• Nuclear Engineering and Technology
• /
• v.56 no.4
• /
• pp.1532-1537
• /
• 2024

Time-of-flight (TOF) PET detectors with fast-rise-time scintillators and fast-single photon time resolution silicon photomultiplier (SiPM) have been developed to improve the coincidence timing resolution (CTR) to sub-100 ps. The CTR can be further improved with an optimal bandwidth and minimized electronic noise in the readout circuit and this helps reduce the distortion of the fast signals generated from the TOF-PET detector. The purpose of this study was to develop an ultra-high frequency and fully-differential (UF-FD) readout circuit that minimizes distortion in the fast signals produced using TOF-PET detectors, and suppresses the impact of the electronic noise generated from the detector and front-end readout circuits. The proposed UF-FD readout circuit is composed of two differential amplifiers (time) and a current feedback operational amplifier (energy). The ultra-high frequency differential (7 GHz) amplifiers can reduce the common ground noise in the fully-differential mode and minimize the distortion in the fast signal. The CTR and energy resolution were measured to evaluate the performance of the UF-FD readout circuit. These results were compared with those obtained from a high-frequency and single ended readout circuit. The experiment results indicated that the UF-FD readout circuit proposed in this study could substantially improve the best achievable CTR of TOF-PET detectors.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.836-845
• /
• 2001

A Novel fully-differential bipolar current subtracter(FCS) and its application to current controlled current amplifier(CCCA) for high-accuracy current-mode signal processing were designed. To obtain full-differential current output, the FCS was symmetrically composed of two current follower with low current-input impedance. The CCCA to control output current by the bias current was consisted of the subtracter and a current gain amplifier(CGA) with single-ended current output.. The simulation result shows that the FCS has current-input impedance of 5 Ω and a good linearity. The CCCA has 3-dB cutoff frequency of 20 MHz for the range over bias current 100 $\mu$A to 20 mA. The power dissipation of the FCS and CCCA are 1.8 mW and 3 mW, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.1
• /
• pp.7-18
• /
• 2002

Single-ended differential RF circuit topologies fully utilizing complementary characteristics of both NMOS and PMOS are proposed, which have inherent advantage of both single-ended and differential circuits. Using this concept, we propose a CCPP (Complementary CMOS parallel push-pull) amplifier which has single-ended input/output with differential amplifying characteristics, leading to more than 30 dB improvement on $IIP_2$. In addition, complementary resistive mixer is also proposed, which provides not only differential IF outputs from single-ended RF input, but much better linearity as well as isolation characteristics. Experimental results using $0.35{\;}\mu\textrm{m}$ CMOS process show that, compared with conventional NMOS resistive mixer, the proposed mixer shows 15 dB better LO-to-IF isolation, 4.6 dB better $IIP_2$, and 4.5 dB better $IIP_3$performances.

• ETRI Journal
• /
• v.29 no.4
• /
• pp.421-429
• /
• 2007

This paper presents a direct-conversion CMOS transceiver for fully digital DS-UWB systems. The transceiver includes all of the radio building blocks, such as a T/R switch, a low noise amplifier, an I/Q demodulator, a low pass filter, a variable gain amplifier as a receiver, the same receiver blocks as a transmitter including a phase-locked loop (PLL), and a voltage controlled oscillator (VCO). A single-ended-to-differential converter is implemented in the down-conversion mixer and a differential-to-single-ended converter is implemented in the driver amplifier stage. The chip is fabricated on a 9.0 $mm^2$ die using standard 0.18 ${\mu}m$ CMOS technology and a 64-pin MicroLead Frame package. Experimental results show the total current consumption is 143 mA including the PLL and VCO. The chip has a 3.5 dB receiver gain flatness at the 660 MHz bandwidth. These results indicate that the architecture and circuits are adaptable to the implementation of a wideband, low-power, and high-speed wireless personal area network.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.159-162
• /
• 2000

Novel simulated floating inductor (SFI) using fully-differential operational transconductance amplifier (FOTA) is presented. The SFI only consists of two FOTA and a capacitor. A ladder-type third-order elliptic low-pass filter is also presented for the SFI’s application. The theory of operations described and the simulation results are used to verify theoretical predictions. The SFI shows close agreement between predicted behavior and simulation performance. The simulation results that the SFI have The temperature coefficient of-179 ppm/$^{\circ}C$ and Q factor of 120 at 200kHz at supply voltage ${\pm}$5 V.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.89-93
• /
• 2007

This paper presents the design and the implementation of input/output (I/O) interface circuits for 2.5 Gbps operation in a 3.3V 0.35um CMOS technology. Due to the differential transmission technique and low voltage swing, LVDS(low-voltage differential signaling) has been widely used for high speed transmission with low power consumption. This interface circuit is fully compatible with the LVDS standard. The LVDS proposed in this paper utilizes a telescopic amplifier. This circuit is operated up to 2.3 Gbps. The circuit has a power consumption of 25. 5mW. This circuit is designed with Samsung $0.35{\mu}m$ CMOS process. The validity and effectiveness are verified through the HSPICE simulation.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.4
• /
• pp.309-315
• /
• 2010

A fully-differential low-voltage low-power electrocardiogram (ECG) amplifier by using the nonfeedback PMOS pseudo-resistors is proposed. It consists of two operational-transconductance amplifiers (OTA) in series (a preamplifier and a variable-gain amplifier). To make it insensitive to the gate leakage current of the OTA input transistor, the feedback pseudo-resistor of the conventional ECG amplifier is moved to input branch between the OP amp summing node and the DC reference voltage. Also, an OTA circuit with a Gm boosting block without reducing the output resistance (Ro) is proposed to maximize the OTA DC gain. The measurements shows the frequency bandwidth from 7 Hz to 480 Hz, the midband gain programmable from 48.7 dB to 59.5 dB, the total harmonic distortion (THD) less than 1.21% with a full voltage swing, and the power consumption of 233 nW in a 0.13 ${\mu}m$ CMOS process at the supply voltage of 0.7 V.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.768-776
• /
• 2014

Using a simplified high-frequency small-signal equivalent circuit model for BSIM3 MOSFET, the fully differential two-stage folded-cascode CMOS operational amplifier is analyzed to obtain its small-signal voltage transfer function. As a result, the expressions for dc gain, five zero frequencies, five pole frequencies, unity-gain frequency, and phase margin are derived for op amp design using design equations. Then the analysis result is verified through the comparison with Spice simulations of both a high speed op amp and a low power op amp designed for the $0.13{\mu}m$ CMOS process.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.4
• /
• pp.251-257
• /
• 2015

This work presents modelling and simulation of a readout integrated circuit (ROIC) design considering pair-wise serial configuration along with thermal modeling of an uncooled microbolometer array. A fully differential approach is used at the input stage in order to reduce fixed pattern noise due to the process variation and self-heating-related issues. Each pair of microbolometers is pulse-biased such that they both fall under the same self-heating point along the self-heating trend line. A ${\pm}10%$ process variation is considered. The proposed design is simulated with a reference input image consisting of an array of $127{\times}92$ pixels. This configuration uses only one unity gain differential amplifier along with a single 14-bit analog-to-digital converter in order to minimize the dynamic range requirement of the ROIC.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.143-152
• /
• 2004

A novel low-power wideband bipolar second-generation current conveyors(CCIIs) and its application to universal instrumentation amplifier(UIA) were proposed. The CCII for accuracy voltage or current transfer characteristics and low current input impedance adopted adaptive current bias circuit into conventional class Ab CCII. The UIA consists of only two CCIIs and four resistors. Three instrumentation function of the UIA can be realized by selection of input signals and resistors. The simulation results show that the CCII has input impedance of 2.0$\Omega$ and the voltage gain of 60㏈ for frequency range from 0 to 50KHz when used as a voltage amplifier. The CCII has also good characteristics of current follower for current range from -100㎃ to ＋100㎃. The simulation results show that the UIA has three instrumentation amplifier functions without resistor matching. The UIA has the voltage gain of 40㏈ for frequency range from 0 to 100KHz when used as a fully-differential instrumentation amplifier. The power dissipations of the CCII and the UIA are 0.75㎽ and 1.5㎽ at supply voltage of $\pm$2.5V, respectively.