• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.197-198
• /
• 2007

In this paper, a 10Gbps Clock and Data Recovery circuit is designed in $0.18{\mu}m$ CMOS Technology. The circuit incorporates a multiphase LC oscillator, a quarter-rate Bang-Bang phase detector, a Charge Pump and a second order loop filter. The simulation results show that the designed circuit has a peak-to-peak clock jitter of 4.1ps and a peak-to-peak recovered data jitter of 8ps while consuming about 44mW from a 1.8V supply.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.3
• /
• pp.255-265
• /
• 2012

This paper presents a 15-GHz multiphase rotary traveling-wave voltage-controlled oscillator (RTW VCO) where a shielded coplanar stripline (CPS) is exploited to provide better shielding protection and lower phase noise at a moderate cost of characteristic impedance and power consumption. Test chips were implemented in a standard 90-nm CMOS process, demonstrating the measured results of 2-GHz frequency tuning range, -11.3-dBm output power, -109.6-dBc/Hz phase noise at 1-MHz offset, and 2-ps RMS clock jitter at 15 GHz. The chip core occupies the area of $0.2mm^2$ and dissipates 12 mW from a single 1.2-V supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.36-42
• /
• 2008

40Gb/s CMOS Clock and Data Recovery circuit design for optical serial link is proposed. The circuit generates 8 multiphase clock using LC tank PLL and controls the phase between the clock and the data using the $2{\times}$ oversampling Bang-Bang PD. 40Gb/s input data is 1:4 demultiplexed and recovered to 4 channel 10Gb/s outputs. The design was progressed to separate the analog power and the digital power. The area of the chip is $2.8{\times}2.4mm^2$ for the inductors and the power dissipation is about 200mW. The chip has been fabricated using 0.18um CMOS process. The measured results show that the chip recovers the data up to 9.5Gb/s per channel(Equivalent to serial input rate of up to 38Gb/s).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.11
• /
• pp.13-22
• /
• 2010

This paper proposed the dual-loops multiphase DLL based mixed VCO/VCDL for a high frequency phase noise suppression of the input clock and the multiple frequencies generation with a precise duty cycle. In the proposed architecture, the dual-loops DLL uses the dual input differential buffer based nMOS source-coupled pairs at the input stage of the mixed VCO/VCDL. This can easily convert the input and output phase transfer of the conventional DLL with bypass pass filter characteristic to the input and output phase transfer of PLL with low pass filter characteristic for the high frequency input phase noise suppression. Also, the proposed DLL can correct the duty-cycle error of multiple frequencies by using only the duty-cycle correction circuits and the phase tracking loop without additional correction controlled loop. At the simulation result with $0.18{\mu}m$ CMOS technology, the output phase noise of the proposed DLL is improved under -13dB for 1GHz input clock with 800MHz input phase noise. Also, at 1GHz operating frequency with 40%~60% duty-cycle error, the duty-cycle error of the multiple frequencies is corrected under $50{\pm}1%$ at 2GHz the input clock.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.2
• /
• pp.73-79
• /
• 2011

This paper describes a reset-free delay-locked loop (DLL) for a memory controller application, with the aid of a hysteresis coarse lock detector. The coarse lock loop in the proposed DLL adjusts the delay between input and output clock within the pull-in range of the main loop phase detector. In addition, it monitors the main loop's lock status by dividing the input clock and counting its multiphase edges. Moreover, by using hysteresis, it controls the coarse lock range, thus reduces jitter. The proposed DLL neither suffers from harmonic lock and stuck problems nor needs an external reset or start-up signal. In a 0.13-${\mu}m$ CMOS process, post-layout simulation demonstrates that, even with a switching supply noise, the peak-to-peak jitter is less than 30 ps over the operating range of 500-1200 MHz. It occupies 0.04 $mm^2$ and dissipates 16.6 mW at 1.2 GHz.

• Journal of IKEEE
• /
• v.8 no.2 s.15
• /
• pp.166-171
• /
• 2004

This paper describes a CMOS time to digital converter (TDC) that measures the interval between two signals and converts to a digital signal. There are various methods to measure the time interval. But several architectures have a limitation in resolution and in conversion time. Moreover, they have complex algorithms. But the proposed TDC circuit has achieved a high resolution (25ps) by using a high-speed digital sampler and simple algorithm. The sampler detects when input signals comes into the TDC and output is coded. The proposed multiphase clock generator was also implemented to achieve 25p resolution.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.433-448
• /
• 2012

A source-synchronous receiver based on a delay-locked loop is presented. It employs a shared global calibration control between channels, yet achieves channel expandability for high aggregate I/O bandwidth. The global calibration control accomplishes skew calibration, equalizer adaptation, and phase lock of all the channels in a calibration period, resulting in the reduced hardware overhead and area of each data lane. In addition, the weight-adjusted dual-interpolating delay cell, which is used in the multiphase DLL, guarantees sufficient phase linearity without using dummy delay cells, while offering a high-frequency operation. The proposed receiver is designed in the 90-nm CMOS technology, and achieves error-free eye openings of more than 0.5 UI across 9-28 inch Nelco4000-6 microstrips at 4-7 Gb/s and more than 0.42 UI at data rates of up to 9 Gb/s. The data lane occupies only $0.152mm^2$ and consumes 69.8 mW, while the rest of the receiver occupies $0.297mm^2$ and consumes 56.0 mW at the 7- Gb/s data-rate and supply voltage of 1.35 V.