• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.10A
• /
• pp.1571-1578
• /
• 1999

In this paper, we present the Modulator Channel Card and VLSI chip for the Radio Transceiver Unit (RTU) of direct sequence code division multiple access (DS-CDMA) Wireless Local Loop (WLL) System. The Modulator Channel Card is designed and implemented using ASIC's, FPGA's and DSP's. The ASIC, compliance with Common Air Interface specification proposed by ETRI, has 40K gates which is designed to operate at 32MHz, and is fabricated using $0.6\mu\textrm{m}$ CMOS process. The ASIC carries out for I- or Q- phase data channel signal processing at a time, where each data channel processing consists of channel coding, block interleaving, scrambling, Walsh modulation, Pseudo-Noise (PN) spreading, and baseband filtering. The Modulator Channel Card has been integrated as a part of RTU of WLL system and is confirmed that it meets all functional and performance requirements.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.10
• /
• pp.79-85
• /
• 2009

The design of a 3.2 Gb/s serial link receiver in $0.18{\mu}m$ CMOS process is presented. The major factors limiting the performance of high-speed links are transmission channel bandwidth, timing uncertainty. The design uses a multi-level signaling(4-PAM) to overcome these problems. Moreover, to increase data bit-rate and lower BER, we designed this circuit by using a current mode amplifier, Current-mode Logic(CML) sampling latches. The 4-PAM receiver achieves 3.2 Gb/s and BER is less than $1.0\;{\times}\;10^{-12}$. The $0.5\;{\times}\;0.6\;mm^2$ chip consumes 49 mA at 3.2 Gb/s from a 1.8-V supply.

• ETRI Journal
• /
• v.42 no.4
• /
• pp.480-490
• /
• 2020

More than 42 000 fires occur nationwide and cause over 2500 casualties every year. There is a lack of specialized equipment, and rescue operations are conducted with a minimal number of apparatuses. Through-the-wall radars (TTWRs) can improve the rescue efficiency, particularly under limited visibility due to smoke, walls, and collapsed debris. To overcome detection challenges and maintain a small-form factor, a TTWR system-on-chip (SoC) and its architecture have been proposed. Additive reception based on coherent clocks and reconfigurability can fulfill the TTWR demands. A clock-based single-chip infrared radar transceiver with embedded control logic is implemented using a 130-nm complementary metal oxide semiconductor. Clock signals drive the radar operation. Signal-to-noise ratio enhancements are achieved using the repetitive coherent clock schemes. The hand-held prototype radar that uses the TTWR SoC operates in real time, allowing seamless data capture, processing, and display of the target information. The prototype is tested under various pseudo-disaster conditions. The test standards and methods, developed along with the system, are also presented.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.2
• /
• pp.83-91
• /
• 2012

An RF energy detector for spectrum sensing in TV white space transceiver is presented. It is based on an RF active filtering technique that comprises a low-noise amplifier with a frequency-translation high-pass filtering feedfoward loop, which attenuates the unwanted sideband energy and only passes the wanted band energy. Unlike the conventional architecture, a new architecture that can attenuate both sidebands at the same time is proposed. A simplified system modeling method is presented to assess the non-ideality effects on the RF energy detector performances. System behavioral simulations demonstrate that the proposed architecture can be instrumental for realizaing a RF energy detector circuit in CMOS.

• ETRI Journal
• /
• v.38 no.1
• /
• pp.9-17
• /
• 2016

We demonstrate a time- and wavelength-division multiplexed passive optical network system employing a vertical-cavity surface-emitting laser array-based optical line terminal transceiver and a tunable bidirectional optical subassembly-based optical network terminal transceiver. A packet error-free operation is achieved after a 40 km single-mode fiber bidirectional transmission. We also discuss an arrayed waveguide grating, a photo detector array based on complementary metal-oxide-semiconductor photonics technologies, and low-cost key devices for deployment in access networks.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.5
• /
• pp.261-269
• /
• 2016

A high-performance transmit/receive (T/R) switch is essential for every radio-frequency (RF) device. This paper proposes a T/R switch that is designed in the CEDEC 0.13 μm complementary metal-oxide-semiconductor (CMOS) technology for 2.4 GHz ISM-band RF applications. The switch exhibits a 1 dB insertion loss, a 28.6 dB isolation, and a 35.8 dBm power-handling capacity in the transmit mode; meanwhile, for the 1.8 V/0 V control voltages, a 1.1 dB insertion loss and a 19.4 dB isolation were exhibited with an extremely-low power dissipation of 377.14 μW in the receive mode. Besides, the variations of the insertion loss and the isolation of the switch for a temperature change from - 25℃ to 125℃ are 0.019 dB and 0.095 dB, respectively. To obtain a lucrative performance, an active inductor-based resonant circuit, body floating, a transistor W/L optimization, and an isolated CMOS structure were adopted for the switch design. Further, due to the avoidance of bulky inductors and capacitors, a very small chip size of 0.0207 mm² that is the lowest-ever reported chip area for this frequency band was achieved.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.1
• /
• pp.126-142
• /
• 2016

This paper presents a wide-frequency-range, low-power transceiver with an automatic impedance-matching calibration for TV-white-space (TVWS) application. The wide-range automatic impedance matching calibration (AIMC) is proposed for the Drive Amplifier (DA) and LNA. The optimal $S_{22}$ and $S_{11}$ matching capacitances are selected in the DA and LNA, respectively. Also, the Single Pole Double Throw (SPDT) switch is integrated to share the antenna and matching network between the transmitter and receiver, thereby minimizing the systemic cost. An N-path filter is proposed to reject the large interferers in the TVWS frequency band. The current-driven mixer with a 25% duty LO generator is designed to achieve the high-gain and low-noise figures; also, the frequency synthesizer is designed to generate the wide-range LO signals, and it is used to implement the FSK modulation with a programmable loop bandwidth for multi-rate communication. The TVWS transceiver is implemented in $0.13{\mu}m$, 1-poly, 6-metal CMOS technology. The die area of the transceiver is $4mm{\times}3mm$. The power consumption levels of the transmitter and receiver are 64.35 mW and 39.8 mW, respectively, when the output-power level of the transmitter is +10 dBm at a supply voltage of 3.3 V. The phase noise of the PLL output at Band 2 is -128.3 dBc/Hz with a 1 MHz offset.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.238-246
• /
• 2011

A 3-5 GHz UWB radar chip in 0.13 ${\mu}m$ CMOS process is presented in this paper. The UWB radar transceiver for surveillance and biometric applications adopts the equivalent time sampling architecture and 4-channel time interleaved samplers to relax the impractical sampling frequency and enhance the overall scanning time. The RF front end (RFFE) includes the wideband LNA and 4-way RF power splitter, and the analog signal processing part consists of the high speed track & hold (T&H) / sample & hold (S&H) and integrator. The interleaved timing clocks are generated using a delay locked loop. The UWB transmitter employs the digitally synthesized topology. The measured NF of RFFE is 9.5 dB in 3-5 GHz. And DLL timing resolution is 50 ps. The measured spectrum of UWB transmitter shows the center frequency within 3-5 GHz satisfying the FCC spectrum mask. The power consumption of receiver and transmitter are 106.5 mW and 57 mW at 1.5 V supply, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.906-909
• /
• 2006

This paper proposes a new body-effect compensated switch configuration for low voltage and low distortion switched-capacitor (SC) applications. The proposed circuit allows rail-to-rail switching operation for low voltage SC circuits and has better total harmonic distortion than the conventional bootstrapped circuit by 19 dB. A 2-1 cascaded sigma-delta modulator is provided for performing the high-resolution analog-to-digital conversion on audio codec in a communication transceiver. An experimental prototype for a single-stage folded-cascode operational amplifier (opamp) and a 2-1 cascaded sigma-delta modulator has been implemented in a 0.25 micron double-poly, triple-metal standard CMOS process with 2.7 V of supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.7
• /
• pp.440-448
• /
• 2014

A $4{\times}10$ Gb/s Transimpedance Amplifier (TIA) array is implemented in $0.13{\mu}m$ CMOS process technology, which will be used in the receiver of TWDM-PON system. A technology for bandwidth enhancement of a given $4{\times}10$ Gb/s TIA presented under inductor peaking technology and a single 1.2V power supply based low voltage design technology. It achieves 3 dB bandwidth of 7 GHz in the presence of a 0.5 pF photodiode capacitance. The trans-resistance gain is $50dB{\Omega}$, while 48 mW/ 1channel from a 1.2 V supply. The input sensitivity of the TIA is -27 dBm. The chip size is $1.9mm{\times}2.2mm$.