• 대한전자공학회논문지SD
• /
• 제41권7호
• /
• pp.21-29
• /
• 2004

본 논문에서는 Dual oxide를 갖는 Nano-scale CMOSFET에서 각 소자의 Hot carrier 특성을 분석하여 두 가지 중요한 결과를 나타내었다. 하나는 NMOSFET Thin/Thick인 경우 CHC stress 보다는 DAHC stress에 의한 소자 열화가 지배적이고, Hot electron이 중요하게 영향을 미치고 있는 반면에, PMOSFET에서는 특히 Hot hole에 의한 영향이 주로 나타나고 있다는 것이다. 다른 하나는, Thick MOSFET인 경우 여전히 NMOSFET의 수명이 PMOSFET의 수명에 비해 작지만, Thin MOSFET에서는 오히려 PMOSFET의 수명이 NMOSFET보다 작다는 것이다. 이러한 분석결과는 Charge pumping current 측정을 통해 간접적으로 확인하였다. 따라서 Nano-scale CMOSFET에서의 NMOSFET보다는 PMOSFET에 대한 Hot camel lifetime 감소에 관심을 기울여야 하며, Hot hole에 대한 연구가 진행되어야 한다고 할 수 있다.

• 한국전기전자재료학회논문지
• /
• 제16권9호
• /
• pp.771-774
• /
• 2003

In this paper, the programming characteristics of the multi-bit devices based on SONOS structure are investigated. Our devices have been fabricated by 0.35 $\mu\textrm{m}$ complementary metal-oxide-semiconductor (CMOS) process with LOCOS isolation. In order to achieve the multi-bit operation per cell, charges must be locally frapped in the nitride layer above the channel near the source-drain junction. Programming method is selected by Channel Hot Electron (CUE) injection which is available for localized trap in nitride film. To demonstrate CHE injection, substrate current (Isub) and one-shot programming curve are investigated. The multi-bit operation which stores two-bit per cell is investigated. Also, Hot Hole(HH) injection for fast erasing is used. The fabricated SONOS devices have ultra-thinner gate dielectrics and then have lower programming voltage, simpler process and better scalability compared to any other multi-bit storage Flash memory. Our programming characteristics are shown to be the most promising for the multi-bit flash memory.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.80-83
• /
• 2003

In this paper, the programming characteristics of the multi-bit devices based on SONOS structure are investigated. Our devices have been fabricated by $0.35\;{\mu}m$ complementary metal-oxide-semiconductor (CMOS) process with LOCOS isolation. In order to achieve the two-bits per cell operation, charges must be locally trapped in the nitride layer above the channel near the junction. Channel hot electron (CHE) injection for programming can operate in multi-bit using localized trap in nitride film. CHE injection in our devices is achieved with the single power supply of 5 V. To demonstrate CHE injection, substrate current (Isub) and one-shot programming curve were investigated. The multi-bit operation which stores two-bit per cell is investigated with a reverse read scheme. Also, hot hole injection for fast erasing is used. Due to the ultra-thin gate dielectrics, our results show many advantages which are simpler process, better scalability and lower programming voltage compared to any other two-bit storage flash memory. This fabricated structure and programming characteristics are shown to be the most promising for the multi-bit flash memory.

• 전자공학회논문지A
• /
• 제30A권12호
• /
• pp.77-87
• /
• 1993

PMOSFETs were studied on the effect of Hot-Carrier induced drain leakage current (Gate-Induced-Drain-Leakage). The result turned out that change in Vgl(drain voltage where 1pA/$\mu$m of drain leadage current flows) was largest in the Channel-Hot-Hole(CHH) injection condition and next was in dynamic stress and was smallest in electron trapping (Igmax) condition under various stress conditions. It was analyzed that if electron trapping occurrs in the overlap region of gate and drain(G/D), it reduces GIDL current due to increment of flat-band voltage(Vfb) and if CHH is injected, interface states(Nit) were generated and it increases GIDL current due to band-to-defect-tunneling(BTDT). Especially, under dynamic stress it was confirmed that increase in GIDL current will be high when electron injection was small and CHH injection was large. Therefore as applying to real circuit, low drain voltage GIDL(BTDT) was enhaced as large as CHH Region under various operating voltage, and it will affect the reliablity of the circuit.

• 대한전자공학회논문지
• /
• 제25권7호
• /
• pp.780-790
• /
• 1988

We have studied the hot-carrier-induced degradation caused by the high channel electric field due to the decrease of the gate length of MOSFET used in VLSI. Under DC stress, the condition in which maximum substrate current occures gave the worst degradation. Under AC dynamic stress, other conditions, the pulse shape and the falling rate, gave enormous effects on the degradation phenomena, especially at 77K. Threshold voltage, transconductance, channel conductance and gate current were measured and compared under various stress conditions. The threshold voltage was almost completely recovered by hot-injection stress as a reverse-stress. But, the transconductance was rapidly degraded under hot-hole injection and recovered by sequential hot-electron stress. The Si-SiO2 interface state density was analyzed by a charge pumping technique and the charge pumping current showed the same trend as the threshold voltage shift in degradation process.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권3호
• /
• pp.357-361
• /
• 1995

An experiment on characteristics of nMOSFET's in the long stress condition with the maximum of the substrate current has been carried out in order to study on the degradation due to the hot-carrier effect. Based on the measured result of the threshold voltage, the damage is mostly due to the hole injection into the oxide. After long stress, it was shown that the drain current increased at low gate voltages and hence decreased at high gate voltages.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 하계종합학술대회 논문집(2)
• /
• pp.327-330
• /
• 2004

It is shown that the hot carrier degradation due to enhanced hot holes trapping dominates PMOSFETs lifetime both in thin and thick devices. Moreover, it is found that in 0.13 ${\mu}m$ CMOSFET the PMOS lifetime under CHC (Channel Hot Carrier) stress is lower than the NMOSFET lifetime under DAHC (Drain Avalanche Hot Carrier) stress. Therefore. the interface trap generation due to enhanced hot hole injection will become a dominant degradation factor. In case of thick MOSFET, the degradation by hot carrier is confirmed using charge pumping current method and highly necessary to enhance overall device lifetime or circuit lifetime in upcoming nano-scale CMOS technology.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제8권1호
• /
• pp.11-20
• /
• 2008

The structure of 2-bit/cell flash memory device was characterized for sub-50 nm non-volatile memory (NVM) technology. The memory cell has spacer-type storage nodes on both sidewalls in a recessed channel region, and is erased (or programmed) by using band-to-band tunneling hot-hole injection (or channel hot-electron injection). It was shown that counter channel doping near the bottom of the recessed channel is very important and can improve the $V_{th}$ margin for 2-bit/cell operation by ${\sim}2.5$ times. By controlling doping profiles of the channel doping and the counter channel doping in the recessed channel region, we could obtain the $V_{th}$ margin more than ${\sim}1.5V$. For a bit-programmed cell, reasonable bit-erasing characteristics were shown with the bias and stress pulse time condition for 2-bit/cell operation. The length effect of the spacer-type storage node is also characterized. Device which has the charge storage length of 40 nm shown better ${\Delta}V_{th}$ and $V_{th}$ margin for 2-bit/cell than those of the device with the length of 84 nm at a fixed recess depth of 100 nm. It was shown that peak of trapped charge density was observed near ${\sim}10nm$ below the source/drain junction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.324-327
• /
• 2000

In this paper, the effects of negative and positive bias stress on p-channel poly-Si TFT's fabricated by excimer laser annealing have been investigated After positive and negative bias stress, transcon-ductance(g$_{m}$) is increased because of a reduction of the effective channel length due to the injected electron in the gate oxide. In the positive bias stress, the injection of hole is appeared after stress time of 3600sec and g$_{m}$ is decreased. On the other hand, the gate voltage at the maximum g$_{m}$, S-swing and threshold voltage(V$_{th}$) are decreased because of the interface state generation due to the injection of electrons into the gate oxide.e.ide.e.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.277-283
• /
• 1995

For the development of low NO$_{x}$ gas burners aimed for absorption chiller/heater unit, three proto type burners of different capacity (265000, 498000, and 664000 kcal/h) have been manufactured through a combustion method of step-by-step air injection. In order to characterize the overall features of the flame and the properties of the emission gas, the temperature of the flame and the concentration of NO$_{x}$ and CO were determined. The main factors in the design of burners (the area of primary air injection, the diameter of secondary air injection hole, fuel nozzle diameter) were observed to increase linearly with the scale-up of burner capacity. The flame temperature profiles of the burners were observed to be almost similar, irrespective of their capacity. However, as their capacity increased, the flame temperature slightly increased and the hot region of the flames moved to ward the flame tip along with the expansion to the direction of radius. From the proto type units, the amount of their NO$_{x}$ emission was determined to be around 25 - 30 vppm(3% )$_{2}$) and the CO emission was less than 19 vppm (3% $O_{2}$).TEX>).