Proceedings of the International Microelectronics And Packaging Society Conference
/
2001.11a
/
pp.146-150
/
2001
Microwave model and high-frequency measurement of the ACF flip-chip interconnection was investigated using a microwave network analysis. S-parameters of on-chip and substrate were separately measured in the frequency range of 200 MHz to 20 GHz using a microwave network analyzer HP8510 and cascade probe. And the cascade transmission matrix conversion was performed. The same measurements and conversion techniques were conducted on the assembled test chip and substrate at the same frequency range. Then impedance values in ACF flip-chip interconnection were extracted from cascade transmission matrix. ACF flip chip interconnection has only below 0.1nH, and very stable up to 13 GHz. Over the 13 GHz, there was significant loss because of epoxy capacitance of ACF. However, the addition of SiO$_2$filler to the ACF lowered the dielectric constant of the ACF materials resulting in an increase of resonance frequency up to 15 GHz. High frequency behavior of metal Au stud bumps was investigated. The resonance frequency of the metal stud bump interconnects is higher than that of ACF flip-chip interconnects and is not observed at the microwave frequency band. The extracted model parameters of adhesive flip chip interconnects were analyzed with the considerations of the characteristics of material and the design guideline of ACA flip chip for high frequency applications was provided.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.46
no.9
/
pp.25-32
/
2009
Recently, research for Network-on-chip(NoC) is progressing. However, due to the increase of system complexity and demand on high performance, conventional copper-based electrical interconnect would be faced with the design limitation of performance, power, and bandwidth. As an alternative to these problems, combined use of Electrical Interconnects(EIs) and Optical Interconnects(OIs) has been introduced. In this paper we propose efficient routing optimization strategy and hybrid switch architecture, which use OIs for critical path and EIs for non-critical path. The proposed method shows up to 25% performance improvement and 38% power reduction.
Yao Jason J.;Chang Keh-Jeng;Chuang Wei-Che;Wang, Jimmy S.
JSTS:Journal of Semiconductor Technology and Science
/
v.5
no.4
/
pp.255-261
/
2005
With the advent of sub-90nm technologies, the system-on-chip (SoC) and system-in-package (SiP) are becoming the trend in delivering low-cost, low-power, and small-form-factor consumer electronic systems running at multiple GHz. The shortened transistor channel length reduces the transistor switching cycles to the range of several picoseconds, yet the time-of-flights of the critical on-chip and off-chip interconnects are in the range of 10 picoseconds for 1.5mm-long wires and 100 picoseconds for 15mm-long wires. Designers realize the bottleneck today often lies at chip-to-chip interconnects and the industry needs a good model to compute the inductance in these parts of circuits. In this paper we propose a new method for extracting accurate equivalent inductance circuit models for SPICE-level circuit simulations of system-on-chip (SoC) and system-in-package (SiP) designs. In our method, geometrical meshes are created and numerical methods are used to find the solutions for the electromagnetic fields over the fine meshes. In this way, multiple-GHz SoC and SiP designers can use accurate inductance modeling and interconnect optimization to achieve high yields.
Park, Kwang-Il;Koo, Ja-Hyuck;Shin, Won-Hwa;Jun, Young-Hyun;Kong, Bai-Sun
JSTS:Journal of Semiconductor Technology and Science
/
v.12
no.2
/
pp.168-174
/
2012
This paper describes a novel global on-chip interconnect scheme, in which a one UI-delayed symbol as well as the current symbol is sent for easing the sensing operation at receiver end. With this approach, the voltage swing on the channel for reliable sensing can be reduced, resulting in performance improvement in terms of power consumption, peak current, and delay spread due to PVT variations, as compared to the conventional repeater insertion schemes. Evaluation for on-chip interconnects having various lengths in a 130 nm CMOS process indicated that the proposed on-chip interconnect scheme achieved a power reduction of up to 71.3%. The peak current during data transmission and the delay spread due to PVT variations were also reduced by as much as 52.1% and 65.3%, respectively.
Journal of the Microelectronics and Packaging Society
/
v.18
no.3
/
pp.53-57
/
2011
In the modern packaging technologies highly condensed metal interconnects are typically formed by highcost processes. These methods inevitably require the precise controls of mutually dependant process parameters, which usually cause the difficulty of the change in the layout design for interconnects of chip to-chip, or chip-to-substrate. In order to overcome these problems, the unique concept and methodology of self-assembly even in micro-meter scale were developed. In this report we focus on the factors which influenced the self-formed bumps by analyzing the phenomenon experimentally. In case of RMA flux, homogenous pattern was obtained in both plain surface and cross-section surface observation. By using RA flux, the phenomena were accelerated although the self-formtion results was inhomogenous. With ussage of moderate RA flux, reaction rate of the self-formation was accelerated with homogeneous pattern.
Ymeri, H.;Nauwelaers, B.;Maex, K.;Roest, D.De;Vandenberghe, S.;Stucchi, M.
JSTS:Journal of Semiconductor Technology and Science
/
v.2
no.1
/
pp.1-6
/
2002
A new closed-form expressions to calculate frequency-dependent distributed inductance and the associated distributed series resistance of single interconnect on a lossy silicon substrate (CMOS technology) are presented. The proposed analytic model for series impedance is based on a self-consistent field method and the vector magnetic potential equation. It is shown that the calculated frequency-dependent distributed inductance and the associated resistance are in good agreement with the results obtained from rigorous full wave solutions and CAD-oriented equivalent-circuit modeling approach.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.41
no.2
/
pp.77-83
/
2004
Cross-talk noise which can occur between on-chip interconnects is significant factor which influence signal integrity. Therefore, this paper presents an analytical method for estimating maximum cross-talk noise. We consider inductance effect of interconnects and use arbitary ramp inputs to estimate noise magnitude exactly. Also, we have used a virtual source for the easy of analytically caculating maximum cross-talk noise from complex cross-talk noise model. The accuracy of the has been shown that be within 4.3 percent maximum relative error compared with the results of HSPICE simulation. Hence, this study can be utilized in various CAD tools for guaranteeing signal integrity.
Level-encoded dual-rail (LEDR) has been widely used in onchip asynchronous interconnects supporting a 2-phase handshake protocol. However, it inevitably requires 2N wires for N-bit data transfers. Encoder and decoder circuits that perform an asynchronous 2-phase handshake protocol with only N wires for N-bit data transfers are presented for on-chip global interconnects. Their fundamentals are based on a ternary encoding scheme using current-mode multiple valued logics. Using 0.25 ${\mu}m$ CMOS technologies, the maximum reduction ratio of the proposed circuits, compared with LEDR in terms of power-delay product, was measured as 39.5% at a wire length of 10 mm and data rate of 100 MHz.
Kim, Ki-Young;Lim, Jae-Ho;Kim, Seok-Yoon;Kim, Deok-Min
The Transactions of The Korean Institute of Electrical Engineers
/
v.59
no.8
/
pp.1406-1415
/
2010
As process technology for semiconductor goes beyond the ultra-deep submicrometer regime, interconnect reliability on a chip has become a serious design concern. As process parameters scale, interconnect widths are reduced rapidly while the current flowing through the interconnect does not decrease in a proportional manner. This trend increases current densities in metal interconnects which may lead to poor reliability for electromigration. Hence, it is critical to estimate the current amount passing through the interconnects earlier in semiconductor design stages. The purpose of this paper is to propose a fast yet accurate current estimation technique that can offer not only analysis time equivalent to those offered by the previous approximation methods but also a relatively precise estimation by using closed-form equations. The accuracy of the proposed technique was confirmed to be about 8 times better on average when compared to the previous work.
Journal of the Korean Institute of Telematics and Electronics C
/
v.36C
no.5
/
pp.13-26
/
1999
This paper presents a metric that can guide to optimal circuit models for interconnects among various models, given interconnect parameters and operating environment. To get this goal, we categorize interconnects into RC~c1ass and RLC-c1ass model domains based on the quantitative modeling error analysis using total resistance, inductance and capacitance of interconnects as well as operating frequency. RC~c1ass circuit models, which include most on~chip interconnects, can be efficiently analyzed by using the model~order reduction techniques. RLC-c1ass circuit models are constructed using one of three candidates, ILC(Iterative Ladder Circuit) macromodels, MC(Method of Characteristics) macromodels, and state-based convolution method, the selection process of which is based upon the allowable modeling error and electrical parameters of interconnects. We propose the model domain diagram leading to optimal circuit models and the division of model domains has been achieved considering the simulation cost of macromodels under the environmental assumption of the general purpose circuit simulator such as SPICE. The macromodeling method presented in this paper keeps the passivity of the original interconnects and accordingly guarantees the unconditional stability of circuit models.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.