• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.21-29
• /
• 2004

Hot carrier degradation characteristics of Nano-scale CMOSFETs with dual gate oxide have been analyzed in depth. It is shown that, PMOSFET lifetime dominate the device lifetime than NMOSFET In Nano-scale CMOSFETs, that is, PMOSFET lifetime under CHC (Channel Hot Carrier) stress is much lower than NMOSFET lifetime under DAHC (Dram Avalanche Hot Carrier) stress. (In case of thin MOSFET, CHC stress showed severe degradation than DAHC for PMOSFET and DAHC than CHC for NMOSFET as well known.) Therefore, the interface trap generation due to enhanced hot hole injection will become a dominant degradation factor in upcoming Nano-scale CMOSFET technology. In case of PMOSFETs, CHC shows enhanced degradation than DAHC regardless of thin and thick PMOSFETs. However, what is important is that hot hole injection rather than hot electron injection play a important role in PMOSFET degradation i.e. threshold voltage increases and saturation drain current decreases due to the hot carrier stresses for both thin and thick PMOSFET. In case of thick MOSFET, the degradation by hot carrier is confirmed using charge pumping current method. Therefore, suppression of PMOSFET hot carrier degradation or hot hole injection is highly necessary to enhance overall device lifetime or circuit lifetime in Nano-scale CMOSFET technology

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.169-172
• /
• 2020

In this paper, the effect of hot carrier injection on an n-bulk fin field-effect transistor (FinFET) is analyzed. The hot carrier injection method is applied to determine the performance change after injection in two ways, channel hot electron (CHE) and drain avalanche hot carrier (DAHC), which have the greatest effect at room temperature. The optimum condition for CHE injection is V_G=V_D, and the optimal condition for DAHC injection can be indirectly confirmed by measuring the peak value of the substrate current. Deterioration by DAHC injection affects not only hot electrons formed by impact ionization, but also hot holes, which has a greater impact on reliability than CHE. Further, we test the amount of drain voltage that can be withstood, and extracted the lifetime of the device. Under CHE injection conditions, the drain voltage was able to maintain a lifetime of more than 10 years at a maximum of 1.25 V, while DAHC was able to achieve a lifetime exceeding 10 years at a 1.05-V drain voltage, which is 0.2 V lower than that of CHE injection conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.9
• /
• pp.683-686
• /
• 1998

Hot carrier effects as a function of bias stress time and bias stress consitions were syste-matically investigated in p-channel poly-Si TFT s fabricated on the quartz substrate. The device degradation was observed for the negative bias stress, while improvement of electrical characteristic except for subthreshold slope was observed for the positive bias stress. It was found that these results were related to the hot-carrier injection into the gate oxide and interface states at the poly-Si/$SiO_2$interface rather than defects states generation within the poly-Si active layer under bias stress.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.12
• /
• pp.77-87
• /
• 1993

PMOSFETs were studied on the effect of Hot-Carrier induced drain leakage current (Gate-Induced-Drain-Leakage). The result turned out that change in Vgl(drain voltage where 1pA/$\mu$m of drain leadage current flows) was largest in the Channel-Hot-Hole(CHH) injection condition and next was in dynamic stress and was smallest in electron trapping (Igmax) condition under various stress conditions. It was analyzed that if electron trapping occurrs in the overlap region of gate and drain(G/D), it reduces GIDL current due to increment of flat-band voltage(Vfb) and if CHH is injected, interface states(Nit) were generated and it increases GIDL current due to band-to-defect-tunneling(BTDT). Especially, under dynamic stress it was confirmed that increase in GIDL current will be high when electron injection was small and CHH injection was large. Therefore as applying to real circuit, low drain voltage GIDL(BTDT) was enhaced as large as CHH Region under various operating voltage, and it will affect the reliablity of the circuit.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.8
• /
• pp.847-852
• /
• 2014

As the scaling trend becomes accelerated in process technology for cost reduction in semiconductor chip manufacturing, the requirement for shrink technology has increased. Hot Carrier Injection (HCI) degradation for I/O transistors is most concerning part when shrink. To solve this, the effective channel length (Leff) was increased using liner oxide before Light Doped Drain (LDD) implants and optimized the tilt angle to increase Leff without E-field degradation in LDD region, satisfying the HCI specification.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.327-330
• /
• 2004

It is shown that the hot carrier degradation due to enhanced hot holes trapping dominates PMOSFETs lifetime both in thin and thick devices. Moreover, it is found that in 0.13 ${\mu}m$ CMOSFET the PMOS lifetime under CHC (Channel Hot Carrier) stress is lower than the NMOSFET lifetime under DAHC (Drain Avalanche Hot Carrier) stress. Therefore. the interface trap generation due to enhanced hot hole injection will become a dominant degradation factor. In case of thick MOSFET, the degradation by hot carrier is confirmed using charge pumping current method and highly necessary to enhance overall device lifetime or circuit lifetime in upcoming nano-scale CMOS technology.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.357-361
• /
• 1995

An experiment on characteristics of nMOSFET's in the long stress condition with the maximum of the substrate current has been carried out in order to study on the degradation due to the hot-carrier effect. Based on the measured result of the threshold voltage, the damage is mostly due to the hole injection into the oxide. After long stress, it was shown that the drain current increased at low gate voltages and hence decreased at high gate voltages.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.687-694
• /
• 2008

This paper is focused on the improvement of MOS device reliability related to deuterium process. The injection of deuterium into the gate oxide film was achieved through two kind of method, high-pressure annealing and low-energy implantation at the back-end of line, for the purpose of the passivation of dangling bonds at $SiO_2/Si$ interface. Experimental results are presented for the degradation of 3-nm-thick gate oxide ($SiO_2$) under both negative-bias temperature instability (NBTI) and hot-carrier injection (HCI) stresses using P and NMOSFETs. Annealing process was rather difficult to control the concentration of deuterium. Because when the concentration of deuterium is redundant in gate oxide excess traps are generated and degrades the performance, we found annealing process did not show the improved characteristics in device reliability, compared to conventional process. However, deuterium ion implantation at the back-end process was effective method for the fabrication of the deuterated gate oxide. Device parameter variations under the electrical stresses depend on the deuterium concentration and are improved by low-energy deuterium implantation, compared to conventional process. Our result suggests the novel method to incorporate deuterium in the MOS structure for the reliability.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.7
• /
• pp.780-790
• /
• 1988

We have studied the hot-carrier-induced degradation caused by the high channel electric field due to the decrease of the gate length of MOSFET used in VLSI. Under DC stress, the condition in which maximum substrate current occures gave the worst degradation. Under AC dynamic stress, other conditions, the pulse shape and the falling rate, gave enormous effects on the degradation phenomena, especially at 77K. Threshold voltage, transconductance, channel conductance and gate current were measured and compared under various stress conditions. The threshold voltage was almost completely recovered by hot-injection stress as a reverse-stress. But, the transconductance was rapidly degraded under hot-hole injection and recovered by sequential hot-electron stress. The Si-SiO2 interface state density was analyzed by a charge pumping technique and the charge pumping current showed the same trend as the threshold voltage shift in degradation process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.266-269
• /
• 1997

Hot carrier effects as a function of bias stress time and bias stress conditions were syste-matica1ly investigated in p-channel po1y-Si TFT's fabricated on the quartz substrate. The device degradation was observed for the negative bias stress. After positive bias stressing, Improvement of electrical characteristic except for subthreshold slope was observed. It was found that these results were related to the hot carrier injection into the gate oxide and interface states at the poly-Si/SiO$_2$interface rather than defects states generation under bias stress.