• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.3-4
• /
• 2006

본 논문에서는 nano-scale CMOSFET을 위해 Boron Cluster ($B_{18}H_{22}$)가 이온주입된 SOI 와 Bulk 기판들 이용하였으며 실리사이드의 열 안정성 개선을 위해 Ni-V을 증착한 것과 순수 Ni을 증착한 것을 비교 분석 하였다. 결과 SOI위에 Ni-V을 증착한 것이 제일 낮은 면 저항을 보여주었고 반대로 Bulk위에는 제일 높은 면 저항을 보여 주었다. 단면을 측정한 결과 SOI 위에 Ni-V을 증착한 동일 조건의 Ni보다 Silicide의 두께가 두껍게 형성된 것을 확인하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.1001-1006
• /
• 2005

A new fabrication method is proposed to form the stacked polysilicon gate by nitridation in $N_2$ atmosphere using conventional LP-CVD system. Two step stacked layers with an amorphous layer on top of a polycrystalline layer as well as three step stacked layers with polycrystalline films were fabricated using the proposed method. SIMS profile showed that the proposed method would successfully create the nitrogen-rich layers between the stacked polysilicon layers, thus resulting in effective retardation of dopant diffusion. It was observed that the dopants in stacked films were piled-up at the interface. TEM image also showed clear distinction of stacked layers, their plane grain size and grain mismatch at interface layers. Therefore, the number of stacked polysilicon layers with different crystalline structures, interface position and crystal phase can be easily controlled to improve the device performance and reliability without any negative effects in nano-scale CMOSFETs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.57-63
• /
• 2008

In this paper, the dependence of MOSFET performance on the channel stress is characterized in depth. The tensile and compressive stresses are applied to CMOSFET using a nitride film which is used for the contact etch stop layer (CESL). Drain current of NMOS and PMOS is increased by inducing tensile and compressive stress, respectively, due to the increased mobility as well known. In case of NMOS with tensile stress, both decrease of the back scattering ratio ($\tau_{sat}$) and increase of the thermal injection velocity ($V_{inj}$) contribute the increase of mobility. It is also shown that the decrease of the $\tau_{sat}$ is due to the decrease of the mean free path ($\lambda_O$). On the other hand, the mobility improvement of PMOS with compressive stress is analyzed to be only due to the so increased $V_{inj}$ because the back scattering ratio is increased by the compressive stress. Therefore it was confirmed that the device performance has a strong dependency on the channel back scattering of the inversion layer and thermal injection velocity at the source side and NMOS and PMOS have different dependency on them.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.10-10
• /
• 2008

Silicide is inevitable for CMOSFETs to reduce RC delay by reducing the sheet resistance of gate and source/drain regions. Ni-silicide is a promising material which can be used for the 65nm CMOS technologies. Ni-silicide was proposed in order to make up for the weak points of Co-silicide and Ti-silicide, such as the high consumption of silicon and the line width limitation. Low resistivity NiSi can be formed at low temperature ($\sim500^{\circ}C$) with only one-step heat treat. Ni silicide also has less dependence of sheet resistance on line width and less consumption of silicon because of low resistivity NiSi phase. However, the low thermal stability of the Ni-silicide is a major problem for the post process implementation, such as metalization or ILD(inter layer dielectric) process, that is, it is crucial to prevent both the agglomeration of mono-silicide and its transformation into $NiSi_2$. To solve the thermal immune problem of Ni-silicide, various studies, such as capping layer and inter layer, have been worked. In this paper, the Ni-silicide utilizing Pd stacked layer (Pd/Ni/TiN) was studied for highly thermal immune nano-scale CMOSFETs technology. The proposed structure was compared with NiITiN structure and showed much better thermal stability than Ni/TiN.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.23-28
• /
• 2010

In this paper, comparative analysis of digital and analog performances of strained-silicon PMOSFETs with different carrier direction were performed. ID.SAT vs. ID.OFF and output resistance, Rout performances of devices with <100> carrier direction were better than those of <110> direction due to the greater carrier mobility of <100> channel direction. However, on the contrary, NBTI reliability and device matching characteristics of device with <100> carrier direction were worse than those with <110> carrier direction. Therefore, simultaneous consideration of analog and reliability characteristics as well as DC device performance is highly necessary when developing mobility enhancement technology using the different carrier direction for nano-scale CMOSFETs.