• KIPS Transactions on Computer and Communication Systems
• /
• v.4 no.9
• /
• pp.321-326
• /
• 2015

In this paper, we proposed an algorithm which could transmit reliable data between smart devices by using inaudible high frequency of audible frequency range and cyclic redundancy check method. The proposed method uses 18 kHz~22 kHz as high frequency which inner speaker of smart device can make a sound in audible frequency range (20 Hz~22 kHz). To increase transmission quantity of data, we send mixed various frequencies at high frequency range 1 (18.0 kHz~21.2 kHz). At the same time, to increase accuracy of transmission data, we send some mixed frequencies at high frequency range 2 (21.2 kHz~22.0 kHz) as checksum. We did experiments about data transmission between smart devices by using the proposed method to confirm data transmission speed and accuracy of the proposed method. From the experiments, we showed that the proposed method could transmit 32 bits data in 235 ms, the transmission success rate was 99.47%, and error detection by using cyclic redundancy check was 0.53%. Therefore, the proposed method will be a useful for wireless transmission technology between smart devices.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.1101-1107
• /
• 2004

This paper presents an optimization algorithm and technique for designing parallel Cyclic Redundancy Check (CRC) circuit, which is most widely adopted for error detection A new heuristic algorithm is developed to find as many shared terms as possible, thus eventually to minimize the number and level of the exclusive-or logic blocks in parallel CRC circuits. 16-bit and 32-bit CRC generators are designed with different types of Programmable Logic Devices, and it has been found that our new algorithm and architecture significantly reduce the delay.

• Journal of IKEEE
• /
• v.21 no.2
• /
• pp.130-135
• /
• 2017

Normally, in data transmission, extra parity bits are added to the input message which were derived from its input and a pre-defined algorithm. The same algorithm is used by the receiver to check the consistency of the delivered information, to determine if it is corrupted or not. It recovers and compares the received information, to provide matching and correcting the corrupted transmitted bits if there is any. This paper aims the following objectives: to use an alternative error detection-correction method, to lessens both the fixed number of the required redundancy bits 'r' in cyclic redundancy checking (CRC) because of the required polynomial generator and the overhead of interspersing the r in Hamming code. The experimental results were synthesized using Xilinx Virtex-5 FPGA and showed a significant increase in both the transmission rate and detection of random errors. Moreover, this proposal can be a better option for detecting and correcting errors.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.1
• /
• pp.83-91
• /
• 1993

In the digital transmission system, cyclic redundancy check(CRC) code is widely used because it is easy to be implemented and has good performance in error detection. CRC code generator consists of several shift registers and modulo 2 adders. After manipulation of input data stream in the encoder, the remaining value of shift registers becomes CRC code. At the receiving side, error can be detected and corrected by CRC codes immediately transmitted after data stream. But, in the high speed system such as an A TM switch, it is difficult to implement the serial CRC encoder because of speed limitation of available semiconductor devices. In this paper, we propose the efficient parallel CRC encoder and syndrome calculator to solve the speed problem in implementing these functions using the existing semiconductor technology.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1235-1240
• /
• 2004

This paper has presented the parallel cyclic redundancy check (CRC) technique that performs CRC computation in parallel superior to the conventional CRC technique that processes data bits serially. Also, it has showed that the implemented parallel CRC circuit had been successfully applied to the inductively coupled passive RFID system working at a frequency of 13.56MHz in order to process the detection of logical faults more fast and the system had been verified experimentally. In comparison with previous works, the proposed RFID system using the parallel CRC technique has been shown to reduce the latency and increase the data processing rates in the results. Therefore, it seems reasonable to conclude that the parallel CRC realization in the RFID system offers a means of maintaining the integrity of data in the high speed RFID system.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1184-1187
• /
• 2020

This paper proposes an in-vehicle network controller fully exploiting the advantages of UART (Universal Asynchronous Receiver/Transmitter) and CAN (Controller Area Network). UART is used in 1-to-1 communication and it exploits parity bit for data integrity check. The proposed in-vehicle network controller converts UART into CAN, which enables multiple communications along with 1-to-1 communication. Also, the proposed in-vehicle network controller exploits CRC (cyclic redundancy check) for data integrity check, which increases communication reliability. CAN is controlled by microprocessor, but the proposed in-vehicle network controller can be controlled by any devices compliant with RS-232, RS-422, and RS-485.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.6A
• /
• pp.519-536
• /
• 2007

In this paper, we combine the Hybrid-Automatic Repeat reQuest (HARQ) algorithm with joint Tx and Rx antenna selection based on the reliability of the individual antennas links. The cyclic redundancy check (CRC) is applied on the data before being encoded using the Turbo encoder. In the receiver the CRC is used to detect errors of each antenna stream and to decide whether a retransmission is required or not. The receiver feeds back the transmitter with the Tx antennas ordering and the acknowledgement of each antenna (ACK or NACK). If the number of ACK antennas is higher than the NACK antennas, then the retransmission takes place from the ACK antennas using the Chase Combining (CC). If the number of the NACK antennas is higher than the ACK antennas then the ACK antennas are used to retransmit the data streams using the CC algorithm and additional NACK antennas are used to retransmit the remaining streams using Incremental Redundancy (IR, i.e. the encoder rate is reduced). Furthermore, the HARQ is used with the I-BLAST (Iterative-BLAST) which grantees a high transmission rate.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.533-536
• /
• 2003

본 논문에서는 전화선을 이용한 고속 홈네트워크인 HomePNA 2.0 시스템에서 HomePNA 2.0 (H2) 프레임을 만들기 위한 프레임 프로세싱 중, 다항식 나누기 연산을 통한 CRC (Cyclic Redundancy Check) 16비트 생성, HCS (Header Check Sequence) 8비트 생성 및 혼화(Scrambling) 처리에 있어서 입력 8 비트를 동시에 병렬 처리함으로써 기존의 1 비트 입력을 LFSR (Linear Feedback Shift Register)를 사용한 다항식 나누기 연산을 수행했을 때보다 빠른 속도로 H2 프레임을 구현하고자 하는 고속 처리 기법을 제시하고 이의 성능을 검증하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.11
• /
• pp.1655-1662
• /
• 1993

In this paper we discuss three algorithms-Direct, Successive, and Recursive-on parallel CRC(Cyclic Redundancy Check) verification. The algorithms are derived by combining the byte-syndromes precomputed from the generator polynomial. These algorithms are compared in terms of the amount of hardware and the speed of operation. Since the algorithms can be generalized easily, we took the ATM cell delineation example for easier description. As an application of the algorithm Recursive, an ATM cell delineation module suitable for STM-1 transmission has been successfully realized through commercially available field programmable gate arrays.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.437-444
• /
• 2022

This paper proposes a CRC error verification method for SPI and I2C buses of automotive semiconductors. In automotive semiconductors, when an error occurs in communication and an incorrect value is transmitted, fatal results may occur. Unlike LIN communication and CAN communication, in communication such as SPI and I2C, there is no frame for detecting an error, so some definitions of new standards are required. Therefore, in this paper, the CRC error detection mode is newly defined in the SPI and I2C communication protocols, and the verification is presented by designing it in hardware.