• 한국표면공학회지
• /
• 제52권2호
• /
• pp.62-71
• /
• 2019

Al1050 and Al7075 alloy specimens were exposed to atmospheric conditions for 24 months and analyzed by Transmission Electron Microscopy to characterize their corrosion behavior and oxide film characteristics, especially focusing on intergranular corrosion or oxidation. In general, the intergranular oxygen penetration depth of Al1050 was deeper than Al7075. Since O and Si signals were overlapped at the oxidized grain boundaries of Al1050 and Mg is not included in Al1050, it is concluded that Si segregated along the grain boundaries directly impacts on the intergranular corrosion of Al1050. Cr-Si or Mg-Si intermetallic particles were not observed along the grain boundaries of Al7050, but Mg-Si particle was barely observed in the matrix. 10-nm size Mg-Zn particles were also found all over the matrix. Mg was mainly observed along the oxidized grain boundary of Al7075, but Si was not detected due to the Mg-Si particle formation in the matrix and relatively low concentration of Si in Al7075. Therefore, it is thought that Mg plays an important role in the intergranular corrosion of Al7075 under atmospheric corrosion conditions.

• 한국주조공학회지
• /
• 제10권1호
• /
• pp.43-49
• /
• 1990

The influences of Cu and Mg addition on wear properties of SiC particulate reinforced Al-Si metal(alloy) matrix composites were investigated. Metal matrix composites were prepared by combination of compocasting and hot pressing techniques. The main results obtained are as follows : 1) The composite with Mg addition exhibits letter wear resistance than that with Cu addition. It is considered that Mg addition improved wettability of matal matrix composite by the strong segregation to the SiC / Al matrix interface. 2) After homogenization treatment, it was found that the interfacial segregation of Mg was predominant, while that of Cu was not detected. 3) The SiC / Al-11Si eutectic composite exhibits better wear resistance than the SiC / Al-6Si hypoeutectic composite does. 4) It seems that the increase in the amount of Mg addition affects on the uniform dispersion of SiC particulates, on the refinement of microstructure and on age hardening and these effects cause wear resistance improvement of composites.

• 한국재료학회지
• /
• 제30권3호
• /
• pp.111-116
• /
• 2020

Two different casting speeds of 60 and 80mm/min are adopted to determine the effect of casting speed on the microstructure and mechanical properties of Al-Mg-Si/Al hybrid material prepared by duo-casting. The obtained hybrid material has a uniform and straight macro-interface between the pure Al side and the Al-Mg-Si alloy side at both casting speeds. When the casting speed is increased to 80mm/min, the size of primary α phases in Al-Mg-Si alloy decreases, without change of shape. Although the Al-Mg-Si alloy produced at higher casting speed of 80mm/min shows much higher ultimate tensile strength (UTS) and 0.2 % proof stress and lower elongation, along with higher bending strength compared to the case of the 60mm/min in casting speed, the tensile properties and bending strength of the hybrid material, which are similar to those of pure Al, are the same regardless of the increase of casting speed. Despite the different casting speeds, deformation and fracturing in hybrid materials are observed only on the pure Al side. This indicates that the macro-interface is well-bonded, allowing it to endure tensile and bending deformation in all hybrid materials.

• 한국주조공학회지
• /
• 제43권6호
• /
• pp.286-293
• /
• 2023

본 연구에서는 고강도 Al-Mg-Zn계 알루미늄 합금 연속주조 빌렛의 균질화처리 과정 중 미세조직 전개과정을 다양한 장비(OM, SEM, EDS, DSC)로 분석 및 고찰하였다. 우선, 연속주조된 알루미늄 합금 빌렛 내 입계 및 입내에는 AlMgZn, AlMgFe 및 AlMgZnSi상 등 많은 양이 불균일하게 존재하며, 이들 상은 균질화처리 과정 중 입계 및 기지로 용해된다. 합금설계 프로그램 및 동력학 방정식을 활용한 결정립 내 주요 합금원소인 Mg 및 Zn의 확산거동을 분석한 결과, JMatPro 내 균질화처리 모드에서 대상합금 내 Mg이 Zn 대비 기지 내로 빠르게 용해되나, 동력학 방정식의 경우에도 유사한 경향성이 나타난다. 확산속도에 대한 의미로 실제로 Zn 대비 상대적으로 Mg이 많은 양을 함유하고 있어 기지로 확산과 동시에 고용되었음을 확인할 수 있었다.

• 한국분말재료학회지
• /
• 제30권6호
• /
• pp.470-477
• /
• 2023

The effects of annealing on the microstructure and mechanical properties of Al-Zn-Mg-Cu-Si alloys fabricated by high-energy ball milling (HEBM) and spark plasma sintering (SPS) were investigated. The HEBM-free sintered alloy primarily contained Mg₂Si, Q-AlCuMgSi, and Si phases. Meanwhile, the HEBM-sintered alloy contains Mg-free Si and θ-Al₂Cu phases due to the formation of MgO, which causes Mg depletion in the Al matrix. Annealing without and with HEBM at 500℃ causes partial dissolution and coarsening of the Q-AlCuMgSi and Mg₂Si phases in the alloy and dissolution of the θ-Al₂Cu phase in the alloy, respectively. In both alloys, a thermally stable α-AlFeSi phase was formed after long-term heat treatment. The grain size of the sintered alloys with and without HEBM increased from 0.5 to 1.0 ㎛ and from 2.9 to 6.3 ㎛, respectively. The hardness of the sintered alloy increases after annealing for 1 h but decreases significantly after 24 h of annealing. Extending the annealing time to 168 h improved the hardness of the alloy without HEBM but had little effect on the alloy with HEBM. The relationship between the microstructural factors and the hardness of the sintered and annealed alloys is discussed.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.29-33
• /
• 2014

The electrochemical characteristics of Al-Si casting alloys (Al-10%Si, Al-9%Si, Al-7%Si) in 3.5% NaCl solution at room temperature was studied using potentiodynamic techniques. The electrochemical values of corrosion potential($E_c$), corrosion current density($I_c$) and corrosion rate(mpy) were examined. The Al-Si alloys had several compounds such as $Mg_2Si$, ${\pi}$-$Al_8Si_6Mg_2Fe$ and $Al_2CuMg$ which could affect corrosion resistance significantly. The potentiodynamic polarization curve exhibited typical active behavior in anodic polarization curve. The major corrosion mechansim for the Al-Si alloys were pitting and grain boundary corrosion. As increasing Si and Cu contents, their corrosion resistance was decreased.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1241-1248
• /
• 2018

The reactive wetting behaviors of molten Zn-Al-Mg alloys on MnO- and amorphous (a-) $SiO_2$-covered steel sheets were investigated by the sessile drop method, as a function of the Al and Mg contents in the alloys. The sessile drop tests were carried out at $460^{\circ}C$ and the variation in the contact angles (${\theta}_c$) of alloys containing 0.2-2.5 wt% Al and 0-3.0 wt% Mg was monitored for 20 s. For all the alloys, the MnO-covered steel substrate exhibited reactive wetting whereas the $a-SiO_2$-covered steel exhibited nonreactive, nonwetting (${\theta}_c>90^{\circ}$) behavior. The MnO layer was rapidly removed by Al and Mg contained in the alloys. The wetting of the MnO-covered steel sheet significantly improved upon increasing the Mg content but decreased upon increasing the Al content, indicating that the surface tension of the alloy droplet is the main factor controlling its wettability. Although the reactions of Al and Mg in molten alloys with the $a-SiO_2$ layer were found to be sluggish, the wettability of Zn-Al-Mg alloys on the $a-SiO_2$ layer improved upon increasing the Al and Mg contents. These results suggest that the wetting of advanced high-strength steel sheets, the surface oxide layer of which consists of a mixture of MnO and $SiO_2$, with Zn-Al-Mg alloys could be most effectively improved by increasing the Mg content of the alloys.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2013년도 춘계학술대회 논문집
• /
• pp.112-113
• /
• 2013

Thin CrAlMgSiN films, whose composition were 30.6Cr-11.1Al-7.3Mg-1.2Si-49.8N (at.%), were deposited on steel substrates in a cathodic arc plasma deposition system. They consisted of alternating crystalline Cr-N and AlMgSiN nanolayers. After oxidation at $800^{\circ}C$ for 200 h in air, a thin oxide layer formed by outward diffusion of Cr, Mg, Al, Fe, and N, and inward diffusion of O ions. Silicon ions were relatively immobile at $800^{\circ}C$. After oxidation at $900^{\circ}C$ for 10 h in air, a thin $Cr_2O_3$ layer containing dissolved ions of Al, Mg, Si, and Fe formed. Silicon ions became mobile at $900^{\circ}C$. After oxidation at $900^{\circ}C$ for 50 h in air, a thin $SiO_2-rich$ layer formed underneath the thin $Cr_2O_3$ layer. The film displayed good oxidation resistance. The main factor that decreased the oxidation resistance of the film was the outward diffusion and subsequent oxidation of Fe at the sample surface, particularly along the coated sample edge.

• 한국주조공학회지
• /
• 제30권2호
• /
• pp.76-82
• /
• 2010

Effect of reaction time and sludge formation on the thickness of die soldering reaction layer has been studied in Al-9Si-0.3Mg casting alloy. Ternary ${\alpha}_{bcc}-Al_8Fe_2Si$ and ${\alpha}_{hcp}-Al_8Fe_2Si$ intermetallic compounds formed at the interface of SKD61 tool steel by interaction diffusion of Al, Fe and Si atoms after 0.5hr and 6hr immersion time, respectively. Binary ${\eta}-Fe_2Al_5$ additionally formed at the interface of SKD61 tool steel after 10hr immersion time. Thickness of soldering reaction layer in die surface increased as immersion time increased from 0.5hr to 24hr. Sludge formation was ascertained in the samples which were immersed in the melts more than 10hr. Reaction of die soldering after sludge formation was more accelerated than that of before sludge formation due to a decrease in Fe content, followed by higher diffusion rate of Al in the melt by sludge formation.

• 한국주조공학회지
• /
• 제42권6호
• /
• pp.337-346
• /
• 2022

본 연구에서는 Al-7Si-(0.3~0.5)Mg-(0~0.5)Cu 합금의 용체화 처리 조건 최적화를 위해 545℃ 온도 조건에서 최대 7시간까지 용체화 처리를 수행한 후 광학현미경 및 FE-SEM을 활용한 미세조직 관찰 및 브리넬 경도 측정을 수행하였다. 합금 내 공정 Si 상은 용체화 처리 초반 3시간 동안 급격한 조대화 현상을 나타내었으며, 이후에는 용체화 처리가 진행되어도 Si 상 크기는 크게 변화하지 않았다. 한편 공정 Si 상의 구상화의 경우, 용체화 처리 시간이 7시간에 도달할 때 까지 지속적으로 진행되었다. Cu가 첨가된 합금의 주방상태에서는 Q-Al₅Cu₂Mg₈Si₆ 상과 θ-Al₂Cu 상이 확인되었으나, 545℃에서 3시간 동안 진행된 용체화 처리 이후에는 모두 분해되었다. 주방상태에서 확인된 π-Al₈FeMg₃Si 상은 5시간의 용체화 처리 이후에 사라지거나(0.3wt%Mg) 혹은 7시간의 용체화 처리 이후에도 존재(0.5wt%Mg)하였다. 초정 α상 내 Mg 및 Cu 함량은 용체화 처리 시간이 5시간에 도달할 때 까지 증가하였으며, 이는 Mg 및 Cu를 함유한 금속간 화합물의 용체화 시간에 따른 분해 거동과 일치하였다. Al-7Si-Mg-Cu 합금의 용체화 처리 과정에서 확인한 미세조직 변화를 종합적으로 고려할 때, 본 연구에서 다룬 합금의 석출강화 효과 극대화를 위해서는 545℃ 조건에서 최소 5시간의 용체화 처리가 필요한 것으로 판단되며, 용체화 처리 조건 별로 측정된 브리넬 경도 데이터로부터 동일한 최적 용체화 처리 조건을 도출할 수 있었다.