• Journal of Korean Vacuum Science & Technology
• /
• 제4권1호
• /
• pp.6-10
• /
• 2000

Ferroelectric YMnO$_3$ thin films were deposited on $Y_2$O$_3$/si(100) substrates by metalorganic chemical vapor deposition. The YMnO$_3$ thin films annealed in vacuum ambient (100 mTorr) above 75$0^{\circ}C$ show hexagonal structured YMnO$_3$. However, the film annealed in oxygen ambient shows poor crystallinity, and the second phase as $Y_2$O$_3$ and orthorhombic-YMnO$_3$ were shown. The annealing ambient and pressure on the crystallinity of YMnO$_3$ thin films is very important. The C-V characteristics have a hysteresis curve with a clockwise rotation, which indicates ferroelectric polarization switching behavior. When the gate voltage sweeps from +5 to 5 V, the memory window of the Pt/YMnO$_3$/Y$_2$O$_3$/Si gate capacitor annealed at 85$0^{\circ}C$ is 1.8 V. The typical leakage current densities of the films annealed in oxygen and vacuum ambient are about 10$^{-3}$ and 10$^{-7}$ A/cm$^2$ at applied voltage of 5 V.

• 한국재료학회지
• /
• 제18권9호
• /
• pp.486-491
• /
• 2008

The effect of annealing treatment conditions on the interfacial adhesion energy between electrolessplated Ni film and polyimide substrate was evaluated using a $180^{\circ}$ peel test. Measured peel strength values are $26.9{\pm}0.8,\;22.4{\pm}0.8,\;21.9{\pm}1.5,\;23.1{\pm}1.3,\;16.1{\pm}2.0\;and\;14.3{\pm}1.3g/mm$ for annealing treatment times during 0, 1, 3, 5, 10, and 20 hours, respectively, at $200^{\circ}C$ in ambient environment. XPS and AES analysis results on peeled surfaces clearly reveal that the peeling occurs cohesively inside polyimide. This implies a degradation of polyimide structure due to oxygen diffusion through interface between Ni and polyimide, which is also closely related to the decrease in the interfacial adhesion energy due to thermal treatment in ambient conditions.

• 한국전기전자재료학회논문지
• /
• 제24권5호
• /
• pp.370-373
• /
• 2011

We investigated the effects of low temperature ($500^{\circ}C$) $O_2$ annealing on the characteristics of hafnium silicate ($HfSi_xO_y$) films deposited on a Si substrate by atomic layer deposition (ALD). We found that the post deposition annealing under oxidizing ambient causes the oxidation of residual Hf metal components, resulting in the improvement of electrical characteristics such as flat band voltage shift (${\Delta}V_{fb}$) by hysteresis without oxide capacitance reduction. We suggest that post deposition annealing under oxidizing ambient is necessary to improve the electrical characteristics of $HfSi_xO_y$ films deposited by ALD.

• 한국통신학회논문지
• /
• 제35권11A호
• /
• pp.1091-1096
• /
• 2010

Stiction in microelectromechanical systems (MEMS) has been a major failure mechanism. Especially, in RF MEMS switches, moving parts often suffered in-use and release related stiction problems. Some materials and methods have been used to prevent this problem. Diamond-like carbon (DLC) has not only been used as a protective material owing to its good mechanical properties but also has been used as a hydrophobic material. Its properties could be controlled by post annealing treatment in various conditions. We synthesized DLC films using a radio frequency plasma enhanced chemical vapor deposition (RF PECVD) method on silicon substrates using methane ($CH_4$) and hydrogen ($H_2$) gas. Then, the change of the hydrophobic property of the films was investigated undervarious annealing temperatures in nitrogen and in oxygen ambient. The films, that were annealed above $700^{\circ}C$ in nitrogen ambient, showed a high contact angle of water (> $90^{\circ}$) even though their mechanical property was sacrificed to some degree. The structural variation and the changes of the hydrophobic and mechanical properties of the DLC films were analyzed by Raman spectrum, contact angle measurement, surface profiler, and a nanoindentation test.

• Transactions on Electrical and Electronic Materials
• /
• 제16권2호
• /
• pp.62-64
• /
• 2015

We have investigated zinc tin oxide (ZTO) thin films under various silicon ratios. ZTO TFTs were fabricated by solution processing with the bottom gate structure. Furthermore, annealing process was performed at different temperatures in various annealing conditions, such as air, vacuum and wet ambient. Completed fabrication of ZTO TFT, and the performance of TFT has been compared depending on the annealing conditions by measuring the transfer curve. In addition, structure in ZTO thin films has been investigated by X-ray diffraction spectroscopy (XRD) and Scanning electron microscope (SEM). It is confirmed that the electrical performance of ZTO TFTs are improved by adopting optimized annealing conditions. Optimized annealing condition has been found for obtaining high mobility.

• 한국전기전자재료학회논문지
• /
• 제25권7호
• /
• pp.543-551
• /
• 2012

In this study, transparent conducting Al-doped Zinc Oxide (AZO) films with a thickness of 150 nm were prepared on corning glass substrate by the RF magnetron sputtering with using a Al-doped zinc oxide (AZO), ($Al_2O_3$: 2 wt%) target at room temperature. This study investigated the effect of rapid thermal annealing temperature and oxygen ambient on structural, electrical and optical properties of Al-doped zinc oxide (AZO) thin films. The films were annealed at temperatures ranging from 400 to $700^{\circ}C$ by using Rapid thermal equipment in oxygen ambient. The effect of RTA treatment on the structural properties were studied by x-ray diffraction and atomic force microscopy. It is observed that the Al-doped zinc oxide (AZO) thin film annealed at $500^{\circ}C$ at 5 minute oxygen ambient gas reveals the strongest XRD emission intensity and narrowest full width at half maximum among the temperature studied. The enhanced UV emission from the film annealed at $500^{\circ}C$ at 5 minute oxygen ambient gas is attributed to the improved crystalline quality of Al-doped zinc oxide (AZO) thin film due to the effective relaxation of residual compressive stress and achieving maximum grain size.

• Journal of information and communication convergence engineering
• /
• 제2권3호
• /
• pp.149-152
• /
• 2004

In this paper, we present the film bulk acoustic resonator (FBAR) devices fabricated by considering the effects of annealing temperature on zinc oxide (ZnO) film growth characteristics. In order to determine the annealing temperature and annealing time at which the ZnO film can have good material properties, the several resonators containing ZnO layers were fabricated and annealed at various temperatures from $27^{\circ}C\;to\;300^{\circ}C$ in Ar gas ambient. The effects of the annealing temperature and annealing time on the ZnO film properties were comprehensively studied in order to further improve the resonance characteristics of FBAR resonators.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2004년도 SMICS 2004 International Symposium on Maritime and Communication Sciences
• /
• pp.16-19
• /
• 2004

In this paper, we present the film bulk acoustic resonator (FBAR) devices fabricated by considering the effects of annealing temperature on zinc oxide (ZnO) film growth characteristics. In order to determine the annealing temperature and annealing time at which the ZnO film can have good material properties, the several resonators containing ZnO layers were fabricated and annealed at various temperatures from 27$^{\circ}C$ to 30$0^{\circ}C$ in Ar gas ambient. The effects of the annealing temperature and annealing time on the ZnO film properties were comprehensively studied in order to further improve the resonance characteristics of FBAR resonators.

• Transactions on Electrical and Electronic Materials
• /
• 제16권1호
• /
• pp.34-36
• /
• 2015

Amorphous SiZnSnO(SZTO) thin film transistors(TFTs) have been fabricated by RF magnetron sputtering process, and they were annealed in air and in wet ambient. The electrical performance and the structure were analyzed by I-V measurement, XPS, AFM, and XRD. The results showed improvement in device performance by wet annealing process compared to air annealing treatment, because free electron was shown to be increased due to reaction of oxygen and hydrogen generating oxygen vacancy. This is understood by the generation of free electrons. We expect the wet annealing process to be a promising candidate to contributing to high electrical performance of oxide thin film transistors for backplane device applications.

• 한국표면공학회지
• /
• 제24권4호
• /
• pp.196-205
• /
• 1991

Multi-level thin films are very important in ULSI applications because of their high electromigration resistance. This study presents the effects of titanium, titanium nitride and titanium tungsten underlayers of the stability of multi-aluminum thin films during isothermal annealing. High purity Al(99.999%) films have been electron-beam evaporated on Ti, TiN, TiW films formed on SiO2/Si (P-type(100))-wafer substrates by RF-sputtering in Ar gas ambient. The hillock growth was increased with annealing temperatures. Growth of hillocks was observed during isothermal annealing of the thin films by scanning electron microscopy. The hillock growth was believed to appear due to the recrystallization process driven by stress relaxation during isothermal annealing. Thermomigration damage was also presented in thin films by grain boundary grooving processes. It is shown that underlayers of Al/TiN/SiO2, Al/TiW/SiO2 thin films are preferrable to Al/SiO2 thin film metallization.