• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.591-592
• /
• 2006

Schottky diodes for Radio-frequency identification (RFID) tag integration on chip were designed and fabricated using Samsung electronics System LSI standard $0.18{\mu}m$ CMOS process. Schottky diodes were designed as interdigitated fingers array by CMOS layout design rule. 64 types of Schottky diode were designed and fabricated with the variation of finger width, length and numbers with a $0.6{\mu}m$ guard ring enclosing n-well. Titanium was used as Schottky contact metal to lower the Schottky barrier height. Barrier height of the fabricated Schottky diode was 0.57eV. DC current - voltage measurements showed that the fabricated Schottky diode had a good rectifying properties with a breakdown voltage of -9.15 V and a threshold voltage of 0.25 V.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.834-838
• /
• 2002

In this paper, we have fabricated 4H-SiC schottky diodes utilizing a metal-oxide overlap structure for electric filed termination. The barrier height and Ideality factor were measured by current-voltage, capacitance-voltage characteristics. Schottky barrier height(SBH) were 1.41ev for Ni and 1.35eV for Pt, 1.52eV for Pt/Ti at room temperature and Pt/Ti Schottky diode exhibited Ideality factor was 1.06 to 1.4 in the range of $25^{\circ}C{\sim}200^{\circ}C$. To improve the reverse bias characteristics, an edge termination technique is employed for Pt/Ti/4H-SiC Schottky rectifiers and the device show excellent characteristics with higher blocking voltage up to 780V compared with unterminated devices.

• 한국전기전자재료학회논문지
• /
• 제24권4호
• /
• pp.266-270
• /
• 2011

We report on the formation mechanism of large Schottky barrier height (SBH) of nonalloyed Cr Schottky contacts on strained Al0.25Ga0.75N/GaN. Based on the current-voltage (I-V) and capacitance-voltage (C-V) data, the SBHs are determined to be 1.98 (${\pm}0.02$) and 2.07 (${\pm}0.02$) eV from the thermionic field emission and two-dimensional electron gas (2DEG) calculations, respectively. Possible formation mechanism of large SBH will be described in terms of the formation of Cr-O chemical bonding at the interface between Cr and AlGaN/GaN, low binding-energy shift to surface Fermi level, and the reduction of 2DEG electrons.

• 전기전자학회논문지
• /
• 제26권2호
• /
• pp.306-312
• /
• 2022

서로 다른 PN 비율과 금속화 어닐링 온도에 의해 장벽 높이가 다른 4H-SiC 병합 PiN Schottky(MPS) 다이오드의 전기적 특성과 심층 트랩을 조사했다. MPS 다이오드의 장벽 높이는 IV 및 CV 특성에서 얻었다. 전위장벽 높이가 낮아짐에 따라 누설 전류가 증가하여 10배의 전류가 발생하였다. 또한, 심층 트랩(Z_1/2 및 RD_1/2)은 4개의 MPS 다이오드에서 DLTS 측정을 통해 밝혀졌다. DLTS 결과를 기반으로, 트랩 에너지 준위는 낮은 장벽 높이와 함께 22~28%의 얕은 수준으로 확인되었다. 이는 쇼트키 장벽 높이에 대해 DLTS에 의해 결정된 결함 수준 및 농도의 의존성을 확인할 수 있다.

• Transactions on Electrical and Electronic Materials
• /
• 제16권3호
• /
• pp.151-155
• /
• 2015

We fabricated the Cu Schottky contact on an n-type Ge wafer and investigated the forward bias current-voltage (I-V) characteristics in the temperature range of 100~300 K. The zero bias barrier height and ideality factor were determined based on the thermionic emission (TE) model. The barrier height increased and the ideality factor decreased with increasing temperature. Such temperature dependence of the barrier height and the ideality factor was associated with spatially inhomogeneous Schottky barriers. A notable deviation from the theoretical Richardson constant (140.0 Acm^-2K^-2 for n-Ge) on the conventional Richardson plot was alleviated by using the modified Richardson plot, which yielded the Richardson constant of 392.5 Acm^-2K^-2. Finally, we applied the theory of space-charge-limitedcurrent (SCLC) transport to the high forward bias region to find the density of localized defect states (N_t), which was determined to be 1.46 × 10¹² eV^-1cm^-3.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.56-63
• /
• 1995

MESFETs of the Ti/Au and Ti/Pd/Au gate were fabricated on n-type GaAs. Interdiffusion at Schottky interfaces, Schottky contact properties, and MESFET characteristics with heat treatment were investigated. Ti of Ti/Au contact and Pd of Ti/Pd/Au contact acted as a barrier metal against interdiffusion of Au at >$220^{\circ}C$. Pd of Ti/Pd/Au contact acted as a barrier metal even at >$360^{\circ}C$, however, Ti of Ti/Au contact promoted interdiffusion of Au instead of role of barrier metal. As the heat treatment temperature increases, in the case of both contact, saturated drain current and pinch off voltage decreased, open channel resistance increased, and degree of parameter variation in Ti/Au gate was higher than in Ti/Pd/Au gate at >$360^{\circ}C$ Schottky barrier height of Ti/Au and Ti/Pd/Au contacts was 0.69eV and 0.68eV in the as-deposited state, respectively, and Fermi level was pinned in the vicinity of 1/2Eg. As the heat treatment temperature increases, barrier height of Ti/Pd/Au contact increased, however, decreased at >$360^{\circ}C$ in the case of Ti/Au contact. Ideality factor of Ti/Au contact was nearly constant regardless of heat treatment, however, increased at >$360^{\circ}C$ in the case of Ti/Au contact. From the results above, Ti/Pd/Au was stable gate metal than Ti/Au.

• 한국전기전자재료학회논문지
• /
• 제14권7호
• /
• pp.533-538
• /
• 2001

The barrier height is found to increase from 0.25 to 0.690 eV for Schottky contacts on n-InGaAs using deposition of Ag on a substrate cooled to 77K(LT). Surface analysis leads to an interface model for the LT diode in which there are oxide compounds of In:O and As:O between the metal and semiconductor, leading to behavior as a metal-insulator-semiconductor diode. The metal film deposited t LT has a finer and more uniform structure, as revealed by scanning electron microscopy and in situ metal layer resistance measurement. This increased uniformity is an additional reason for the barrier height improvement. In contrast, the diodes formed at room temperature exhibit poorer performance due to an unpassivated surface and non-uniform metal coverage on a microscopic level.

• 한국전기전자재료학회논문지
• /
• 제31권6호
• /
• pp.367-371
• /
• 2018

1,200 V class junction barrier schottky (JBS) diodes and schottky barrier diodes (SBD) were simultaneously fabricated on the same 4H-SiC wafer. The resulting diodes were characterized at temperatures from room temperature to 473 K and subsequently compared in terms of their respective I-V characteristics. The parameters deduced from the observed I-V measurements, including ideality factor and series resistance, indicate that, as the temperature increases, the threshold voltage decreases whereas the ideality factor and barrier height increase. As JBS diodes have both Schottky and PN junction structures, the proper depletion layer thickness, $R_{on}$, and electron mobility values must be determined in order to produce diodes with an effective barrier height. The comparison results showed that the JBS diodes exhibit a larger effective barrier height compared to the SBDs.

• 반도체디스플레이기술학회지
• /
• 제14권1호
• /
• pp.27-30
• /
• 2015

SiC based Schottky barrier diodes were prepared by using the facing targets sputtering method. In this research, 4H-SiC polytypes of SiC were adopted and Molybdenum, Titanium was employed as the Schottky metal of the metal-semiconductor contacts. Both structures showed the rectifying nature in their forward and reverse J-V characteristic curve and the ideality factors calculated from these plots that were close to unity were represented the nearly ideal behavior. Difference of Schottky barrier height between prepared devices was also corresponding with the electrical characteristics of themselves. Therefore the suitability of the facing targets sputtering method for fabrication of Schottky diodes could be suggested from these results.

• 한국전기전자재료학회논문지
• /
• 제24권4호
• /
• pp.261-265
• /
• 2011

This paper describes the fabrication and characteristics of a Au/Ni/Ti/3C-SiC Schottky diode with field plate (FP) edge termination. The Schottky contacts were annealed for 30 min at temperatures ranging from 0 to $800^{\circ}C$. At annealing temperature of $600^{\circ}C$, it showed an inhomogeneous Schottky barrier and had the best electrical characteristics. However, the annealing of $800^{\circ}C$ replaced it with ohmic behaviors because of the formation of many different types of nickel silicides. The fabricated Schottky diode had a breakdown voltage of 200 V, Schottky barrier height of 1.19 eV and worked normally even at $200^{\circ}C$.