• 대한금속재료학회지
• /
• 제46권1호
• /
• pp.33-38
• /
• 2008

The interfacial reactions and shear strength of pure Sn solder bump were investigated with different under bump metallizations (UBMs) and reflow numbers. Two different UBMs were employed in this study: Cu and Ni. Cu6Sn5 and Cu3Sn intermetallic compounds (IMCs) were formed at the bump/Cu UBM interface, whereas only a Ni3Sn4 IMC was formed at the bump/Ni UBM interface. These IMCs grew with increasing reflow number. The growth of the Cu-Sn IMCs was faster than that of the Ni-Sn IMC. These interfacial reactions greatly affected the shear properties of the bumps.

• 한국재료학회지
• /
• 제18권1호
• /
• pp.45-50
• /
• 2008

Microstructural evolution and the intermetallic compound (IMC) growth kinetics in an Au stud bump were studied via isothermal aging at 120, 150, and $180^{\circ}C$ for 300hrs. The $AlAu_4$ phase was observed in an Al pad/Au stud interface, and its thickness was kept constant during the aging treatment. AuSn, $AuSn_2,\;and\;AuSn_4$ phases formed at interface between the Au stud and Sn. $AuSn_2,\;AuSn_2/AuSn_4$, and AuSn phases dominantly grew as the aging time increased at $120^{\circ}C,\;150^{\circ}C,\;and\;180^{\circ}C$, respectively, while $(Au,Cu)_6Sn_5/Cu_3Sn$ phases formed at Sn/Cu interface with a negligible growth rate. Kirkendall voids formed at $AlAu_4/Au$, Au/Au-Sn IMC, and $Cu_3Sn/Cu$ interfaces and propagated continuously as the time increased. The apparent activation energy for the overall growth of the Au-Sn IMC was estimated to be 1.04 eV.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.17-22
• /
• 2016

In terms of mechanical and metallurgical characteristics, the effect of tool plunge depths(0.2, 0.5, 0.7, 1.0, 1.5mm) on weldability in dissimilar Al5083-O/DP590 friction spot joint has been clarified. From the results, it is found that the stirred nugget was stably formed at a plunge depth of more than 0.7mm, which is caused by improved stirring action against each other material. With increasing a plunge depth, the thickness of intermetallic compound(IMC) layer in Al5083-O/DP590 joint has a tendency to increase. The tensile shear strength reaches to the maximum failure load of 6.5kN at a plunge depth of 0.7mm due to relatively small decrease in the thickness of Al5083-O sheet and relatively minute thickness of IMC layer, compared with those of other plunge depth conditions.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.549-554
• /
• 2003

The purpose of this paper is to investigate the solder properties by the change of P mass percentage. Tension test, wetting balance test, spread test, and analysis of intermetallic compound after isothermal aging of Sn-2.5Ag-0.7Cu-0.005P, Sn-2.5Ag-0.7Cu-0.01P, Sn-2.5Ag-0.7Cu-0.02P, Sn-0.7Cu-0.005P were performed. Adding P in the solder alloys resulted in improvement of tensile strength, reduction of intermetallic compound growth, reduction of oxidization in fusible solders under wave soldering. After comparing solder alloy containing P with tin-lead eutectic solder alloy, P contained solders alloys showed much better solder properties than eutectic solder alloy. Furthermore, this solder alloy presented remarkable properties than any other lead-free solder alloy.

• 마이크로전자및패키징학회지
• /
• 제18권2호
• /
• pp.49-55
• /
• 2011

전자기기에서의 고장 중 대부분은 작동 중 발생하는 열과 충격에 기인한다. 이 열과 충격은 PCB(Printed Board) 부품의 접합부 계면에 균열을 야기 시키고, 이 균열은 금속간 화합물(Intermetallic Compound: IMC)의 형성과 밀접한 관계를 가진다. 본 연구에서는 Sn-Ag-Cu계의 Ag함량을 변화한 Sn-1.0Ag-0.5Cu와 Sn-1.2Ag-0.5Cu 및 Sn-3.0Ag-0.5Cu의 3가지 조성의 솔더로 접합한 소재를 대상으로 1000시간 까지 등온시효(Isothermal Aging) 하였다. 등온시효 동 안 솔더(Solder)의 계면에 발생하는 IMC(Intermetallic Compound) 성장이 관찰되었으며, solder 접합부의 기계적 특성은 굽힘충격 시험법을 이용하여 평가되었다. 그 결과 시효처리 전에는 Ag 함량이 낮은 solder의 굽힘충격 특성이 우수하게 나타났으나, 시효처리 후에는 반대의 결과를 나타내었다. 이 결과는 IMC layer 주변에 생성된 미세한 $Ag_3Sn$ 및 조대한 $Cu_6Sn_5$와 관련되어, 미세한 $Ag_3Sn$이 충격을 완화한 것으로 나타나 이에 따라 굽힘충격 특성에 차이가 나타남을 알 수 있었다.

• 마이크로전자및패키징학회지
• /
• 제26권3호
• /
• pp.81-88
• /
• 2019

본 연구에서는 그래핀 산화(graphene oxide, GO) 분말 첨가가 ball grid array(BGA) 패키지와 printed circuit board(PCB)간 Sn-3.0Ag-0.5Cu(SAC305) 무연솔더 접합부의 electromigration(EM) 수명에 미치는 영향에 대하여 보고 하였다. 솔더 접합 직후, Ni/Au표면처리된 패키지 접합계면에서는 $(Cu,Ni)_6Sn_5$가 생성되었으며 organic solderability preservative(OSP) 표면처리 된 PCB 접합계면에서는 $Cu_6Sn_5$ 금속간화합물(intermetallic compound, IMC)이 생성되었다. $130^{\circ}C$, $1.0{\times}10^3A/cm^2$ 전류밀도 하에서 EM 수명평가 결과, GO를 첨가하지 않은 솔더 접합부의 평균 파괴 시간은 189.9 hrs으로 도출되었고, GO를 첨가한 솔더 접합부의 평균 파괴 시간은 367.1 hrs으로 도출되었다. EM에 의한 손상은 패키지 접합계면에 비하여 pad 직경이 작은 PCB 접합계면에서 전자 유입에 의한 Cu의 소모로 인하여 발생하였다. 한편, 첨가된 GO는 하부계면의 $Cu_6Sn_5$ IMC와 솔더 사이에 분포하는 것을 확인하였다. 따라서, SAC305 무연솔더에 첨가된 GO가 전류 집중 영역에서 Cu의 빠른 확산을 억제하여 우수한 EM 신뢰성을 갖는 것으로 생각된다.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.134-141
• /
• 2013

Reflow soldering process is essential in electronic package. Reflow process for a long time results from the decrease of reliability because IMC is formed excessively. Solder alloys of Sn-37Pb and Sn-Ag with different kinds of Cu contents (0, 0.5 and 1 wt.%) as compared with Ni and Cu plate joints are investigated according to varying reflow time. The interfaces of solder joints are observed to analyze IMC (intermetallic compound) growth rate by scanning electron microscope (SEM). Shear test is also performed by using SP (Share-Punch) tester. The test results are compared with the solder joints of two different plates (Ni and Cu plate). $Cu_6Sn_5$ IMCs are formed on Cu plate interfaces after reflows in all samples. Ni3Sn4 and $(Cu,Ni)_6Sn_5$ IMCs are also formed on Ni plate interfaces. The IMC layer forms are affected by reflow time and contents of solder alloy. These results show that mechanical strength of solder joints strongly depends on thickness and shape of IMC.

• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.145-153
• /
• 2013

In this study, shear punch-creep (SP-Creep) at Sn-4Ag/Cu pad the joint was tested by using environment-friendly Pb-free solder alloy Sn-4Ag of electronic components. Pb eutectic alloy (Sn-37Pb) joints limited to environmental issues with reflow time (10sec, 30sec, 100sec, 300sec) according to two types of solder alloy joints are compared and evaluated by creep strain rate, rupture time and IMC (Intermetallic Compound) behavior. As the results, reflow time increases with increasing thickness of IMC can be seen at overall 100sec later in case of two solder joints on the IMC thickness of Sn-4Ag solder joints thicker than Sn-37Pb solder joints. In addition, when considering creep evaluation factors, lead-free solder alloy Sn-4Ag has excellent creep resistance more than Pb eutectic alloy. For this reason, the two solder joints, such as in the IMC (Cu6Sn5) was formed. However, the creep resistance of Sn-4Ag solder joints was largely increased in the precipitation strengthening effect of dispersed Ag3Sn with interface more than Sn-37Pb solder joints.

• 대한금속재료학회지
• /
• 제47권3호
• /
• pp.202-208
• /
• 2009

The effects of aging time on the microstructure and shear strength of the Low Temperature Co-fired Ceramic (LTCC)/Ag pad/Electroless Nickel Immersion Gold (ENIG)/BGA solder joints were investigated through isothermal aging at $150^{\circ}C$ for 1000 h with conventional Sn-37Pb and Sn-3Ag-0.5Cu. $Ni_3Sn_4$ intermetallic compound (IMC) layers was formed at the interface between Sn-37Pb solder and LTCC substrate as-reflowed state, while $(Ni,Cu)_3Sn_4$ IMC layer was formed between Sn-3Ag-0.5Cu solder and LTCC substrate. Additional $(Cu,Ni)_6Sn_5$ layer was found at the interface between the $(Ni,Cu)_3Sn_4$ layer and Sn-3Ag-0.5Cu solder after aging at $150^{\circ}C$ for 500 h. Thickness of the IMC layers increased and coarsened with increasing aging time. Shear strength of both solder joints increased with increasing aging time. Failure mode of BGA solder joints with LTCC substrate after shear testing revealed that shear strength of the joints depended on the adhesion between Ag metallization and LTCC. Fracture mechanism of Sn-37Pb solder joint was a mixture of ductile and pad lift, while that of Sn-3Ag-0.5Cu solder joint was a mixture of ductile and brittle $(Ni,Cu)_3Sn_4$ IMC fracture morphology. Failure mechanisms of LTCC/Ag pad/ENIG/BGA solder joints were also interpreted by finite element analyses.

• 한국전기전자재료학회논문지
• /
• 제17권3호
• /
• pp.267-271
• /
• 2004

The joint strength and fracture surface of Sn-Pb solder bump in photo diode packages after isothermal aging testing were studied experimentally. Cu/Sn-Pb solders were adopted, and aged for up to 900 hours at 12$0^{\circ}C$ and 17$0^{\circ}C$ to analyze the effect of intermetallic compound(IMC). In 900-hour aging experiments, the maximum shea strength of Sn-Pb solder decreased by 20％ and 9％. The diffraction patterns of Cu$_{6}$Sn$_{5}$, scallop-shape IMC, and planar-shape Cu$_3$Sn were observed by Transmission Electron Microscopy (TEM).EM).