• Journal of Semiconductor Engineering
• /
• v.2 no.1
• /
• pp.109-118
• /
• 2021

This review paper describes the overall operating principle of a discrete-time delta-sigma modulator (DTDSM) and a continuous-time delta-sigma modulator (CTDSM) using a switched-capacitor (SC). In addition, research that has solved the problems related to each delta-sigma modulator (DSM) is introduced, and the latest developments are explained. This paper describes the chopper-stabilization technique that mitigates flicker noise, which is crucial for the DSM. In the case of DTDSM, this paper addresses the problems that arise when using SC circuits and explains the importance of the operational transconductance amplifier performance of the first integrator of the DSM. In the case of CTDSM, research that has reduced power consumption, and addresses the problems of clock jitter and excess loop delay is described. The recent developments of the analog front end, which have become important due to the increasing use of wireless sensors, is also described. In addition, this paper presents the advantages and disadvantages of the three-opamp instrumentation amplifier (IA), current feedback IA (CFIA), resistive feedback IA, and capacitively coupled IA (CCIA) methods for implementing instrumentation amplifiers in AFEs.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.4
• /
• pp.233-239
• /
• 2009

A mixed CT/DT 2-1 cascaded ${\Sigma\Delta}M$ which includes a first stage CT ${\Sigma\Delta}M$ and a second stage mismatch insensitive two-channel time-interleaved DT ${\Sigma\Delta}M$ is proposed. With this approach, the advantages of both CT and DT ${\Sigma\Delta}Ms$ including high speed operation, inherent anti-aliasing filter, and good coefficient matching can be achieved. The two-channel time-interleaved ${\Sigma\Delta}M$ used in the second stage alleviates the speed constraints of the DT ${\Sigma\Delta}M$, whereas enables better matching between the analog and digital filter coefficients compared to CT ${\Sigma\Delta}Ms$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.26-32
• /
• 2017

This paper presents a low power and high resolution incremental delta-sigma ADC that utilizes a passive integrator instead of an opamp-based active integrator. Opamp is a power-hungry block that involves tight design tradeoffs. To avoid the use of active integrator, the s-domain characteristic of an active integrator is first analyzed. Based on the analysis, an active integrator with low gain design is proposed as an alternative design method. To save power even more aggressively, a passive integrator with no static current is proposed. A 1st order single-bit incremental delta-sigma ADC using the proposed passive integrator is implemented in a 65nm CMOS process. Transistor-level simulation shows that the ADC consumes only 0.6uW under 1.2V supply while achieving SNDR of 71dB with 22kHz bandwidth. The estimated total power consumption including digital filter is 6.25uW, and resulting power efficiency is on a par with state-of-the-art A/D converters.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.148-158
• /
• 2012

This paper presents the design of the incremental delta-sigma ADC. The proposed circuit consists of pre-amplifier, S & H circuit, MUX, delta-sigma modulator, and decimation filter. Third-order discrete-time delta-sigma modulator with 1-bit quantization were fabricated by a $0.18{\mu}m$ CMOS technology. The designed circuit show that the modulator achieves 87.8 dB signal-to-noise and distortion ratio (SNDR) over a 5 kHz signal bandwidth and differential nonlinearity (DNL) of ${\pm}0.25$ LSB, integral nonlinearity (INL) of ${\pm}0.2$ LSB. Power consumption of delta-sigma modulator is $941.6{\mu}W$. It was decided that N cycles are 200 clock for 16-bits output.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.461-468
• /
• 2019

A continuous-time Delta-Sigma ADC has various benefits; it does not require an explicit anti-aliasing filter, and it is able to handle wider-band signals with less power consumption in comparison with a discrete-time Delta-Sigma ADC. However, it inherently needs to sample the signal with a high-speed clock, necessitating a complex decimation filter that operates at high speed in order to convert the modulator output to a low-rate high-resolution digital signals without causing aliasing. This paper proposes a continuous-time Delta-Sigma ADC architecture that employs pulse-width modulation and shows that the proposed architecture lends itself to a simpler implementation of the decimation filter using a lookup table.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.10
• /
• pp.6-14
• /
• 2011

This paper presents the design of the battery sensor IC for instrumentation of current, voltage using delta-sigma ADC. The proposed circuit consists of programmable gain instrumentation amplifier (PGIA) and second-order discrete-time delta-sigma modulator with 1-bit quantization were fabricated by a 0.25 ${\mu}m$ CMOS technology. Design circuit show that the modulator achieves 82 dB signal-to-noise ratio (SNR) over a 2 kHz signal bandwidth with an oversampling ratio (OSR) of 256 and differential nonlinearity (DNL) of ${\pm}$ 0.3 LSB, integral nonlinearity (INL) of ${\pm}$ 0.5 LSB. Power consumption is 4.5 mW.