• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.443-451
• /
• 2010

This paper describes a fully integrated CMOS low-IF mobile-TV RF tuner for Band-III T-DMB/DAB applications. All functional blocks such as low noise amplifier, mixers, variable gain amplifiers, channel filter, phase locked loop, voltage controlled oscillator and PLL loop filter are integrated. The gain of LNA can be controlled from -10 dB to +15 dB with 4-step resolutions. This provides a high signal-to-noise ratio and high linearity performance at a certain power level of RF input because LNA has a small gain variance. For further improving the linearity and noise performance we have proposed the RF VGA exploiting Schmoock's technique and the mixer with current bleeding, which injects directly the charges to the transconductance stage. The chip is fabricated in a 0.18 um mixed signal CMOS process. The measured gain range of the receiver is -25~+88 dB, the overall noise figure(NF) is 4.02~5.13 dB over the whole T-DMB band of 174~240 MHz, and the measured IIP3 is +2.3 dBm at low gain mode. The tuner rejects the image signal over maximum 63.4 dB. The power consumption is 54 mW at 1.8 V supply voltage. The chip area is $3.0{\times}2.5mm^2$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1199-1202
• /
• 2008

High mobility bottom gate thin film transistors (TFTs) with an amorphous gallium tin zinc oxide (a-GSZO) channel layer have been produced by rf magnetron cosputtering using a gallium zinc oxide (GZO) and tin (Sn) targets. The effect of the post annealing temperatures ($200^{\circ}C$, $250^{\circ}C$ and $300^{\circ}C$) was evaluated and compared with two series of TFTs produced at room temperature and $150^{\circ}C$ during the channel deposition. From the results it was observed that the effect of pos annealing is crucial for both series of TFTs either for stability as well as for improving the electrical characteristics. The a-GSZO TFTs operate in the enhancement mode (n-type), present a high saturation mobility of $24.6\;cm^2/Vs$, a subthreshold gate swing voltage of 0.38 V/decade, a turn-on voltage of -0.5 V, a threshold voltage of 4.6 V and an $I_{ON}/I_{OFF}$ ratio of $8{\times}10^7$, satisfying all the requirements to be used in active-matrix backplane.

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.36-43
• /
• 1997

FECAPS(ferroelectric capacitors) have been fabricated by RF magnetron sputtering deposition of 3000$\AA$ PZT thin films on the Pt/Ti/$SiO_2$/Si substrates and post-annealing with the temperature of $550^{\circ}C$~$650^{\circ}C$ for 10 sec~50 sec in a RTA system. The electrical characteristics of the fabricated capacitors showed the highest dielectric constant and remanent polarization[${\varepsilon_r(1kHz)$=690, $2P_r$(-5V~5V sweep)=22$\mu$C/$ \textrm{cm}^2$] in the samples annealed at $650^{\circ}C$ for 30 sec, while the lowest tangent loss and leakage current [$tan\delta(\ge10kHz)\le0.02, \; J_i(5V)=3\mu\textrm{A}/\textrm{cm}^2$]in the samples annealed at $600^{\circ}C$ for 30 sec.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.183-184
• /
• 2013

Two main MBE growth techniques have been used: plasma-assisted MBE (PA-MBE), which utilizes a rf plasma to supply active nitrogen, and ammonia MBE, in which nitrogen is supplied by pyrolysis of NH3 on the sample surface during growth. PA-MBE is typically performed under metal-rich growth conditions, which results in the formation of gallium droplets on the sample surface and a narrow range of conditions for optimal growth. In contrast, high-quality GaN films can be grown by ammonia MBE under an excess nitrogen flux, which in principle should result in improved device uniformity due to the elimination of droplets and wider range of stable growth conditions. A drawback of ammonia MBE, on the other hand, is a serious memory effect of NH3 condensed on the cryo-panels and the vicinity of heaters, which ruins the control of critical growth stages, i.e. the native oxide desorption and the surface reconstruction, and the accurate control of V/III ratio, especially in the initial stage of seed layer growth. In this paper, we demonstrate that the reliable and reproducible growth of GaN on Si (110) substrates is successfully achieved by combining two MBE growth technologies using rf plasma and ammonia and setting a proper growth protocol. Samples were grown in a MBE system equipped with both a nitrogen rf plasma source (SVT) and an ammonia source. The ammonia gas purity was ＞99.9999% and further purified by using a getter filter. The custom-made injector designed to focus the ammonia flux onto the substrate was used for the gas delivery, while aluminum and gallium were provided via conventional effusion cells. The growth sequence to minimize the residual ammonia and subsequent memory effects is the following: (1) Native oxides are desorbed at $750^{\circ}C$ (Fig. (a) for [$1^-10$] and [001] azimuth) (2) 40 nm thick AlN is first grown using nitrogen rf plasma source at $900^{\circ}C$ nder the optimized condition to maintain the layer by layer growth of AlN buffer layer and slightly Al-rich condition. (Fig. (b)) (3) After switching to ammonia source, GaN growth is initiated with different V/III ratio and temperature conditions. A streaky RHEED pattern with an appearance of a weak ($2{\times}2$) reconstruction characteristic of Ga-polarity is observed all along the growth of subsequent GaN layer under optimized conditions. (Fig. (c)) The structural properties as well as dislocation densities as a function of growth conditions have been investigated using symmetrical and asymmetrical x-ray rocking curves. The electrical characteristics as a function of buffer and GaN layer growth conditions as well as the growth sequence will be also discussed. Figure: (a) RHEED pattern after oxide desorption (b) after 40 nm thick AlN growth using nitrogen rf plasma source and (c) after 600 nm thick GaN growth using ammonia source for (upper) [110] and (lower) [001] azimuth.

• Journal of the Korean Vacuum Society
• /
• v.17 no.2
• /
• pp.138-147
• /
• 2008

$SiO_2/TiO_2/ZrO_2$ broadband anti-reflective multi-layer thin films were prepared at room temperature by RF sputtering system. Optical constants and structural properties on each layer of films were analyzed by spectroscopic ellipsometer and transmittance spectra of the films were measured by $UV-V_{is}$ spectrophotometer in the range of 300$\sim$900 nm. To evaluate the films, we compared the measured and analyzed spectra with designed spectra. We investigated influence of discrepancy of thickness and refractive indices of each layer on changes of the transmittance spectra. It was found that refractive indices and shape of dispersion of deposition materials are more contributed to changes of the transmittance spectra than thickness of layer.

• 전자공학회논문지 IE
• /
• v.43 no.2
• /
• pp.11-15
• /
• 2006

In this paper characteristics of polycrystalline silicon crystallized by excimer laser on plastic substrate under 150$^{\circ}C$ is investigated. Amorphous silicon is deposited by rf-magnetron sputter in atmosphere of Ar and He for preventing depletion effect by dehydrogenation as deposition by PECVD. After annealing by 308 nm, 30 Hz, double pulse type XeCl excimer laser, p-chnnel low temperature polycrystalline silicon TFT which maximum mobility is $64cm^2/V{\cdot}s$ at $344mJ/cm^2$ is fabricate.

• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.323-327
• /
• 1998

All solid state lithium based rechargeable batteries were fabricated in a cell structure of Li/PEO-$LiCIO_4$-PC /$LIMn_2O_4$$LIMn_2O_4$ thin films were prepared by RF magnetron sputtering and the spinel structure could be obtained by Rapid Thermal Annealing (RT A) process at the temperature of around 750$750^{\circ}C$ . Room temperature cycling of this cell showed a nearly constant cell potential of 4 V( us. Li) and good reversibility.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.87-92
• /
• 1996

The PLT thin films on (100) cleaved MgO single crystal substrate have been fabricated by rf magnetron sputtering using a PbO-rich target. The dependence of physical and electrical properties on the degree of c-axis orientation has been studied. The degree of c-axis orientation of PLT thin films depends on fabrication conditions. Fabrication conditions of the PLT thin films were such that substrate temperature, working pressure, gas ratio of $Ar/O_{2}$, and rf power density were $640^{\circ}C$, 10 mTorr, 10 seem, and $1.7\;W/cm^{2}$, respectively. In these conditions, the PLT thin film showed the Pb/Ti ratio of 1/2 at the surface, the resistivity of $8{\times}10^{11}{\Omega}{\cdot}cm$, and dielectric constant of 110. The pyroelectric infrared sensors with these PLT thin films showed the peak to peak voltage of 450 m V and signal to noise ratio of 7.2.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.18-22
• /
• 2006

Epitaxial aluminum nitride films on 6H-SiC (0001) were fabricated using reactive RF magnetron sputtering and post-deposition rapid thermal annealing. The electrical properties of AIN films depending on film thickness and measurement temperature have been observed. Full width at half maximum of AIN (0002) was $0.1204^{\circ}$ (about 430 arcsec) X-ray rocking curve results. The equivalent oxide thickness (EOT) of AIN film was estimated as about 10 nm and the leakage current density was within the order of $10^{-8} 4/cm^2$. The dielectric constant of AIN film estimated from the accumulation region of C-V curve measured at $300^{\circ}C$ was 8.3. The dynamic dielectric constant was obtained as 5.1 from J vs. 1/T plots at the temperature ranging from R.T. to $300^{\circ}C$ From above, estimation temperature dependance of the electrical properties of Al/AIN/SiC MIS devices was affirmed and useful data compilation for the reliabilities of SiC MIS is expected.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1382-1384
• /
• 1995

In order to study the structure of RF glow discharge driven at 13.56MHz in argon, the discharge voltage, current and phase shift between them will be measured over a wide range of discharge parameters(gas pressure between 1mTorr and 50mTorr with discharge power between 20mW and 200W). In this paper, the dc glow discharge characteristics and plasma parameters of both FTS and CPMS systems are studied experimentally. It is found that for CPMS system discharge is stablized under wider ranges of magnetic field and pressure than for FTS system. The plasma density and electron temperature of the plasma for these two systems are in the range of $10^{10}{\sim}7{\times}10^{11}[cm^{-3}]$ and $3.5{\sim}6.5$[eV], respectively.