• Carbon letters
• /
• v.16 no.2
• /
• pp.121-126
• /
• 2015

Carbon fibers are prepared by stabilizing pitch fibers accompanying electron beam (E-beam) irradiation. The carbon fibers pretreated by E-beam irradiation achieve a higher stabilization index than the carbon fibers that are only heat-stabilized. In addition, the carbon fibers subjected to E-beam irradiation in the stabilization step exhibit a comparable tensile strength to that of general purpose carbon fibers. The carbon fibers pretreated with an absorbed dose of 3000 kGy have a tensile strength of 0.54 GPa for a similar fiber diameter. Elemental, Fourier-transform infrared spectroscopy, and thermogravimetric analyses indicate that E-beam irradiation is an efficient oxidation and dehydrogenation treatment for pitch fibers by showing that the intensity of the aliphatic C-H stretching and aromatic $CH_2$ bending (out-of-plane) bands significantly decrease and carbonyl and carboxylic groups form.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.5
• /
• pp.1397-1400
• /
• 2013

The influence of electron beam irradiation on photocatalytic activity of $TiO_2$ thin films was investigated. $TiO_2$ thin films were prepared by anodization of Ti foil, and they were then subjected to an 1 MeV electron beam. Changes in physical properties and photocatalytic activity of $TiO_2$ before and after e-beam irradiation were investigated. The crystallinity of the synthesized materials was investigated by X-ray diffraction, and the oxidation states of both titanium and oxygen were determined by X-ray photoelectron spectroscopy (XPS). The density of donor ($N_d$) and flat band potential ($E_{fb}$) were investigated by Mott-Schottky analysis, and photocurrent was measured under a 1kW Xenon lamp illumination. After e-beam irradiation, significant change of Ti oxidation state was observed. $Ti^{3+}/Ti^{4+}$ ratio increased mainly due to the surface reduction by electron, and photocurrent was observed to increase with e-beam irradiation.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.4
• /
• pp.193-197
• /
• 2023

Transparent and conducting titanium (Ti) doped indium oxide (TIO) thin films were deposited on the poly-imide (PI) substrate with radio frequency magnetron sputtering and then electron irradiation was conducted on the TIO film's surface to investigate the effect electron irradiation on the crystallization and opto-electrical properties of the films. All x-ray diffraction (XRD) pattern showed two diffraction peaks of the In₂O₂ (431) and (444) planes with regardless of the electron beam irradiation energy. In the AFM analysis, the surface roughness of as deposited films was 3.29 nm, while the films electron irradiated at 700 eV, show a lower RMS roughness of 2.62 nm. In this study, the FOM of as deposited TIO films is 6.82 × 10^-3 Ω^-1, while the films electron irradiated at 500 eV show the higher FOM value of 1.0 × 10^-2 Ω^-1. Thus, it is concluded that the post-deposition electron beam irradiation at 500 eV is the one of effective methods of crystallization and enhancement of opto-electrical performance of TIO thin film deposited on the PI substrate.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.37-43
• /
• 2014

The crystallinity and molecular weight of cotton linter need to be controlled to be more easily dissolved in NMMO during manufacture of clothing fabrics. Electron beam irradiation and sulfuric acid treatment were used as pre-treatment to reduce molecular weight of cotton linter more efficiently, and after the pre-treatment, peroxide bleaching was followed in alkaline condition. After those processes, the crystalline indices of the cotton linters were measured by XRD method, and other properties such as their alpha cellulose contents and degree of polymerization were measured. It was found that the crystallinity index of cotton linter was decreased as the irradiation of electron beam increased while increased as the dose of sulfuric acid increased. These results strongly suggested that electron beam damaged the crystalline structure of the cellulose directly while sulfuric acid dissolved mostly non-crystalline area of the cellulose structure.

• Mass Spectrometry Letters
• /
• v.5 no.3
• /
• pp.89-93
• /
• 2014

Lincomycin is one of the major species among the Pharmaceuticals and Personal Care Products (PPCPs) detected from the four major rivers in Korea. The structure characterization was performed of six degradation products of lincomycin formed under the irradiation of electron beam, and the degradation efficiency as a function of the various irradiation dose and sample concentration was investigated. Electron beam (10 MeV, 0.5 mA and 5 kW) experiments for the structural characterization of degradation products that are fortified with lincomycin, were performed at the dose of 10 kGy. The separation of degradation products and lincomycin was carried out using a C18 column ($2.1{\times}100$ mm, $3.5{\mu}m$), using gradient elution with 20 mM ammonium acetate and acetonitrile. The structures of six degradation products of lincomycin were proposed by interpretation of mass spectra and chromatograms by LC-MS/MS. The mass fragmentation pathways of mass spectra in tandem mass spectrometry were also proposed. Experiments were performed of the degradation efficiency as a function of the irradiation dose intensity and the initial concentration of lincomycin in an aqueous environment. In addition, increased degradation efficiency was observed with a higher dose of electron beam and lower concentration.

• Journal of Radiation Industry
• /
• v.7 no.1
• /
• pp.23-28
• /
• 2013

In this study, we fabricated high density polyethylene (HDPE) composites filled with antioxidants and UV stabilizers. The electron beam irradiation on the fabricated composites was carried out over a range of absorbed doses from 50 to 200 kGy to confirm the changes of discoloration. The changes of discoloration were characterized using a color difference meter and FT-IR for confirming the changes of the color difference and structural change. It was observed that the color difference of IRGANOX 1010-, IRGAFOS 168-, and TINUVIN 328- added HDPE was higher than that of the control HDPE by electron beam irradiation. The melting temperature of UV stabilizer-added HDPE was not significantly changed by electron beam irradiation. However, the melting temperature of phenol-containing antioxidant-added HDPE was increased with increasing the absorbed dose. And the melting temperature of phosphorus-containing antioxidant-added composite was decreased with increasing the absorbed dose.

• Journal of Electrochemical Science and Technology
• /
• v.6 no.3
• /
• pp.75-80
• /
• 2015

We introduce a new synthesis method to prepare small TiO₂ nanoparticles with a narrow particle size distribution, which is achieved by electron beam (E-beam) irradiation. The effects of E-beam irradiation on the synthesis of TiO₂ nanoparticles and the electrochemical performance of TiO₂ nanoparticles as alternative anode materials for Li-ion batteries are investigated. The TiO₂ nanoparticles induced by E-beam irradiation present better cycling performance and rate capability than the TiO₂ nanoparticles synthesized by normal hydrolysis reaction. The better electrochemical performance is attributed to small particle size and narrow particle size distribution, resulting in the large surface area that provides innumerable reaction sites and short diffusion length for Li⁺ through TiO₂ nanoparticles.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.1
• /
• pp.29-33
• /
• 2010

Titanium nitride (TiN) films were deposited on the polycarbonate substrate by using radio frequency (RF) magnetron sputtering without intentional substrate heating. After deposition, the films were bombarded with intense electron beam for 20 minutes. The intense electron irradiation impacts on the crystalline, hardness and surface roughness of the TiN films. The films irradiated with an electron beam of 300 eV show the small grains on the surface, while as deposited TiN films did not showany grains on the surface. Also the surface harness evaluated with micro indenter was increased up to 18 Gpa at electron energy of 900 eV after electron beam irradiation. In addition, surface root mean square (RMS) roughness of the films irradiated with intense electron beam affected strongly. The films irradiated by electron beam with 900 eV have the lowest roughness of 1.2 nm in this study.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.6
• /
• pp.280-284
• /
• 2020

Electron beam irradiation is widely used as a type of surface modification technology to advance surface properties. In this study, the effect of electron beam irradiation on properties, such as surface hardness, wear resistance, roughness, and critical load of Titanium Aluminium nitride (TiAlN) films was investigated. TiAlN films were deposited on the SKD-61 substrate by using cathode arc ion plating. After deposition, the films were bombarded with intense electron beam for 10 minutes. The surface hardness was increased up to 4520 HV at electron irradiation energy of 1500 eV. In addition, surface root mean square (RMS) roughness of the films irradiated at 1500 eV shows the lowest roughness of 484 nm in this study.

• Nuclear Engineering and Technology
• /
• v.54 no.2
• /
• pp.486-492
• /
• 2022

Nitrogen oxides (NO_x; NO and NO₂) are major air pollutants and can cause harmful effects on the human body. Electron Beam Flue Gas Treatment (EBFGT) is a technology that generates electrons with an energy of 0.5-1 MeV using electron accelerators and effectively processes exhaust gases. In this study, NO_x was removed using an electron beam accelerator with spraying additives (NaOH and NH₄OH). NO and NO₂ were 100% and more than 94% removed, respectively, at an electron beam absorbed dose of 20 kGy and an additive concentration of 0.02 M (mol/L). In most cases, NO_x was removed better with lower initial NOx concentrations and higher electron beam absorbed doses. As the irradiation strength (mA) of the electron beam increases, the probability of electron impact on the material accordingly rises, which may lead to increase removal efficiency. The results of the present study show that the continuous electron beam process using additives achieved more effective removal efficiency than either individual process (wet-scrubbing or EB irradiation only).