• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.3
• /
• pp.485-491
• /
• 2015

This paper shows the design improvement and test model of FAU (Frequency Analysis Unit) in PDD (Partial Discharge Diagnosis system) for 800kV GIS (Gas Insulated Switchgear). We found some problems during operation of previous FAU, such as the aging of fiber-optic converter that can cause communication error, the malfunction of signal analysis circuit etc. And then we solved those problems by design improvement and verified the performance through type test. To monitor partial discharge, the performance of UHF sensor is important but the performance of frequency analysis unit is also very important. So we solved communication error, the malfunction of signal analysis circuit and then increased the operation reliability of FAU by improving fiber-optic converter and signal analysis circuit. Accredited testing laboratory carried out the performance verification test according to performance test criteria and procedure of reliability test standards, IEC-60225, 61000 and 60068 etc. We confirmed the test results which correspond with the performance test criteria.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.162-168
• /
• 2005

In this paper, a digital current mode control is designed for the power converter applications. The designed digital current mode controller is derived analytically from the continuous time small signal model of the power converters. Due to the small signal model based derivations of the control law, the designed control method can be applicable to boost, buck, and buck-boost converters. It is also proven that the controlled power converter employing the designed digital current mode controller is always stable regardless of an operating conditions. In order to show the usefulness of a designed controller, experiments are carried out using a 16bit DSP micro-processor, TMS320LF2406A.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2000.12a
• /
• pp.149-152
• /
• 2000

A scanner is an output device that scans documents, photographs, films etc, and convert them to digital data. Especially, a film scanner is used for scanning negative/positive films. In this paper, we design step motor control part, image sensor part, and Aか converter part which are components of the scanner and use DSP for fast signal processing. We also design the interface circuits using EPLD between these peripherals and DSP. The PC interface circuits between scanner and PC are designed by using parallel port to control and transfer the scanned data from scanner to PC. For 35mm film, we design hardwares which obtain high resolution more than 9 million pixels (horizontal resolution is 3835 and vertical resolution is 2592).

• Journal of Power Electronics
• /
• v.18 no.5
• /
• pp.1595-1607
• /
• 2018

In this paper, a hierarchical control strategy is introduced to control a new three-port multidirectional DC-DC converter for integrating an energy storage system (ESS) to a bipolar DC microgrid (BPDCMG). The proposed converter provides a voltage-balancing function for the BPDCMG and adjusts the states of charge (SoC) of the ESS. Previous studies tend to balance the voltage of the BPDCMG buses with active sources or by transferring power from one bus to another. Furthermore, the batteries available in BPDCMGs were charged equally by both buses. However, this power sharing method does not guarantee efficient operation of the whole system. In order to achieve a higher efficiency and lower energy losses, a triple-layer hierarchical control strategy, including a primary droop controller, a secondary voltage restoration controller and a tertiary optimization controller are proposed. Thanks to the multi-functional operation of the proposed converter, its conversion stages are reduced. Furthermore, the efficiency and weight of the system are both improved. Therefore, this converter has a significant capability to be used in portable BPDCMGs such as electric DC ships. The converter modes are analyzed and small-signal models of the converter are extracted. Comprehensive simulation studies are carried out and a BPDCMG laboratory setup is implemented in order to validate the effectiveness of the proposed converter and its hierarchical control strategy. Simulation and experimental results show that using the proposed converter mitigates voltage imbalances. As a result, the system efficiency is improved by using the hierarchical optimal power flow control.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.3
• /
• pp.152-162
• /
• 2003

In this paper, Binary to Quaternary Converter(BQC), Quaternary to Binary Converter(QBC) and Quaternary inverter circuit, which is the basic logic gate, have been proposed based on voltage mode. The BQC converts the two bit input binary signals to one digit quaternary output signal. The QBC converts the one digit quaternary input signal to two bit binary output signals. And two circuits consist of Down-literal circuit(DLC) and combinational logic block(CLC). In the implementation of quaternary inverter circuit, DLC is used for reference voltage generation and control signal, only switch part is implemented with conventional MOS transistors. The proposed circuits are simulated in 0.35 ${\mu}{\textrm}{m}$ N-well doubly-poly four-metal CMOS technology with a single +3V supply voltage. Simulation results of these circuit show 250MHz sampling rate, 0.6mW power consumption and maintain output voltage level in 0.1V.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.770-776
• /
• 2009

We propose and demonstrate an I/Q demodulator using four-port BPSK demodulator base on additive mixing and reflection-type phase shifter using hybrid technique. Previously, the conventional I/Q demodulator base on multiplicative or additive mixing method divides I/Q signal path from mixer to parallel-to-serial converter. In this paper, we propose new I/Q demodulator without dividing I/Q baseband signal path. The proposed schematic requires half size in implementation and half power consumption in baseband path compared with the conventional receiver. Also, the proposed receiver eliminates parallel-to-serial converter after data decoding. The proposed circuit has been successfully demodulated a QPSK signal with the L-band carrier frequency and 20 Mbps data rate.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.12
• /
• pp.22-28
• /
• 2008

This paper designed a efficient 8-bit CMOS analog-to-digital converter(ADC) for an SOC(System On Chip) application. The architecture consists of two modified 4-bit full-flash ADCs, it has been designed using a more efficient architecture. This is to predict roughly the range in which input signal residers and can be placed in the proximity of input signal based on initial prediction. The prediction of input signal is made available by introducing a voltage estimator. For 4-bit resolution, the modified full-flash ADC need only 6 comparators. So a 8-bit ADC require only 12 comparators and 32 resistors. The speed of this ADC is almost similar to conventional full-flash ADC, but the die area consumption is much less due to reduce numbers of comparators and registors. This architecture uses even fewer comparator than half-flash ADC. The circuits which are implemented in this paper is simulated with LT SPICE tool of computer.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1218-1221
• /
• 2018

This paper presents a low-power 0.6-V 10-bit 200-kS/s double rail-to-rail successive approximation register (SAR) analog-to-digital converter (ADC). The proposed scheme allows input signal with 4 times power which is compared with conventional one by applying proposed rail-to-rail scheme, and that improves signal-to-noise ratio(SNR) of NTV SAR ADCs. The prototype was designed using 65-nm CMOS technology. At a 0.6-V supply and $2.4-V_{pp}$ (differential) and 200-kS/s, the ADC achieves an SNDR of 59.87 dB and consumes 364.5-nW. The ADC core occupies an active area of only $84{\times}100{\mu}m^2$.

• The Journal of Korea Robotics Society
• /
• v.2 no.3
• /
• pp.205-211
• /
• 2007

In this paper, the prototype of surface EMG (ElectroMyoGram) sensor is developed for the robotic rehabilitation applications, and the developed sensor is composed of the electrodes, analog signal amplifiers, analog filters, ADC (analog to digital converter), and DSP (digital signal processor) for coding the application example. Since the raw EMG signal is very low voltage, it is amplified by about one thousand times. The artifacts of amplified EMG signal are removed by using the band-pass filter. Also, the processed analog EMG signal is converted into the digital form by using ADC embedded in DSP. The developed sensor shows approximately the linear characteristics between the amplitude values of the sensor signals measured from the biceps brachii of human upper arm and the joint angles of human elbow. Finally, to show the performance of the developed EMG sensor, we suggest the application example about the real-time human elbow motion acquisition by using the developed sensor.

• Journal of Semiconductor Engineering
• /
• v.1 no.2
• /
• pp.64-73
• /
• 2020

As CMOS technology scales down, the design of analog signal processing circuit becomes far more difficult because of steadily decreasing supply voltage and smaller intrinsic gain of transistors. With sub-1V supply voltage, the conventional analog signal processing relying on high-gain amplifiers is not an effective solution and different approach has to be sought. One of the promising approaches is "time-domain analog signal processing" which exploits the improving switching speed of transistors in a scaled CMOS technology. In this paper, various time-domain analog signal processing techniques are explained with some experimental results.