )으로 설명할 수 있다. 따라서 지열류량의 결정에 있어서 열생산율의 정보는 중요한 부분을 차지한다. 열생산율은 지각 내에 존재하는 주요 방사성 동위 원소인 U, Th, K의 붕괴열에 의한 것이며, 열생산율의 측정은 gamma-ray log 자료를 이용하는 방법과 화학분석을 통한 방법이 있다. 이 연구에서는 두 가지 방법을 이용하여 총 123개(화강암 86개, 편마암 37개) 지점에서의 열생산율을 산출하였다. 화강암의 열생산율 평균은 2.15${\mu}W/m^3$ 이며, 편마암의 열생산율 평균은 2.22${\mu}W/m^3$ 로 나타났다. 지체구조별 열생산율의 평균은 경기육괴 2.52${\mu}W/m^3$ , 옥천습곡대 2.16${\mu}W/m^3$ , 영남육괴 2.35${\mu}W/m^3$ , 경상분지 2.01${\mu}W/m^3$ 로 나타났다. 지체 구조별 열생산율과 지열류량의 상관성 분석에서 우리나라의 경우 지열류량이 높은 지역에서 열생산율이 낮은 경향을 보인다. 따라서 열생산율이 지표 지열류량을 결정하는데 있어서 가장 중요한 요소가 아님을 확인할 수 있다. -
선구조 밀도에 따른 지열류량 분포 특성을 파악하기 위하여 선구조의 빈도 및 연장에 의한 선구조 밀도 분포도를 각각 작성하고, 측정 위치별 지열류량 값과 비교 분석하였다. 두드러진 단층의 발달과 많은 온천이 분포하는 경상분지 남부를 연구 대상지역으로 하였으며, 음영기복도 및 위성영상으로 부터 1km 이상되는 1337개의 선구조를 추출하였고, 빈도및 길이에 따른 선구조 분포 밀도도를 작성하였다. 연구 지역 내 51개의 지열류량 자료를 이용하여 측정위치별 선구조 밀도 값을 획득하고 지열류량 값과의 상관성을 파악하기 위하여 선형회귀 분석을 실시하였다.
-
Greenhouses should be heated during nights and co Id days in order to fit growth conditions in greenhouses. Ground source heat pump(GSHP) or geothermal heat pump system(GHPs) is recognized to be outstanding heating and cooling system. Horizontal GSHP system is typically less expensive than vertical GSHP system but requires wide ground area to bury ground heat exchanger (GHE). In this study, a horizontal GSHP system with thermal storage tank was installed in greenhouse and investigated as performance characteristics. In the daytime, heating load of greenhouse is very small or needless because solar radiation increases inner air temperature. The results of study showed that the heating coefficient of performance of the heat pump(
$COP_h$ ) was 2.9 and the overall heating coefficient of performance of the system($COP_{sys}$ ) was 2.4. Heating energy cost was saved 76% using the horizontal GSHP system with thermal storage tank. -
This study was performed to construct a geothermal data base about thermal conductivity of ground heat exchanger and thermal properties of grouting material which used to refill the borehole. We have acquired geothermal data sets from 39 sites over wide area of South Korea except to Jeju island. From data analysis, the range of thermal conductivity is
$1.5{\sim}4.0$ W/mK. It means that thermal conductivity varies with grouting material as well as regional geology and ground water system. -
Because of their low operating and maintaining costs, ground-source heat pump(GSHP) systems are an increasingly popular choice for providing heating, cooling and water heating to public and commercial buildings. Despite these ad- vantages and the growing awareness, GSHP systems to residential sectors have not been adopted in Korea until recently. A feasibility study of a residential GSHP system was therefore conducted using the traditional life cycle cost(LCC) analysis within the current electricity price framework and potential scenarios of that framework. As a result, when the current residential electricity costs for running the GSHP system are applied, the GSHP system has weak competitiveness to conven- tional HVAC systems considered. However, when the operating costs are calculated in the modified price frameworks of electricity, the residential GSHP system has the lower LCC than the existing cooling and heating equipments. The calculation results also show that the residential GSHP system has lower annual prime energy consumption and total pollutant emissions than the alternative HVAC systems considered in this work.
-
In this study, NR GT 101 (water-to-water Ground source heat pump unit) and NR GT 102 (water-to-air Ground source heat pump unit) related with ISO and ARI guideline were introduced and researched. GSHPs testing was performed by NR GT 101, 102 and analyzed performance factors. Test result, Energy Efficiency Ratio and Coefficient of performance factor of GSHPs were relatively low at an average value rather than Certification.
-
Geothermal Energy is related part of important the technology, and getting Patent statistics and analysis are targeted to Koran, Japan and America. Accoding to patent statistics, checking the analysis, developing speed of technology in korean and technology level and compared with America between Japan of technology. In this paper, Give help to national level can be achieved by reinforcing companies R&D, putting more concern and effort on getting straegical patents, activation of jog invention, expanding the quality Intellectual property(IP) & licensing Personnel, building a system responsive to international patent dispute. and national level can be archived by encouraging &supporting R&D of core technology, overseas applications of IP rights
-
In order to characterize the thermal conductivity and viscosity of grout materials used for backfilling ground heat exchangers, nine bentonite grouts and cement grouts being adapted in the United State have been considered in this study. The bentonite grouts indicate that the thermal conductivity and viscosity increase with the content of bentonite or filler (silica sand). In addition, material segregation can be observed when the viscosity of grout is relatively low. The saturated cement grouts appear to possess much higher thermal conductivity than the saturated bentonite grouts, and the reduction of thermal conductivity in the cement grouts after drying specimens is less than in case of the bentonite grouts. Maintaining the moisture content of grouts is a crucial factor in enhancing the efficiency of ground heat exchangers.
-
국토가 좁고 천연자원이 부족한 우라나라에서 전기생산의 대부분을 원자력 발전에 의존하고, 화력발전을 많이 활용하는 것은 당연한 일이다. 그러나, 각종 신기술의 개발과 함께 신에너지원에 대한 가능성이 증대되고 있어 이에 대한 연구와 투자도 소홀히 할 수 없는 상황에 있다. 신에너지원으로 거론되는 여러 가지 대안 가운데 비교적 국내기술로 접근하기 쉬운 부분이 지열을 활용한 분야이다. 일본, 필리핀, 인도네시아와 같은 화산국은 물론이고 우리나라와 같이 활화산이 없는 나라에서도 대심도에서는 지열자원이 고르게 분포해 있을 것으로 추정되어 개발된 지열활용기술은 그 수요처가 상당히 넓다고 할 수 있다. 본 연구에서는 지열활용을 위하여 필수적으로 사용되는 지열정 굴착기법과 건설에 따라 우려되는 환경영향을 정리하였다. 지열활용에 사용되는 지열정의 종류를 파악하고, 그에 따른 굴착기술을 소개하였으며, 저비용 고효율 굴착을 위한 요소기술들을 정리하였다. 그리고, 국외의 자료를 통하여 지열발전 프로젝트에서 우려되는 환경영향을 조사하여 국내의 상황과 비교하여 고찰하였다.
-
An expansion device plays an important role in optimizing the heat pumps by controlling refrigerant flow and balancing the system pressures. Conventional expansion devices are being gradually replaced with electronic expansion valves due to increasing focus on comfort, energy conservation, and application of a variable speed compressor. In addition, the amount of refrigerant charge in a heat pump is another primary parameter influencing system performance. In this study, the flow characteristics of the expansion devices are analyzed, and the effects of refrigerant charge amount on the performance of the heat pump are investigated at various operating conditions. Cooling capacity of the heat pump system is strongly dependent on load conditions. The heat pump system is very sensitive with a variation of refrigerant charge amount. But, the performance of it can be optimized by adjusting the flow rate through expansion device to maintain a constant superheat at all test conditions.
-
A semi-closed loop ground heat exchanger is proposed and its performance is compared through the measuring the effective thermal conductivity of the ground. In-situ tests based on the line source model are carried out to evaluate the thermal characteristics of each ground heat exchanger which has different penetration water flow rate. The test results show the increasing effective thermal conductivity of ground as the penetration water flow rate(PWFR) is increased. Therefore, the higher thermal performance of the proposed semi-closed ground heat exchanger can be expected.
-
지열 냉난방 시스템의 설계는 냉난방 공간의 크기에 따라 필요한 부하를 계산하여 설계하게된 다. 설계 부하를 충분히 소화할 수 있는 지열교환기의 길이와 보어홀의 깊이 및 개수는 지반의 열적 특성에 크게 좌우된다. 열전도율이 큰 지반일수록 지열교환기 내의 열 흡수 및 소산이 효과적으로 이루어져 지열교환기의 길이도 상대적으로 짧아질 수 있다. 즉, 효율적이고 정확한 설계를 하기 위해서는 지반, 암반 및 지중열교환기의 물리적 특성에 따른 열적 특성을 설계자는 미리 숙지하여야 한다. 현재 국내에서 수직 밀폐형 지중열교환기의 그라우트로 벤토나이트를 가장 많이 사용하고 있으나, 해외의 경우 지중 조건에 따라 시멘트 또는 벤토나이트를 적절히 선택하여 시공하고 있다. 이는 벤토나이트의 특성상 적용 조건이 제약을 받기 때문이며, 특히 지하수가 존재하지 않을 경우 사용이 사실상 불가능하다. 국내에서 이에 대한 충분한 연구는 아직 이루어지지 않았으며, 시멘트 그라우트를 사용하기 위한 물리적, 열적 특성에 대한 연구가 필요한 시점이라 판단하여 본 연구를 수행하였다. 시멘트 그라우트의 경우 수화반응이 일어나는 초기의 건조수축을 최소화하는 배합비로 물성을 구성하였으며, 벤토나이트는 일반 현장 시공 비율을 사용하였다. 열전도율은 첫째 실내 시험으로 시멘트 그라우트에 대한 열판시험법과 벤토나이트 그라우트에 대한 탐침시험법으로 수행하여 구하였으며, 두 번째 방법인 현장 시공으로 직접 현장열응답시험을 수행하여 그라우트 간의 열적 특성을 비교하였다. 또한 기존 시멘트그라우트의 열적 특성을 개량한 코오롱건설에서 개발한 시멘트 그라우트에 대한 열적 거동도 기존 타 그라우트의 열적 거동과 비교하였으며, 개발 제품의 성능이 상당히 우수함을 알 수 있었다.
-
A one-dimensional heat transfer model coupled with parameter estimation is developed in this study to predict the effective thermal conductivities of soil formation and borehole resistances from in situ field test data. In this application a new method of using initial ignoring time(IIT) obtained from error estimation is tried and turned out to be successful in determining soil thermal conductivities. The validity of this model is accomplished through comparison of the predicted temperature profiles of the model with the data from laboratory scale experimental setting. Eleven test boreholes were constructed in Ochang, Chungcheong Buk Do, and thermal response test was carried out with each borehole. The results of the in situ tests were analyzed with our 1-D numerical model and compared with the results of line source method. The comparison shows that the thermal properties from line source method is a little lower (
${\sim}95%$ )than those from numerical method. The reason of such result seems to be the lower thermal conductivity of grout material, which is not counted in line source method. -
정부는 2005년부터 가스하이드레이트 개발사업단을 발족시켜 국내의 가스하이드레이트 부존 형태와 매장량 평가를 위해 노력하고 있다. 2005년 2차원 정밀 물리탐사, 심해 퇴적물 채취 및 다각적 분석연구사업이 수행되었고, 2006년도에는 3차원 물리탐사, 개발기술을 위한 연구 및 지질재해
${\cdot}$ 안정성 연구 등이 수행되었다. 또한 2007년 상반기에 동해 지역에서 해저면 표면에서 피스톤 코어를 이용하여 실물 샘플을 채취하는 데 성공하였다. 기존에 취득된 다양한 자료를 면밀히 분석하고 해석한 결과를 바탕으로 2007년도 하반기에 시추를 진행 중에 있다. 시추를 통하여 동해지역의 가스하이드레이트의 부존 형태 파악 및 추정 매장량을 산출할 수 있는 좋은 결과가 취득될 것으로 기대하고 있다. 시추는 다양한 검층 및 압력코어 시스템을 포함한 코어채취가 수행되고 있다. 취득된 시추 결과를 이용하여 사업단은 가스하이드레이트 개발을 위한 보다 나은 결과를 도출한 것이며 이를 통해 미래 에너지원의 확보 및 자원 강국으로 가는 초석을 마련하게 될 것으로 기대한다. -
속도와 밀도의 함수로 이루어진 음향 임피던스는 탄성파자로부터 물성변화를 확인하는 방법 중의 하나로 이용된다. 본 연구에서는 한국지질자원연구원에서 개발된 탄성파 탐사자료처리 무른모 지오빗올 이용하여 기본 자료처리를 실시하고, 음향 임피던스 변환 모듈올 적용하여 동해 가스 하이드레이트 현장자료에 대한 광역 임피던스변화를 구하고 이로부터 음향 임피던스 단면도를 구하고자였다. 음향 임피던스 단면도는 중합단면도상에서 음향 임피던스 변화를 보여주고 있으며 특히 왕복주시 2.9초 전후에서 해저면 반사파와 위상이 반대이며 고진폭을 나타내는 해저면 기인 고진폭 반사층으로 여길만한 지점에서 그 변화가 크게 나타남을 알 수 있었다. 탄생파자료는 10 Hz 이하 저주파 정보가 들어있지 않아 완전한 음향 임피던스를 구할 수 없으므로 층서해석이 이루어진 중합 단면도부터 광역 임피던스를 구하였다. 향후 시추자료를 활용할 경우 좀더 정확한 음향 임피던스 단면도를 생산할 수 있을 것으로 여겨진다.
-
Gas hydrate has been attractive topic for two dedicates because it may cause the global warming, ocean hazards associated with the instability of marine slope due to the gas hydrate release as well as high potential of future energy resources. The study on gas hydrate in Ulleung basin has been performed since 1999 to explore the potential and distribution of gas hydrate offshore Korea. The numerous multi channel seismic data have been acquired and processed by Korea Institute of Geosciences and Mineral Resources (KIGAM). The results showed clearly the gas hydrate indicators such as pull up structure, bottom simulating reflector (BSR), seismic blanking zone. The prestack depth migration has been considered as fast and accurate technique to image the subsurface. In this paper, we will present both the conventional seismic data processing and apply Kirchhoff prestack depth migration for gas hydrate data set. The results will be applied for core sample collections and for proposal more detail 2D with long offset or 3D seismic exploration.
-
천연가스의 주요 구성성분은 메탄, 에탄, 프로판으로 99%이상 차지하고 있으며 천연가스 하이드레이트(NGH)는 압축천연가스(CNG)에 비해 체적당 질량이 크고 액화천연가스(LNG) 보다 상대적으로 유리한 온도 및 압력조건으로 인해 천연가스의 경제적인 저장 및 수송 수단으로 주목 받고 있다.
$CH_4$ -$C_2H_6$ ,$CH_4$ -$C_3H_8$ 혼합가스 하이드레이트의 제조시 반응시간에 따른 하이드레이트의 거동을 관찰하였으며 생성조건의 변화에 따른 하이드레이트의 생성속도를 비교하였다. 하이드레이트의 생성이 진행될 때 기상에서의$C_2H_6$ ,$C_3H_8$ 의 몰 비는 감소함을 보여주었고 이러한 변화는$CH_4$ -$C_3H_8$ 가$CH_4$ -$C_2H_6$ 보다 더욱 빠르게 진행되었다. 또한 생성된 하이드레이트의 해리과정이 진행될 때 역시 서로 다른 해리속도에 의해 조성의 변화를 관찰 할 수 있었다. -
가스 하이드레이트의 구조-I 및 구조-H의 공존 현상을 13C NMR과 Raman spectroscopy를 이용하여 분석하였다. 하이드레이트 생성 조건이 구조-H 영역에만 있을 때는 CH4+neohexane 혼합 하이드레이트가 구조-H만을 나타냈지만, 구조-I의 영역에서는 구조-H의 혼합 하이드레이트와 구조-I의 순수 메탄 하이드레이트가 공존하는 것을
$^{13}C$ NMR spectra를 통해 확인하였다. 이러한 현상은 구조-H 생성자로 알려진 isopentane, MCP, MCH 에서도 관찰되었으며, Raman spectroscopy를 이용해서도 확인할 수 있었다. -
Lee, Jong-Won;Lu, Hailong;Moudrakovski, Igor L.;Ratcliffe, Christopher I.;Ripmeester, John A. 577
분자 크기가 너무 커 가스 하이드레이트를 형성하지 않는다고 알려진 n-펜탄과 n-헥산이 다른 구조-H 형성 화합물과 혼합되어 사용될 경우 구조-H 동공 내에 함께 포접되는 것으로 확인되었다. 구조-H 하이드레이트의 형성 및 미세구조 분석은 고체 NMR 및 X-선 회절 분광법을 이용하여 확인하였다. 이러한 혼합 화합물에서 보이는 구조-H 하이드레이트 형성은 전체적인 구조-H 형성 화합물에서 나타나는 일반적 특징인 것으로 여겨진다. -
(HFC(hydrofluorocarbon, 수소불화탄소)는 오존층 파괴 지수가 낮기 때문에 CFC(chlorofluorocarbon)의 대체 물질로 냉매와 발포제로 널리 사용되고 있는 물질이다. 하지만 HFC는 지구온난화 지수가 높은 기체이므로 대기중으로 방출되는 것을 막기 위해 분리/회수하여 재활용하는 것이 중요하다. 본 연구에서는 공기와 HFC의 혼합기체로부터 HFC만을 분리해 내는 방법으로 가스 하이드레이트 형성법을 제안하였다. 이 방법의 열역학적 타당성을 검증하기 위하여 질소+HFC-134a 혼합기체에 대하여 275-285 K의 온도 범위와 1-27 bar의 압력범위에 걸쳐서 가스 하이드레이트 상평형을 측정하였다. 질소는 가스 하이드레이트를 형성하기 위하여 0
$^{\circ}C$ 에서 150 bar 이상의 높은 압력이 필요한 반면 HFC-134a는 대기압에 가까운 낮은 압력이 필요하다. 두 기체의 평형 압력의 차가 크다는 것은 가스 하이드레이트 형성법을 이용할 경우 기체의 분리 효율이 매우 높다는 것을 나타낸다. 그리고, 본 실험을 통해서 얻어진 혼합기체의 하이드레이트상(H)-액상($L_W$ )-기상(V)의 3상 평형선이 순수한 HFC-134a의 3상 평형선에 가깝게 위치하였다. 이는 가스 하이드레이트를 이용한 분리법이 낮은 압력에서 운전될 수 있음을 나타낸다. 이 분리법은 낮은 압력에서 운전되어 경제적일 뿐만 아니라 물 이외의 다른 매개체를 사용하지 않기 때문에 환경 친화적인 공정이라 할 수 있다. -
Gas hydrate is a special kind of inclusion compound that can be formed by capturing gas molecules to water lattice in high pressure and low temperature conditions. When referred to standard conditions,
$1m^3$ solid hydrates contain up to$172Nm^3$ of methane gas, depending on the pressure and temperature of production, Such large volumes make natural gas hydrates can be used to store and transport natural gas. In this study, three-phase equilibrium conditions for forming methane hydrate were theoretically obtained in aqueous single electrolyte solution containing 3wt% Nacl. The results show that Nacl acts as a inhibitor, but help gases such as ethan, propane, i-butane, and n-butane reduce the hydrate formation pressure at the same temperature. -
물을 함유한 공극 크기 6, 30, 100 nm의 실리카겔에 이산화탄소 및 메탄을 반응시켜 온도
$0{\sim}4$ $^{\circ}C$ , 압력$15{\sim}40$ bar 의 범위에서 가스 하이드레이트 생성속도를 측정하였다. 공극 크기가 작아짐에 따라 특정 온도에서의 평형압력이 높아지는 열역학적 특성을 감안하여 통일한 압력차 (평형압력과 실험압력의 차)를 얻을 수 있도록 조건을 설정하였다. 이산화탄소의 경우 통일 온도에서 하이드레이트 생성속도는 일반적으로 압력이 높아짐에 따라 가속되는 것을 알 수 있었다. 단위 물 당 포집되는 이산화탄소의 양은 최대 1.0을 넘지 못하였다. 또한 하이드레이트 생성을 위해 필요한 유도시간 (induction time)이 2내지 8시간 수준으로 매우 길었다. 공업적인 하이드레이트 이용을 위해서는 빠른 생성속도가 필요한 만큼 유도시간을 단축, 없애기 위해 계면활성제로 황산 도데실 나트륨 (sodium dodecyl sulphate)이 첨가된 수용액을 이용하였다. 계면활성제가 포함된 수용액에서의 하이드레이트 생성은 유도시간이 사라져 매우 빠르게 바뀌었고, 포집되는 이산화탄소도 15% 정도 증가되었다. 메탄의 경우에는 공극 크기가 작아질수록 하이드레이트 생성속도 및 가스 포집도가 저하되는 결과를 보였다. 이산화탄소의 경우와는 다르게 유도시간이 나타나지 않았으며 비교적 높은 가스 포집도를 얻기 위해서는 평형압력과 실험압력의 차이가 최소 2.0MPa 이상이어야 했다. -
Using an oedometer cell instrumented to measure the evolution of electromagnetic properties, small strain stiffness, and temperature, we conducted consolidation tests on four types of sediments. The tested specimens include sediments with different gas hydrate saturation at four stages of loading. The test results show that the electromagnetic and mechanical properties of hydrate-bearing marine sediments are governed by the vertical effective stress, stress history, porosity, hydrate saturation, fabric, ionic concentration of the pore fluid, and temperature. The results also show that permittivity and electrical conductivity data can be combined to estimate hydrate volume fraction in laboratory sediments, methodology that might eventually be extended for estimation of hydrate concentrations in field settings.
-
Studies on the hydrocarbons in shallow sediments of the East Sea of Korea have been carried out by the Korea Institute of Geoscience and Mineral Resources (KIGAM) since 2000. 4946 L-km of 2D multichannel reflection seismic data, 3250 L-km of high-resolution Chirp profiles and 16 selected piston cores were analyzed to determine the presence of hydrocarbons in shallow sediments of the western deep-water Ulleung Basin. The seismic data show a number of blanking zones that probably reflect widespread fluid and gas venting. The blanking zones are often associated with velocity pull-up structures. These upwelling structures are interpreted to be the result of high-velocity natural gas hydrate. There are also several bottom-simulating reflectors that are associated with free gas and probably overlying gas hydrate. Numerous pockmarks were also observed in the Chirp profiles. They are seafloor depressions caused by the removal of near-seafloor soft sediments by escaping of fluid and gas. In piston cores, cracks generally oriented parallel to bedding suggest significant gas content some of which may have been contained in gas hydrate in situ.
-
The co-combustion of coal and RPF(Refuse Plastic Fuel) mixture has been experimented in a commercially operating CFB coal boiler and the emissions such as SOx, NOx, TSP and dioxine were measured at the stack. The experimented RPF was supplied by domestic RPF company that is commercially producing RPF pellet from the wasted plastics. Up to 15% of total coal was substituted to RPF and no trouble was happened during normal boiler operation. SOx and NOx concentration was reduced about
$15{\sim}20$ % and TSP(Total Suspended Particle) was drastically reduced about 30% during co-combustion. Dioxine concentration at mixing ratio of 7.5% was$0.0487ng{\sim}TEQ/Sm^3$ ($O_2$ , 12%) that satisfied governmental emission regulation. -
A pilot scale circulating fluidized bed for refuse derived fuel is developed and constructed in order to demonstrate efficient and safe utilization of waste fuel. The capacity of the facility is 8 steam tons per hour with the steam quality of
$450^{\circ}C$ and 38atm. The quantity and the quality of the produced steam is sufficient to produce 1MWe power capacity. The test operation proved the high combustion efficiency of 99% and up. The emissions of NOx, SOx in flue gas are below 100, 60ppm respectively with out any emission control. HCl emissions were above 400ppm at the combustor exit but reduced below 10ppm after scrubber. -
Nho, Nam-Sun;Kim, Kwang-Ho;Jeon, Sang-Goo;Shin, Dae-Hyun;Lee, Kyong-Hwan;Kim, Hyoung-Hoon;Park, Hyo-Nam 617
-
This paper provides RPF (Refuse Plastics Fuel) gasification characteristics for generating synthesis gas in gasfying reactor which was design in lab-scale. This research is carried out as an immediate work for making pyrolysis gas from RPF into energy resource. This study is consisted of experimental and numerical. The numerical study was accomplished from RPF pyrolysis data, and predicted the maximum operating conditions by STANJAN and FLEUNT. Based on results of STANJAN, it is found that the maximum point of
$O_2/O_{2,stoich}$ =20${\sim}$ 30, which is used as injection point of$O_2$ . Experiment results shows that CO and$H_2$ were increased but THC was decreased as temperature was increased. It is estimated that the cracking of cracking of THC into CO and H2 is happened at a high temperature. It is observed that as steam was injected, production of CO and H2 were increased, then, H2 is dependent on the amount of injectionsteam. -
킬른형 열분해 반응기를 이용하여 혼합폐플라스틱의 열분해로부터 얻어진 고분자성분의 열적분해 특성에 관한 연구를 TGA와 GC-MS를 이용하여 수행하였다. 열적분해의 속도론적 연구는
$10{\sim}50^{\circ}C/min$ 사이의 여러 가열속도에서 비등온 질량감소 기술을 이용하여 수행하였으며 활성화 에너지 및 반응 차수와 같은 속도 상수들에 대한 정보를 얻기 위하여 문헌에 제시된 여러 가지의 속도론 해석방법을 이용하여 질량감소곡선 및 그 미분 값을 해석하였다. 또한 회분식 열분해 반응기를 이용하여 반응온도에 따른 액상 생성물의 수율변화를 고찰하였으며 GC-MS를 이용하여 액상 생성물의 반응온도 증가에 따른 특성연구를 수행하였다. -
폐기물의 플라즈마를 이용한 열분해-가스화-용융 처리공정은 청정연료 형태로 정화된 합성가스를 얻을 수 있고, 이 합성가스를 WGS 반응과 PSA 공법을 이용하면 고순도 수소로의 전환 및 회수가 가능하다. (주)애드플라텍에서는 자체 보유하고 있는 3톤/일급 플라즈마 폐기물 처리설비와 수소 정제/회수시스템을 연계하여, 폐기물로부터 고순도 수소 생산 (
$20Nm^3/h$ 이상)을 위한 플라즈마 폐기물 처리 수소 생산 통합시스템 개발을 진행하고 있다. 합성가스 내 질소 농도를 낮추기 위해 산소를 매질로 하는 100kW급 산소 플라즈마 토치를 제작 하였다. 수소 정제/회수 시스템은 폐기물의 플라즈마 처리 후의 합성가스 생성량과 조성의 변화에 대응할 수 있도록 하였으며 WGS 반응기로 들어가는 합성가스를 가스 컴프레서를 통하여 최대 10기압으로 승압시키고, 고농도 일산화탄소의 효과적인 제거 및 열 회수 극대화가 이루어질 수 있는 최적의 가스처리 시스템으로 구현되도록 하였다. 설치 완료된 WGS 반응기의 성능시험이 플라즈마 처리설비와 연계하여 수행되었으며 WGS 반응기를 거친 일산화탄소의 농도는 1.5% 미만으로 분석되었다. 차기 년도에 설치/가동 예정인 수소 생산용 PSA는 최대 10기압 운전 및 상압재생 방식으로 운전되며 생산된 수소는 최소 99.99%이상의 고순도를 유지할 것으로 기대된다. -
국내에서 발생되는 폐기물을 이용하여 가스화에 의해 생산되는 합성가스의 생산 및 활용기술에 대해 고찰하였다. 폐기물 가스화에 의해 생산되는 합성가스의 조성은 CO,
$H_2$ 를 주성분으로 하며 부분산화 조건에$CO_2$ 가 함께 생산된다. 생산된 합성가스는 CO$20{\sim}35$ %,$H_{2}$ $20{\sim}35$ % 정도의 조성으로 나타나며 발생량은$1,365{\sim}2,125$ $Nm^3/hr$ 로 나타났다. 이러한 합성가스는 스팀생산, 전력생산 및 DME, SNG, 메탄올, 수소와 같은 고부가가치의 화학원료를 생산할 수 있다. -
화석연료의 고갈이 가시화됨에 따라 이를 해결하기 위한 대체에너지원의 확보를 위해 다양한 연구가 수행되어 왔다. 본 연구에서는 폐기물 특히 플라스틱 폐기물의 안정적인 처리 및 청정가스의 생산방법을 연구하기 위해서 선행적으로 플라스틱 폐기물의 열분해 특성을 조사하였으며, 그 반응모델을 제시하여 열분해로의 설계인자의 도출하고자 하였다. 대상 폐 플라스틱류로서 PE, PP, PVC, RPF 등을 이용하였고, 열중량분석기와 tube furnace를 통해서 온도에 따른 분해반응 특성을 확인하였다. 열분해 특성조사를 한 결과 PE, PP 등은 잔류 char가 없이
$400^{\circ}C$ 전후에서 완전 분해하였으며, PVC의 경우$400^{\circ}C$ 이후에도 약 20% 이상의 char가 잔류함을 확인하였고, RPF의 경우에도 약 10%의 char이 잔류함을 확인하였다. 또한 각각의 열분해 특성을 DTG/TGA분석을 통해서 적정체류시간을 구할 수 있었고, 다단열분해 가스화기를 이용하여 합성가스를 제조한 결과 2500 kcal /$Nm^3$ 의 높은 발열량을 가진 합성가스를 제조할 수 있었다. -
석탄, 폐기물 등 다양한 시료의 가스화 반응을 통해서 발생되는 합성가스는 CO,
$H_2$ ,$CO_2$ 가 주성분으로 가스엔진, 가스터빈 등의 연료로 사용하여 발전하거나 합성반응을 통해 다양한 화학원료로의 전환이 가능하다. 합성가스를 가스엔진, 가스터빈, 연료전지등의 연료로 사용하는 경우는 고효율 발전이 가능하여 기존 연소방식의 발전과 비교하여 단위 전력 생산량 당$CO_2$ 의 배출량이 감소 되며, 여기에$CO_2$ 분리공정을 적용하면$CO_2$ 배출량 감소효과를 극대화 할 수 있다. 화석연료의 연소 및 가스화 반응을 통해서 발생하는 이산화탄소의 분리에 대한 많은 연구가 진행되고 있으나, 본 연구에서는 흡착방식을 이용한 합성가스 내의 이산화탄소 분리를 위하여 흡착제를 이용한 이산화탄소의 흡착, 탈착 성능 분석 연구를 수행하였다. 합성가스내의 이산화탄소를 분리하기 위한 흡착제로는 NaX 계열의 zeolite를 이용하였으며, 가스화 반응을 통해 발생한 합성가스를 흡착제에 통과시켜 이산화탄소의 선택적 흡착 여부를 확인하였다. 또한 TPD(Temperature Programmed Desorption)방법을 이용하여 흡착제의 이산화탄소 흡착 성능을 분석하였다. -
Yim, Eui-Soon;Min, Kyung-Il;Jeon, Cheol-Hwan;Lee, Don-Min;Kim, Jong-Ryeol;Kim, Seung-Soo;Jang, Eun-Jung;Park, Cheon-Kyu;Jung, Chung-Sub;Kim, Jae-Kon;Lim, Young-Kwan;Shin, Seong-Cheol 649
국제 원유가의 지속적인 상승에 따라 화석연료 고갈을 대비한 대체에너지 빛 온실가스배출감소를 위하여 바이오연료의 사용 및 상용보급은 전세계적인 추세이다. 우리나라의 경우 바이오디젤은 2002년부터 시범보급사업(Demonstration & dissemination)을 거쳐 2006년 7월부터 전국주유소를 통하여 경유 중에 바이오디젤 0.5%를 혼합한 BDO.5를 수송용 연료로 도입하여 아시아 최초로 상용보급화를 시행하고 있다. 또한 휘발유 중 바이오에탄올 혼합 연료유 도입을 위한 실증평가연구를 2006년 8월부터 2008년 7월까지 수행중이다. 자동차용 휘발유의 옥탄가 향상을 위해 함산소 기재로 사용되는 MTBE(Methyl Tertiary Butyl Ether)를 바이오에탄올로 대체한 바이오에탄올 혼합연료유는 수분 혼입에 의한 상 분리(Phase separation)와 금속에 대한 부식성 문제를 야기 시킬 수 있다. 바이오에탄올을 서브옥탄가솔린(Sub-octane gasoline)에 혼합하여 상 분리 모사실험, 금속류 부식시험, 고무류 침지실험 등 다양한 품질특성평가를 수행하였으며, 이런 결과들을 바탕으로 국내실정에 알맞은 최적의 혼합량(E3, E5)을 도출하였다. 또한 전국에 4개 시범주유소를 운영하여 바이오에탄올 혼합 연료유의 유통 및 보급을 통해 최적의 유통인프라(Distribution infrastructure) 보완 및 구축 방안을 도출 하고자 한다. -
본 연구에서는 수송부문 온실가스 저감 대책으로 수송용 바이오에탄올을 국내 수송시장에 도입한 형태에 대해 살펴보았다. 바이오에탄올의 경우 'Carbon Neutral' 한 특성에 따라 친환경연료로써의 이점이 크나 원재료를 수입해야하고, 또 정부정책방향에 따라 경제성이 좌우된다. 분석결과, E5를 도입하여 저감잠재량을 분석했을 때 기존 휘발유 수요전망보다 연간 15억
$CO_2kg/yr$ 정도의 감축이 가능한 것으로 나타난다. 비용분석 결과 현재 휘발유에 부과하는 규모와 같은 정도의 세금이 부과한 바이오에탄올 공급가격은 1639.2원이다. 이는 휘발유 판매 가격인 1448.5에 비해 경쟁력이 없으나 바이오에탄올이 CDM 사업으로 인정받아 CERs 수익을 얻을 수 있는 경우의 공급가격은 1583.5원으로 배출권 수익을 포함하지 않았을 때보다 50원 정도의 추가 수익을 발생함을 확인하였다. 이는 바이오에탄올의 면세범위를 줄임으로써 납세자의 세금을 통한 사업자에 대한 과도한 지원을 지양할 수 있는 적정한 정부지원정책 방법으로 고려될 수 있을 것이다. -
It was investigated on this paper that the status of biomass energy utilization in the registered CDM projects. The ratio of the case including the energy recovery among the registered biomass CDM projects is just about 57%. Direct thermal conversion technology is the most commonly applied for biomass energy recovery projects. Through the comparative study with world renewable energy outlook, the contribution of CDM to biomass energy supply in the world is not considerable yet.
-
Since biomass is given the status of "renewable resource" in contrast to "exhaustible resource" e.q., fossil fuels, it plays a significant role in the sustainable development in future. We installed a downdraft gasifier for power generation from biomass materials. The biomass raw materials were wood chips with a moisture content of 18-23 wt.%, supplied at 40-50kg/h. This paper describes on the optimum gasification air ratio that is defined as the ratio of the oxygen mole supplied into the gasifier to the oxygen mole required for complete combustion for producing syngas supplied into a gas engine. The results showed that, lower heating value of the syngas was 1200
$kcal/m^3$ $_N-dry$ and cold gas efficiency of the gasification system was 72% under optimum operating conditions. -
에너지 사용량의 증가와 국제적인 환경 규제에 대응하기 위하여 환경친화적인 연료의 개발이 시급한 가운데 재생가능한 동식물성 유지로부터 생산되는 바이오 디젤에 대한 연구가 활발히 진행되고 있다. 특히 자원 재활용 및 에너지 생산관점에서 폐식용유로부터 바이오디젤 원료로 사용하는 연구가 활발히 진행되어 왔다. 이러한 폐식용유를 이용한 바이오디젤 생산에서 폐식용유내 함유된 유리지방산 및 수분에 의해 효율적인 전이에스테르화 반응이 어렵기 때문에 이를 전처리 단계에서 제거되어야 한다. 본 연구에서는 폐식용유내 유리지방산을 효과적으로 제거하기 위하여 회분식 반응기에서 MFI 제올라이트 촉매를 이용하여 Si/Al 몰비에 따른 산세기 및 산량의 변화에 따른 유리지방산 제거 특성을 조사해 보았다.
-
-
교토의정서의 발효로 인해 전세계적으로 온실가스 감축 활동이 활발하게 진행되고 있으며, 국내 산업계 또한 온실가스 저감을 피할 수 없게 되었다. 특히 교토의정서 이행을 위해 도입된 교토메카니즘 가운데 개발도상국의 온실가스 감축 활동을 위해 CDM 사업이 활성화되고 있으며, 개발도상국인 우리나라도 참여할 수 있기 때문에 국내 기업 및 정부의 관심이 높아지고 있다. 그러나 CDM 사업을 수행하기 위해서는 적용 가능한 CDM 사업 방법론이 필요하며, 방법론이 없을 경우 CDM 사업 방법론을 개발하여야 한다. 방법론에는 베이스라인, 추가성, 배출 감축량 등에 대한 구체적인 방법이 제시되어야 하고 사업의 타당성 확인 및 검증을 위해 방법론을 정확히 이해해야 한다. 따라서 본 CDM 사업 방법론 연구를 통해 CDM 사업 수행 및 방법론 개발을 위해 필요한 주요 항목에 대한 이해를 돕고 국내 CDM 사업의 활성화를 도모하고자 한다.
-
-
Now Korea depends upon the imported resources for about 97% of total using energy. So from October, 2001 Korean government has supported renewable energy business owners by providing them with Electric Power Industry Basis Fund. Only plant-use electricity of the small hydro power plant is exactly managed, but other renewable energy plants is unprepared or not yet managed. Therefore, in this paper, we'll analyze the plant-use electricity management of the small hydro power and propose improvement plans for plant-use electricity of the photovoltaic power plant.
-
신
${\cdot}$ 재생에너지 발전차액 지원이 전력기반기금을 통해 우선 지원됨에 따라 지원금의 규모가 현재의 제도 하에서 지속가능할 것인가에 대한 문제가 지적되어 왔다. 본 연구는 새로운 기준가격지침에 따라 발전차액지원금의 규모를 추정하여 본 결과, 현재와 같이 SMP가격이 지속적으로 상승하는 경우에는 전력산업기반 기금 중 차액지원금의 비중이 2011년에$8.96%{\sim}21.49%$ 수준으로 도출되어 다소 비중은 증가하지만 관련 사업의 지원에 큰 무리는 없으며, 이전의 연구결과에 따른 지원규모의 폭등현상 등은 나타나지 않을 것으로 분석되었다. -
점차 심화되고 있는 북한의 에너지 위기는 북한 사회이 경제적 측면뿐만 아니라 사회 및 정치, 나아가서는 국제 사회에서의 북한의 외교정책에까지 영향을 미치는 것은 물론 남한의 군사적, 정치적 위협 요인이 되고 있다. 북한의 에너지난 타개를 위해 여러 회담의 주요 사안으로 에너지 지원을 요구하고 있으며, 내부적으로는 에너지 공급 제한 등의 정책을 시행하고 있으나 이는 미봉책에 불과하다. KEDO 중단으로 북한의 장기적 에너지 지원 노력이 중단되었으며, 중유 지원 등의 방식은 일시적인 수준에서 그치게 될 것 이다. 본 연구에서는 북한의 에너지난을 타개하고 이를 통하여 사회 경제 전반의 안정화에 기여할 수 있는 대북 에너지 지원 방안을 모색하고자 한다.
-
The R&D budget of energy technology development has increased in the sector of Korean energy technology development continuously. In addition to that, KIER, the government invested research institute and unique energy technology R&D research institute, is trying to plan for a big-sized energy R&D program for the well focused R&D and excellent research outcomes. In the phase of R&D process, the planning is one of the most important sectors because it drives the direction of R&D. In this study, we suggest the assessment criteria to select a strategic energy technology R&D programs by the analytic hierarchy process, which is one of multi-criteria decision making method (MCDM). We structure 2 tiers of hierarchy for assessing a big-sized R&D program and also establish 6 criteria in the level 1, which are energy environment, economic spin-off, technical spin-off, marketability, KIER mission, and cost. We allocate the relative weights of criteria by checking the values of consistency ratio as making pairwise comparisons. The result of this research will provide the decision makers as they select a right well focused R&D program.
-
Six thousands of vehicles are operated on Korean urban transit system. 95% of them have regeneration system. Especially, the VVVF-Inverter vehicle has a merit of the highest regeneration rate. Therefore, the energy storage system is needed to be developed to use regeneration energy when the vehicle is braking. Therefore, Measuring regeneration energy in the substation need to know how much regeneration energy occurs, how much capacity of energy storage system is needed. After measuring regeneration energy, we design the capacity of energy storage system.