• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.337-337
• /
• 2000

This paper describes a Chuck System developed for scaling PDP gas hole on PDP panel glass. There are lots of constraints for designing Chuck System: high temperature, high vacuum, precious motor control etc. A such constraints was considered by design of structure and by selecting of parts and material for Chuck System. The Chuck System was manufactured and assembled after the design process. It was applied on the PDP process unit. For sealing POP hole, precious control of a step motor was important in this system. For this experiment, a step motor, motor driver and micro controller(80196KC) were used.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.389-392
• /
• 2003

A use of micro processor having H-com functions is gradually increased, and this paper describes the digital servo controller applied to linear pulse motor The TMS320LF2407, made by TI(Texas Instruments Co.), is used as a arithmetic unit in control circuit, designed f3r motor drive and available for the implement of high performance and miniaturization. Also, it can allow the sufficient debugging and downloading into control board for independent operation. A current control in order to carry out a position control is of a digital current control mode, and its implement confirmed the servo control performance of position control.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.2
• /
• pp.135-138
• /
• 2011

Although most of control methods have been studied in the continuous-time domain, the actual control systems have been implemented using MCU (Micro Control Unit) and/or microprocessors so that the overall systems turn to be sampled-data systems. In this case, the stability criterion of the closed-loop system is not easy to derive. In this paper, a simple stability criterion for the sampled-data system with sliding mode controller is derived.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.11
• /
• pp.786-795
• /
• 1988

In this paper a boiler control system simulator is designed and inplemeted in order to evaluate performance of the Fault Tolerant Control System. It simulates a boiler control system of a thermal power plant containtng boiler process, peripheral units and analog controller. The simulator uses a low order linear model for boiler first order models for the peripheral unit. Specifically the model of the analog controller is modularized and transformed to digital form if order to be implemented using a micro-processor board. The experimental results show the usability of the developed simulator for the performance test of the FTCS.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.2
• /
• pp.101-107
• /
• 2007

A coaxial rotor flying robot is developed for surveying and reconnoitering various circumstances under calamity environment. The robot has two contrarotating rotors on a common axis, an embedded microcontroller, an IMU(Inertial Measurement Unit), an IR sensor for height control, a micro camera for surveillance, ultrasonic position sensors and wireless communication devices. A bell-bar mounted on the top of the upper rotor hub increases stability and improves flight performance. In this paper, we present a dynamic model of a coaxial rotor flying robot and design an embedded controller far the robot, and implement them to control the developed flying robot. Experimental results show that the proposed controller is valid for autonomous hovering and position control.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.213-219
• /
• 2010

MCU(Micro Controller Unit) used for the automobiles has been required for improving of the safety and high reliability. Also, the necessity of high performance MCU equipped with high fuel-efficiency has been risen according to increased requests of high fuel-efficiency and improving the occupants safety with the development of intelligent vehicles and future vehicles. The MPC5554 32-bit embedded controller, made by Freescale Semiconductor, specialized in the part of the power train provides the high reliability, fast interrupt process and real-time control. In This paper, the investigation on IPMSM using MPC5554 has been performed. Also SVPWM(Space Vector Pulse Width Modulation) is implemented to the servo system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.2
• /
• pp.217-221
• /
• 2001

In this paper, APLC(Active Power Line Conditioner) is designed for low consumed power electrical equipment such as communication electronic equipment, computer sever and etc.. Because APLC which is hunted to the mains controls only the elements of harmonics, the designed APLC is very high efficient. Additionally, controller designed with low cost micro-controller and analog circuit has good merit economically. Simulation and experimental results on a prototype verify the feasibility of the proposed scheme.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.525-526
• /
• 2016

전기자동차 (EV)에서 구동용 모터의 토크 제어를 위한 인버터에는 제어 연산 및 고장 진단 기능을 수행하기 위한 MCU가 있으며, MCU는 상위 제어기 차량 제어 유닛 (VCU)에게 현재 모터 및 인버터의 상태를 주기적으로 전달하고, 현재 차량 주행에 적합한 토크 지령을 받아 토크 제어를 수행하게 된다. 이를 위해 MCU는 전류, 전압 및 위치 센서의 값을 읽어 제어를 수행하게 되며, 제어의 결과 값으로 pulse width modulation (PWM)을 생성하여 이를 통해 모터에 전압을 공급하게 된다. 즉 차량의 구동에 있어 PWM 신호는 가장 중요한 부분이다. 하지만 생산 불량 또는 진동에 의한 납땜 불량 또는 MCU 전원 고장 등으로 MCU에 고장이 발생하게 되면 이상 PWM을 생성하게 되고 정상적인 토크 제어가 불가능해진다. 이때 안전하게 EV를 정지 시키는 알고리즘이 필요하게 되며, 이를 수행 할 supervisor control unit (SCU)가 인버터 컨트롤 보드에 추가되어야 한다. 본 논문에서는 고속으로 주행하던 차량에서 메인 MCU가 고장 날 경우에 안전하게 EV를 정차시키는 방법에 대해 다루었다.

• Journal of Digital Convergence
• /
• v.12 no.12
• /
• pp.257-264
• /
• 2014

Through MCU model, Radio Frequency communication is completed using universal asynchronous receiver and transmitter. The communicatin with PC and MCU is completed using RS-232 cable. At first interconnected communication with PC and MCU is necessary for RF communication because tha UART is based technique for RF communication. Program imbeded in microcontroller unit is ran during RF signal is transmitted to other RF module. Data connected with PC and MCU is transmitted between PC and MCU during PC and MCU is connected.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.7
• /
• pp.1074-1080
• /
• 2015

In the last decades, the increasing interest in unmanned aerial vehicle(UAV) for military, surveillance, and rescue applications made necessary the development of flight control theory and body structure more and more efficient and fast. In this paper, we describe the design and performance of a prototype hexarotor UAV platform featuring an inertial measurement unit(IMU) based autonomous-flying for use in bluetooth communication environments. The proposed system comprises the construction of the test hexarotor platform, the implementation of an IMU, dynamic modeling and simulation in the hexarotor helicopter. Furthermore, the hexarotor helicopter with implemented IMU is connected with a micro controller unit(ARM-cortex) board. The P-PD control algorithm was used to control the hexarotor. We used the Matlab software to help us to tune the P-PD control parameters for quick response and minimizing the fluctuation. The control simulation and experiment on the real system are implemented in the test platform, evaluated and compared against each other.