• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.6
• /
• pp.90-95
• /
• 1997

In designing a resonant circuit of the inverter which puts induction heating with high frequency to the load, an inductance L of the circuit, the coupling coefficient of a transformer transfering the output power to load, and the coupling coefficient of load circuit heating with coil affect to the output power of a resonant circuit, the circuit Q and the frequency. Those characteristics of the circuit are analyzed through Thevenan's equivalent circuit of the coupling coefficient type which is derived from the T-type equivalent circuit of a transformer. On this equivalent circuit, the impedance of a transformer referred to its primary side is not only proportional the square of turn ratio, nZ, but also the square of coupling coefficient, K2 This paper proposed a more accurate fundamental method to design a resonant circuit of the inverter by using the Thevenan's equivalent circuit.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.16-20
• /
• 2004

We present the fabrication and performance of wavelength tunable butt coupled (BT) sampled-grating (SG) distributed bragg reflector (DBR) - planar buried heterostructure (PBH) laser diodes (LD). The fabricated LD showed the high optical output power due to the high coupling efficiency between active and passive components by the BT coupling methods. The series resistance and diode ideality factor of LD were measured to be 3.7 $\Omega$ and 1.35, respectively. The average threshold current was 25 ㎃. The output powers of BT-SG DBR-PBH-LD were obtained to be as high as 12.3 and 24.56 ㎽ at 100 and 200 ㎃, respectively. The maximum wavelength tuning range was about 31 nm and the side mode suppression ratio was about 37 dB.

• Journal of KSNVE
• /
• v.10 no.5
• /
• pp.880-885
• /
• 2000

In a verical type, vibratory gyroscope, the coupled motion between the reference and sensing vibrations causes the zero-point output which means non-zero sensing vibration without angular velocity. This structural coupling leaks to an inherent discrepancy between the natural frequencies of the reference and sensing oscillations, causing the degradation of the sensing performance and dynamic stability. In this paper, the dynamic characteristics associated the coupling phenomenon are theoretically analyzed. Effects of reference frequency and coupling factor on the rotational direction and amplitude of elliptic oscillation are studied. A technique to predict the existence of curve veering of crossing in frequency trajectories is introduced to apply the design of micro gyroscopes with decoupled structures.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.5
• /
• pp.100-107
• /
• 2000

The hydraulic couplings have been widely used in industries, automobile, and power-station drives including ships. A mathematical analysis by which the design and application of hydraulic couplings are made is used in conventional design formulae and general roto-dynamic theories. The fluid flow of hydraulic couplings can be considered to have two component, one circumferentially about the coupling axis, and the other passing fluid from the pump to the turbine in the plane of the coupling axis. Tests have been carried out on the full-scale production coupling. The performance test consists of taking measurement of torque of the fluid coupling for three different amount of working fluid inside with various loads to the output shaft. The purpose of this research is to construct the experimental test equipments and to establish a series of performance test for the domestically developed hydraulic couplings, and to obtain experimental results which can be used to improve the performance of the hydraulic coupling and to solve the practical problems confronted in operation.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.613-615
• /
• 1996

Harmonic elimination method of using coupling transformer in twelve pulse inverter is presented for high power application. This method is using coupling transformer and PWM(pulse width modulation) switching and voltage source inverter. The object of proposed harmonic elimination method is obtained inverter output of low THD(Total Harmonic Distortion). The simulation results confirm the proposed harmonic elimination method.

• Journal of Information Display
• /
• v.11 no.1
• /
• pp.21-23
• /
• 2010

A new level shifter using low-temperature polycrystalline silicon (poly-Si) thin-film transistors (TFTs) for low-power applications is proposed. The proposed level shifter uses a capacitive-coupling effect and can reduce the power consumption owing to its no-short-circuit current. Its power saving over the conventional level shifter is 72% for a 3.3 V input and a 10 V output.

• Korean Journal of Optics and Photonics
• /
• v.25 no.2
• /
• pp.61-66
• /
• 2014

We report the characterization of a wavelength-swept laser (WSL) using a polygon-based wavelength scanning filter and two semiconductor optical amplifiers (SOAs). The output intensity and scanning bandwidth of the WSL depend on the position of the two SOAs in the laser cavity and the coupling ratio of the output fiber coupler. The outputs of the WSL are characterized for coupling ratios of 10%, 30%, 50%, 70%, and 90% for the output fiber coupler. In the setup in which the output fiber coupler is located between the two SOAs, high output power and wide scanning bandwidth can be achieved with an optimized configuration. Using the optimized configuration of the WSL, the intensity increases with the coupling ratio. These results can be used to construct an optimized WSL using the polygon-based wavelength scanning filter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.3
• /
• pp.208-216
• /
• 2018

In this paper, an LLC resonant converter employing two coupled inductors on the secondary side of the converter is proposed. The conventional LLC converter exhibits serious power loss during secondary winding of the transformer because of generation of tremendous output current ripples. To overcome this problem, an LLC resonant converter with a current doubler as a rectifying circuit was recently proposed. However, the current-doubler rectifying circuit requires coupled inductors with a high coupling ratio to retain the designed resonance characteristics. Therefore, an additional hardware filter is required at the output stage to address large output current ripples. Additional design procedures are also necessary because the inductance component of the added filter affects the designed resonant network. To solve this issue, an LLC resonant converter employing two coupled inductors is proposed in this paper. Mathematical analysis shows that the proposed secondary-side current-doubler circuit does not affect the designed resonance characteristics. The operating principles and theoretical analyses are proven through a simulation and experiments with a 54 V/28 A prototype.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.15 no.1
• /
• pp.24-29
• /
• 2005

In the fuzzy control for the multi-variable system, it is difficult to obtain the fuzzy rule. Therefore, the parallel structure of the independent single input-single output fuzzy controller using a pairing between the input and output variable is applied to the multi-variable system. However, among the input/output variables which arc not paired the interactive effects should be taken into account. these mutual coupling of variables affect the control performance. Therefore, for the control system with a strong coupling property, the control performance is sometimes lowered. In this paper, the effect of mutual coupling of variables is considered by the introduction of a neuro-fuzzy controller using relative gain matrix. This proposed neuro-fuzzy controller automatically adjusts the mutual coupling weight between variables using a neural network which is realized by back-propagation algorithm. The good performance of the proposed nero-fuzzy controller is verified through computer simulations on 200MW boiler systems.

• Journal of Sensor Science and Technology
• /
• v.29 no.3
• /
• pp.172-179
• /
• 2020

We studied an integrated-optic biosensor configuration that operates at a wavelength of 0.63 ㎛ based on the evanescent-wave and two horizontal mode power coupling of Si₃N₄ rib-optical waveguides formed on a Si/SiO₂/Si₃N₄/SiO₂ multilayer thin films. The sensor consists of a single-mode input waveguide, followed by a two-mode section which acts as the sensing region, and a Y-branch output for separating the two output waveguides. The coupling between the two propagating modes in the sensing region produces a periodically repeated optical power exchanges along the propagation. A light power was steered from one output channel to the other due to the change in the cladding layer (bio-material) refractive index, which affected the effective refractive index (phase-shift) of two modes through evanescent-wave. Waveguide analyses based on the rib optical waveguide dimensions were performed using various numerical computational software. Sensitivity values of 12~23 and 65~165 au/RIU, respectively for the width and length of 4 ㎛, and 3841.46 and 26250 ㎛ of the two-mode region corresponding to the refractive index range 1.36~1.43 and 1.398~1.41, respectively, were obtained.