• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.192-195
• /
• 2016

In this paper, we present a nanopower CMOS bandgap voltage reference working in sub-threshold region without resisters and bipolar junction transistors (BJT). Complimentary to absolute temperature (CTAT) voltage generator was realized by using two n-MOSFET pair with body bias circuit to make a sufficient amount of CTAT voltage. Proportional to absolute temperature (PTAT) voltage was generated from differential amplifier by using different aspect ratio of input MOSFET pair. The proposed circuits eliminate the use of resisters and BJTs for the operation in a sub-1V low supply voltage and for small die area. The circuits are implemented in 0.18um standard CMOS process. The simulation results show that the proposed sub-BGR generates a reference voltage of 290mV, obtaining temperature coefficient of 92 ppm/$^{\circ}C$ in -20 to $120^{\circ}C$ temperature range. The circuits consume 15.7nW at 0.63V supply.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.221-224
• /
• 2012

This paper presents a CMOS interface circuit for MEMS acceleration sensor. It consists of a capacitance to voltage converter(CVC), a second-order switched-capacitor (SC) integrator and comparator. A bandgap reference(BGR) has been designed to supply a stable bias to the circuit and a ${\Sigma}{\Delta}$ Modulator with chopper - stabilization(CHS) has also been designed for more suppression of the low frequency noise and offset. As a result, the output of this ${\Sigma}{\Delta}$ Modulator increases about 10% duty cycle when the input voltage amplitude increases 100mV and the sensitivity is x, y-axis 0.45v/g, z-axis 0.28V/g. This work is designed and implemented in a 0.35um CMOS technology with a supply voltage of 3.3V and a sampling frequency of 3MHz sampling frequency. The size of the designed chip including PADs is $0.96mm{\times}0.85mm$.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.3
• /
• pp.47-55
• /
• 1996

An optical transmitter, which is a key component of the optical transmission system, converts the electrical signal to optical signal and consists of a high-speed current-pulse driver for laser diode and low-speed feedback loops that stabilize optical power against aging, power supply voltage fluctuations, and ambient temperature changes. In this paper, the power-stabilizing part, which forms the bulk of the optical transmitter circuitry was designed in integrted circuits. Operational amplifiers and reference voltage generation circuits, which were identified as key building blocks for the power-stabilizing feedback loops, were designed and were subsequently verified through HSPICE simulations. The designed operational amplifier consists of a two-stage folded cascode amplifier and class AB output stage, whereas the reference voltage is obtained by bandgap reference circuits. Finally the power-stabilizing circuitry was laid out based on 3\mu$m CMOS design rules for fabrication.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.527-530
• /
• 2016

This paper presents curvature-compensated reference circuits operating under low-voltage condition and achieving low-power consumption with $0.35-{\mu}m$ standard CMOS process. The proposed circuit can operate under less than 1-V supply voltage by using MOS transistors operating in weak-inversion region. The simulation results shows a low temperature coefficient by using the proposed curvature compensation technique. It generates a graph-shape temperature characteristic that looks like a sine curve, not a bell-shape characteristic presented in other published BGRs without curvature compensation. The proposed circuits operate with 0.9-V supply voltage. First, the voltage reference circuit consumes 176nW power and the temperature coefficient is $26.4ppm/^{\circ}C$. The current reference circuit is designed to operate with 194.3nW power consumption and $13.3ppm/^{\circ}C$ temperature coefficient.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.838-841
• /
• 2012

To avoid the damage to circuit and performance degradation by temperature changes, temperature sensing circuit applicable to the IC is proposed in this paper. Temperature sensing is executed by PTAT circuit and power saving mode is activated by internal switch if internal temperature is in high. Also, characteristics of current matching are increased by using current mirror and cascode circuits. From the simulation results, this circuit is operating in action mode if input signal is in low. But it immediately goes into power saving mode if output signal is in high. It shows the output voltage of 1V at $75^{\circ}C$ and 1.75V at $125^{\circ}C$ in action mode and near 0 V(0V~ 7uV) in power saving mode.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.3
• /
• pp.105-108
• /
• 2003

In this work, a Voltage-to-Frequency Converter(VFC) in which the output frequency is proportional to the input voltage is proposed. To obtain the temperature stable characteristics of the VFC circuit is designed by BiCMOS technology. The output frequency range is 24KHz to 65KHz and the difference between simulated and calculated values is less than about 5% for this range of output frequency. The temperature variation of sample output frequencies is less than $\pm$0.5% in the temperature range $-25^{\circ}C$ to 75$^{\circ}C$.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.265-272
• /
• 2010

To supply a power distribution network with stable power in a high-speed mixed mode system, simultaneous switching noise caused at the multilayer PCB and package structures needs to be sufficiently suppressed. The uni-planar compact electromagnetic bandgap (UC-EBG) structure is well known as a promising solution to suppress the power noise and isolate noise-sensitive analog/RF circuits from a noisy digital circuit. However, a typical UC-EBG structure has several severe problems, such as a limitation in the stop band's lower cutoff frequency and signal quality degradation. To make up for the defects of a conventional EBG structure, a partially located EBG structure with decoupling capacitors is proposed in this paper as a means of both suppressing the power noise propagation and minimizing the effects of the perforated reference plane on the signal quality. The proposed structure is validated and investigated through simulation and measurement in both frequency and time domains.

• Journal of Sensor Science and Technology
• /
• v.25 no.5
• /
• pp.326-332
• /
• 2016

A novel CMOS temperature sensor with binary output is implemented by using fully differential switched-capacitor circuits for resistorless implementation of the temperature sensor core. Temperature sensing is based on the temperature characteristics of the pn diodes implemented by substrate pnp transistors fabricated using standard CMOS processes. The binary outputs are generated by using the charge-balance principle that eliminates the division operation of the PTAT voltage by the bandgap reference voltage. The chip was designed in a MagnaChip $0.35-{\mu}m$ CMOS process, and the designed circuit was verified using Spectre circuit simulations. The verified circuit was laid out in an area of $950{\mu}m{\times}557 {\mu}m$ and is currently under fabrication.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.6
• /
• pp.619-628
• /
• 2019

In this paper, we designed a beta ray sensor for a true random number generator. Instead of biasing the gate of the PMOS feedback transistor to a DC voltage, the current flowing through the PMOS feedback transistor is mirrored through a current bias circuit designed to be insensitive to PVT fluctuations, thereby minimizing fluctuations in the signal voltage of the CSA. In addition, by using the constant current supplied by the BGR (Bandgap Reference) circuit, the signal voltage is charged to the VCOM voltage level, thereby reducing the change in charge time to enable high-speed sensing. The beta ray sensor designed with 0.18㎛ CMOS process shows that the minimum signal voltage and maximum signal voltage of the CSA circuit which are resulted from corner simulation are 205mV and 303mV, respectively. and the minimum and maximum widths of the pulses generated by comparing the output signal through the pulse shaper with the threshold voltage (VTHR) voltage of the comparator, were 0.592㎲ and 1.247㎲, respectively. resulting in high-speed detection of 100kHz. Thus, it is designed to count up to 100 kilo pulses per second.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.6
• /
• pp.742-750
• /
• 2018

In this paper, in order to enable zero-layer FTP cell using only 5V MOS devices on the basis of $0.13{\mu}m$ BCD process, the tunnel oxide thickness is used as the gate oxide thickness of $125{\AA}$ of the 5V MOS device at 82A. The HDNW layer, which is the default in the BCD process, is used. Thus, the proposed zero layer FTP cell does not require the addition of tunnel oxide and DNW mask. Also, from the viewpoint of memory IP design, a single memory structure which is used only for trimming analog circuit of PMIC chip is used instead of the dual memory structure dividing into designer memory area and user memory area. The start-up circuit of the BGR (Bandgap Reference Voltage) generator circuit is designed to operate in the voltage range of 1.8V to 5.5V. On the other hand, when the 64-bit FTP memory IP is powered on, the internal read signal is designed to maintain the initial read data at 00H. The layout size of the 64-bit FTP IP designed using the $0.13-{\mu}m$ Magnachip process .is $485.21{\mu}m{\times}440.665{\mu}m$($=0.214mm^2$).