• Journal of the Semiconductor & Display Technology
• /
• v.15 no.4
• /
• pp.41-45
• /
• 2016

ITO/GZO double layered thin films were prepared on transparent glass substrates. Ga-doped ZnO(GZO) films were deposited by RF magnetron sputtering using an ZnO:Ga (98: 2 wt%) target. The post deposition annealing process was conducted for 30 minutes at different temperature of 100, 200, 300 and $400^{\circ}C$, respectively. As increase annealing temperature, ITO/GZO double layered thin films show the increment of the prefer orientation of ZnO diffraction peak (002) in the XRD patterns. We obtained Ga-doped ZnO thin films with a lowest resistivity of $1.84{\times}10^{-4}{\Omega}-cm$ at $400^{\circ}C$ and transparency above 80% in visible ranges. The figure of merit obtained in this study means that ITO/GZO double layered thin films which annealed at $400^{\circ}C$ have the highest optoelectrical performance in this study.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.143-147
• /
• 2002

In this paper, we investigated the deposition condition of Bragg reflector formation that will be expected to play an important role in future FBAR device applications. The thin films were deposited using an RF/DC magnetron sputtering technique. The material characteristics such as deposition rates, grain structures and surface roughnesses of the deposited silicon dioxide (SiO$_2$) and tungsten (W) films were investigated for various deposition conditions. As a result, it was found that the deposition condition could significantly affect the material characteristics of the deposited films and also the optimization of the deposition process is essentially important to obtain the desirable Brags reflector structure consisted of high-quality in films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.156-157
• /
• 2008

반도체 소자 회로의 집적도가 높아짐에 따라 선폭이 감소하였고 고온 공정이 필요하게 되었다. 기존의 반도체 회로 배선 재료인 Al을 사용할 경우 소자의 속도가 느려져서 소자의 신뢰도가 떨어지고 고온공정에서의 문제가 발생되어 이를 해결하기 위한 차세대 배선 물질로 비저항이 낮은 Cu의 사용이 요구되고 있다. 하지만 Cu는 Si와의 확산이 잘 일어나기 때문에 그 사이에서 확산을 막아주는 확산방지막에 대한 필요성이 제기되었고 연구가 활발히 진행되고 있다. 본 논문에서는 Cu와 Si사이의 확산을 방지하기 위한 W-C-N 확산방지막을 물리적 기상 증착법(PVD)중 하나인 RF Magnetron Sputtering 방식을 사용하여 증착하였다. 고온 공정에서의 안정성을 알아보기 위해 $600^{\circ}C$ 부터 $900^{\circ}C$ 까지 $100^{\circ}C$ 단위로 열처리를 하였고 4-point probe 장치를 사용하여 열처리 온도에 따른 비저항 측정을 통해 W-C-N 확산방지막의 특성을 분석하였다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.5
• /
• pp.457-462
• /
• 2017

This paper proposes a digital power control of the LLC resonant half-bridge inverter for high power microwave oven application. Conventional half-bridge inverter for driving a microwave oven uses a hardware-based power control method which varies the frequency according to the AC source voltage. In this case, it is difficult to control the output power according to the variation of the load status of magnetron. The proposed power control consists of an instantaneous current generator and a current controller. Instantaneous current generator makes an instantaneous current reference from power command using input voltage information. Current controller controls input current which has an information of status of magnetron. The proposed power control does not require any compensation algorithm for the change of the load status of the magnetron and change of input voltage. The validity of the proposed method for the control of the change of input voltage and frequency is verified by both simulation and experiment.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.4
• /
• pp.77-81
• /
• 2010

The AZO thin films were deposited on the corning 1737 glass plate by the RF magnetron sputtering and effects of working pressure and oxygen contents on the electrical properties were investigated. XRD spectra showed a preferred orientation along the c-axis and a minimum FWHM for the 70mTorr. From the surface analysis (AFM), the number of crystal grain of AZO thin film increased as working pressure increased. The film deposited with 70mTorr of working pressure showed n-type semiconductor characteristic having suitable resistivity $-1.59{\times}10^{-2}{\Omega}cm$, carrier concentration $-10.1{\times}10^{19}cm^{-3}$, and mobility $-4.35cm^2V^{-1}s^{-1}$ while other films by 7 mTorr, 20 mTorr of working pressure closed to metallic films. The films including the oxygen represent stoichiometric composition similar to the oxide. The transmittance of the film was over 85% in the visible light range regardless of the changes in working pressure and oxygen contents.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.2
• /
• pp.1-6
• /
• 2012

In this study, a high performance rotary magnet type magnetron source for roll-to-roll sputter system has been developed. We analyzed the density of magnetic field as a function of size variation of the magnet which are in the center and edge of the target. The target efficiency showed the best result when the width of center magnet, the width of edge magnet, the angle of edge magnet, and the rotation angle of Yoke are 20mm, 10mm, $56^{\circ}$, and $16^{\circ}$, respectively. On the basis of the results of magnet array, Roll-to Roll magnetron source was fabricated and tested. The uniformity of the film thickness and that of the sheet resistance was ${\pm}1.62%$ and ${\pm}4.13%$, and the resistivity was $2.79{\times}10^{-3}W{\cdot}cm$.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.556-560
• /
• 2012

Nanocrystalline CrN coatings were deposited by DC and ICP-assisted magnetron sputtering on Si (100) substrates. The influences of the ICP power on the microstructural and crystallographic properties of the coatings were investigated. For the generation of the ICP, radio frequency was applied using a dielectric-encapsulated coil antenna installed inside the deposition chamber. As the ICP power increased from 0 to 500W, the crystalline grain size decreased. It is believed that the decrease in the crystal grain size at higher ICP powers is due to resputtering of the coatings as a result of ion bombardment as well as film densification. The preferential orientation of CrN coatings changed from (111) to (200) with an increase in the ICP power. The ICP magnetron sputtering CrN coatings showed excellent surface roughness compared to the DC magnetron sputtering coatings.

• Journal of Sensor Science and Technology
• /
• v.14 no.2
• /
• pp.63-68
• /
• 2005

The nano-grained Pd or Pt-doped $SnO_{2}$ thin films were deposited on the alumina substrate at ambient temperature or $300^{\circ}C$ by using an R.F. magnetron sputtering system and then annealed at $650^{\cir}C$ for 1 hour or 4 hours in air. The crystallinity and microstructure of the annealed films were analyzed. A grain size of the thin films was 30 nm to 50 nm. As a result of gas sensitivity measurements to an alcohol vapor of $36^{\circ}C$, the 2 wt.% Pt-doped $SnO_{2}$ thin-film sensor deposited at $300^{\circ}C$ and annealed at $650^{\circ}C$ for 4 hours showed the highest sensitivity.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.3
• /
• pp.94-101
• /
• 2008

A new convenient magnet array module is designed to investigate effects of magnetic field array on magnetron discharge characteristics. Magnetic field analysis showed good agreement of measured discharge region by a CCD device which has a high quantum efficiency over visible wavelength range. OES (optical emission spectroscopy) showed major emission peaks are from electronic transitions in 400 nm range and 800 nm range. Effects of driving voltage characteristics were analyzed in a point of electron drift trajectories and ionizing collision frequencies. Pulsed dc with a fast rising and falling time was analyzed to have potential to increase ionization collisions by putting a burst of hot electrons and to raise sheath potential. From measured voltage and current waveform, maximum of -1000 V peak was generated with $-400\;V_{rms}$ conditions. Possibility of a properly designed magnetron cathode was shown to be used as a melting device. Cu was successfully melted with power density of a several tens of $W/cm^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.412-413
• /
• 2007

We report on the electrical, optical, and structural properties of indium zinc tin oxide (IZTO) anode films grown at room temperature on glass substrate. The IZTO anode films grown by a RF magnetron sputtering were investigated as functions of RF power, working pressure, and process time in pure Ar ambient. To investigate electrical, optical and structural properties of IZTO anode films, 4-point probe, Hall measurement, UV/Vis spectrometer, Field Emission Scanning Electron Microscopy (FE-SEM), and X-ray diffraction (XRD) were performed, respectively. A sheet resistance of $13.88\;{\Omega}/{\square}$, average transmittance above 80 % in visible range were obtained from optimized IZTO anode films grown on glass substrate. These results shown the amorphous structure regardless of RF power and working pressure due to low substrate temperature.