• Korean Journal of Materials Research
• /
• v.16 no.5
• /
• pp.308-311
• /
• 2006

The purpose of this study is to investigate the difference of the wafer nanotopography impact on the oxide-film thickness variation between the STI CMP using ceria slurry and STI CMP using fumed silica slurry. The nanotopography impact on the oxide-film thickness variation after STI CMP using ceria slurry is 2.8 times higher than that after STI CMP using fumed silica slurry. It is attributed that the STI CMP using ceria slurry follows non-Prestonian polishing behavior while that using fumed silica slurry follows Prestonian polishing behavior.

• Journal of the Korea Society for Simulation
• /
• v.23 no.3
• /
• pp.27-32
• /
• 2014

In this paper, We are going to propose the novel structure with improved behavior than the conventional vertical structure for VLSI CMOS circuits. For this, the proposed structure is the moat shape for STI. We want to analysis the characteristics of simulations about the electron concentration distribution, oxide layer shape of hot electron stress, potential flux and electric field flux, electric field fo themal damage and current-voltage characteristics in devices. Physically based models are the ambient and stress bias conditions of TCAD tool. As a analysis results, shallow trench structure were trended to be electric functions of passive as device dimensions shrink. The electrical characteristics influence of proposed STI structures on the transistor applications become stronger the potential difference electric field and saturation threshold voltage, are decreased the stress effects of active region. The fabricated device of based on analysis results data were the almost same characteristics of simulation results data.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2509-2515
• /
• 2014

In this paper, the conventional vertical structure for VLSI circuits CMOS intend to improve the stress effects of active region and built-in threshold voltage. For these improvement, the proposed structure is shallow trench isolation of moat shape. We want to analysis the electron concentration distribution, gate bias vs energy band, thermal stress and dielectric enhanced field of thermal damage between vertical structure and proposed moat shape. Physically based models are the ambient and stress bias conditions of TCAD tool. As an analysis results, shallow trench structure were intended to be electric functions of passive as device dimensions shrink, the electrical characteristics influence of proposed STI structures on the transistor applications become stronger the potential difference electric field and saturation threshold voltage, are decreased the stress effects of active region. The fabricated device of based on analysis results data were the almost same characteristics of simulation results data.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.5
• /
• pp.1-7
• /
• 2002

Deep sub-micron bulk CMOS circuits require gate electrode materials such as metal silicide and titanium silicide for gate oxides. Many authors have conducted research to improve the quality of the sub-micron gate oxide. However, few have reported on the electrical quality and reliability of an ultra-thin gate. In this paper, we will recommend a novel shallow trench isolation structure and a two-step TiS $i_2$ formation process to improve the corner metal oxide semiconductor field-effect transistor (MOSFET) for sub-0.1${\mu}{\textrm}{m}$ VLSI devices. Differently from using normal LOCOS technology, deep sub-micron CMOS devices using the novel shallow trench isolation (STI) technology have unique "inverse narrow-channel effects" when the channel width of the device is scaled down. The titanium silicide process has problems because fluorine contamination caused by the gate sidewall etching inhibits the silicide reaction and accelerates agglomeration. To resolve these Problems, we developed a novel two-step deposited silicide process. The key point of this process is the deposition and subsequent removal of titanium before the titanium silicide process. It was found by using focused ion beam transmission electron microscopy that the STI structure improved the narrow channel effect and reduced the junction leakage current and threshold voltage at the edge of the channel. In terms of transistor characteristics, we also obtained a low gate voltage variation and a low trap density, saturation current, some more to be large transconductance at the channel for sub-0.1${\mu}{\textrm}{m}$ VLSI devices.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.2
• /
• pp.102-106
• /
• 2005

A low dark current CMOS image sensor (CIS) pixel without any process modification is developed. Dark current is mainly generated at the interface region of shallow trench isolation (STI) structure. Proposed pixel reduces the dark current effectively by separating the STI region from the photodiode junction using simple layout modification. Test sensor array that has both proposed and conventional pixels is fabricated using 0.18 m CMOS process and the characteristics of the sensor are measured. The result shows that the dark current of the proposed pixel is 0.93fA/pixel that is two times lower than the conventional design.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.33-36
• /
• 2001

Chemical mechanical polishing(CMP) process has been widely used to planarize dielectric layers, which can be applied to the integrated circuits for deep sub-micron technology. The rise throughput and the stability in the device fabrication can be obtained by applying of CMP process to STI structure in 0.18$\mu\textrm{m}$ m semiconductor device. The reverse moat process has been added to employ in of each thin films in STI-CMP was not equal, hence the devices must to be effected, that is, the damage was occurred in the device area for the case of excessive CMP process and the nitride film was remained on the device area for the case of insufficient CMP process, and than, these defects affect the device characteristics. Also, we studied the High Selectivity Slurry(HSS) to perform global planarization without reverse moat step.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.64-64
• /
• 2003

고집적화된 시스템 LSI 반도체 소자 제조 공정에서 소자의 고속화 및 고성능화에 따른 배선층수의 증가와 배선 패턴 미세화에 대한 요구가 갈수록 높아져, 광역평탄화가 가능한 STI CMP(Shallow Trench Isolation Chemical-Mechanical-Polishing)공정의 중요성이 더해가고 있다. 이러한 STI CMP 공정에서 세리아 슬러리에 첨가되는 계면활성제의 농도에 따라 산화막과 질화막 사이의 연마 선택비를 제어하는 것이 필수적 과제로 등장하고 있다. 일반적인 CMP 공정에서 압력 증가에 따른 연마 제거량이 Prestonian 거동을 나타내는 반면, 연마 입자의 크기를 변화시켜 계면활성제의 농도를 달리 하였을 경우, 압력 변화에 따라 Non-Prestonian 거동이 나타나는 것을 고찰할 수 있었다. 따라서 본 연구에서는 세리아 슬러리 내에 첨가되는 계면활성 제의 농도와 연마입자의 크기를 달리한 후, 압력을 변화시킴으로 나타나는 non-Prestonian 거동에 미치는 영향에 대하여 연구하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.54-57
• /
• 2001

We studied the characteristics of polishing pad, which can apply STI-CMP process for global planarization of multilevel interconnection structure. Also, we investigated the effects of different sets of polishing pad, such as soft and hard pad. As an experimental result, hard pad showed center-fast type, and soft pad showed edge-fast type. Totally, the defect level has shown little difference, however, the counts of scratch was defected less than 2 on JRlll pad. Through the above results, we can select optimum polishing pad, so we can expect the improvements of throughput and devise yield.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.1
• /
• pp.15-20
• /
• 2004

Through shallow trench isolation (STI) chemical mechanical polishing (CMP) tests, we investigated the dependence of pad surface temperature on the abrasive and additive concentrations in ceria slurry under varying pressure using blanket film wafers. The pad surface temperature after CMP increased with the abrasive concentration and decreased with the additive concentration in slurries for the constant down pressure. A possible mechanism is that the additive adsorbed on the film surfaces during polishing decreases the friction coefficient, hence the pad surface temperature gets lower with increasing the additive concentration. This difference in temperature was more remarkable for the higher concentration of abrasives. In addition, in-situ measurement of spindle motor was carried out during oxide and nitride polishing. The averaged motor current for oxide film was higher than that for nitride film, meaning the higher friction coefficient.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.211-213
• /
• 1999

In this paper, we documented the controlling oxide removal amount on the pattern wafer using removal rate and removal thickness of blanket wafer. There was the strong correlation relationship for both(correlation factor:0.7109). So, we could confirm the repeatability as applying for STI CMP process from the obtained linear formular. As the result of repeatability test, the difference of calculated polishing time and actual polishing time was 3.48 seconds based on total 50 lots. If this time is converted into the thickness, it is from 104$\AA$ to 167$\AA$. It is possible to be ignored because it is under the process margin.