• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.81-85
• /
• 2013

Wafer stacking technology becomes more important for the next generation IC technology. It requires new process development such as TSV, wafer bonding, and wafer thinning and also needs to resolve wafer warpage, power delivery, and thermo-mechanical reliability for high volume manufacturing. In this study, Cu CMP which is the key process for wafer bonding has been studied using Cu CMP and oxide CMP processes. Wafer samples were fabricated on 8" Si wafer using a damascene process. Cu dishing after Cu CMP and oxide CMP was $180{\AA}$ in average and the total height from wafer surface to bump surface was approximately $2000{\AA}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.12 no.1
• /
• pp.27-34
• /
• 1999

We investigated the effect of mechanical back side damage in viewpoint of electrical and surface morphological characteristics in Czochralski silicon wafer. The intensity of mechanical damage was evaluated by minority carrier recombination lifetime by laser excitation/microwave reflection photoconductance decay technique, atomic force microscope, optical microscope, wet oxidation/preferential etching methods. The data indicate that the higher the mechanical damage degree, the lower the minority carrier lifetime, and surface roughness, damage depth and density of oxidation induced stacking fault increased proportionally.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.3
• /
• pp.71-74
• /
• 2013

In this study, the effects of wafer warpage on the misalignment during wafer stacking process were investigated. The wafer with $45{\mu}m$ bow height warpage was purposely fabricated by depositing Cu thin film on a silicon wafer and the bonding misalignment after bonding was observed to range from $6{\mu}m$ to $15{\mu}m$. This misalignment could be explained by a combination of $5{\mu}m$ radial expansion and $10{\mu}m$ linear slip. The wafer warpage seemed to be responsible for the slip-induced misalignment instead of radial expansion misalignment.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.05a
• /
• pp.15.1-15.1
• /
• 2007

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.535-542
• /
• 1998

SOI(silicon oninsulator) was fabricated through the direct bonding of a hydrophilized single crystal Si wafer and a thermally oxidized SiO2 thin film to investigate the stacking faults in silicon at the Si/SiO2 in-terface. At first the oxidation kinetics of SiO2 thin film and the stacking fault distribution at the oxidation interface were investigated. The stacking faults could be divided into two groups by their size and the small-er ones were incorporated into the larger ones as the oxidation time and temperature increased. The den-sity of the smaller ones based critically lower eventually. The SOI wafers directly bonded at the room temperature were annealed at 120$0^{\circ}C$ for 1 hour. The stacking faults at the bonding and oxidation interface were examined and there were anomalies in the distributions of the stacking faults of the bonded region to arrange in ordered ring-like fashion.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1510-1512
• /
• 2000

Due to the shrinking of the chip size and increasing of the complexity in the modern electronic devices. the defect of wafer are so important to decide the yield in the device process. The engineers has studied the wafer defects and the characteristics. They published lots of the experimental methods. I did an experiment the gettering effect of the defects due to the high temperature and the long time diffusion. Actually, As the thickness of the wafer backside polysilicon is thicker and the diffusion time is faster. the defects on the wafer are decreased. The polysilicon gram boundaries of the wafer backside played an important part as the defect gettering site.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.229-231
• /
• 2007

Recently, 3D-electronic packaging by TSV is in interest. TSV(Through Silicon Via) is a interconnection hole on Si-wafer filled with conducting metal such as Copper. In this research, chips with TSV are connected by electroplated Sn bump without PR. Then chips with TSV are put together and stacked by the methode of Reflow soldering. The stacking was successfully done and had no noticeable defects. By eliminating PR process, entire process can be reduced and makes it easier to apply on commercial production.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.3
• /
• pp.116-120
• /
• 2017

Temperature uniformity of a wafer in a semiconductor process is a very important factor that determines the overall yield. Therefore, it is very important to confirm the temperature characteristics of the chuck surface on which the wafer is lifted. The temperature characteristics of the chuck depend on the external heat source, the shape of the cooling channel inside the chuck, the material on the chuck surface, and so on. In this study, CFD confirms the change of temperature characteristics according to the stacking order of ceramic materials on the chuck surface, and suggests the best lamination method.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.127.1-127.1
• /
• 2000

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.1
• /
• pp.1-5
• /
• 2013

Wafer-to-Wafer (W2W) integration technology is an emerging technology promising many benefits, such as reduced size, improved performance, reduced power, lower cost, and divergent integration. As the maturity of W2W technology progresses, new applications will become more viable. However, at present the cost for W2W integration is still very high and both manufacturing yield and reliability issues have not been resolved yet for high volume manufacturing (HVM). Especially for WTW integration resolving compound yield issue can be a key factor for HVM. To have the full benefits of WTW integration technology more than simple wafer stacking technologies are necessary. In this paper, the manufacturing yield for W2W integration is described and the challenges of WTW integration will be discussed.