• Journal of Adhesion and Interface
• /
• v.20 no.4
• /
• pp.146-154
• /
• 2019

In this study, alkoxysilane-functionalized amphiphilic polymer (AFAP), which have hydrophilic segment and hydrophobic segment functionalized by alkoxysilane group at the same backbone, was synthesized and used as a dispersant and control agent for reaction rate in the preparation of colloidally stable organic-inorganic (O-I) hybrid sols. After reaction with fluorosilane compounds, fluorinated O-I hybrid sols were prepared and coated onto glass substrate to form hydrophobic O-I hybrid coating films through low-temperature curing process. Surface hardness and hydrophobicity of cured coating films were varied with type of solvent and composition of AFAP and fluorinated alkoxysilane compounds. At appropriate solvent and composition of fluorinated alkoxysilane compounds, O-I hybrid coating film having high transparency and surface hardness could be prepared, which could be applicable to cover window of solar cell and displays.

• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.7-12
• /
• 2008

We confirmed that poly (ethylene terephthalate) (PET) fiber had the possibility to improve the mechanical properties of polypropylene (PP) by fabricating PP/PET fiber composites because PET enhanced mechanical properties and higher melting temperature than PP. But lower compatibility of between PP and PET fibers induced poor mechanical properties of PP/PET fiber composites in spite of incorporating PP-g-MAH as compatibilizer. To solve these problems of PP/PET fiber composites, we carried out a surface treatment on PET fiber using NaOH solution and Prepared PP/PET fiber composites with good mechanical properties by adding PP-g-MAH as a compatibilizer Then the behavior of the mechanical properties was correlated with the results obtained from SEM and IR spectroscopy.

• Journal of Hydrogen and New Energy
• /
• v.17 no.3
• /
• pp.347-352
• /
• 2006

분자전해질연료전지 내의 다공성 기체확산층은 반응가스의 확산과 전자이동통로의 역할을 수행할 뿐만 아니라 전기화학반응에 의해 공기극에서 생성된 수분(기상 혹은 액상)을 반응면으로부터 분리판 채널 방향으로 이동시켜 배출시키는 중요한 역할을 한다. 따라서 물관리를 통한 성능향상을 위해서는 기체 확산층의 구조 및 재료특성에 대한 심도 릴은 연구가 필요하다. 실제 단위전지 체결시 기체확산층은 분리판의 리브(rib)에 의해 눌리게 되며, 그 부분의 기공 크기 분포의 변화를 야기한다. 또한 리브 전단부분에서 탄소 섬유가 손상을 입으며, 탄소 섬유를 감싸고 있는 PTFE coating이 벗겨지게 되어 표면화학적 특성이 달라진다. 본 연구에서는 단위전지 체결 시 분리판에 의해 눌리는 기체확산층의 기공 크기 분포 변화를 측정하였으며, 기공의 소수성에서 친수성으로의 변화를 알아보았다. Mercury 기공 측정기와 PMI 기공 측정기는 큰 기공 분포의 변화에, 질소의 흡/탈착을 이용한 BET 방식은 작은 크기의 기공 분포 변화 관찰에 사용되었다. 체결압에 의한 탄소섬유의 구조적 변화와 아울러 표면의 습윤 정도의 변화를 XPS와 물/알콜 Uptake를 이용해 알아보았다. 이 연구를 바탕으로 물관리를 통한 연료전지 성능 향상을 위한 최적 GDL 선정에 기반이 되는 자료를 도출하였다.

• Membrane Journal
• /
• v.21 no.2
• /
• pp.118-126
• /
• 2011

A method of light pre-irradiation, one of methods modifying hydrophobic surface to hydrophilic surface in a membrane, was proposed to overcome the drawback of previous methods such as blending, chemical treatment and post-irradiation, Process of membrane preparation in the study was comprised of 4 parts as follows: firstly process of precursor preparation to introduce hydrophilic nature under atmosphere and aqueous vapor by irradiating electron beam (EB), secondly process of dope solution preparation to cast on non-woven fabrics, thirdly process of casting to prepare membrane and finally process of coagulation in non-solvent to form porous structure. The merit of this method might show simple process as well as homogenous modification compared to previous methods. To carry it out, precursor was prepared by irradiating EB to powder PVDF at 75~125 K Gray dose. Precursor prepared was analyzed by FTIR, EDS and DSC to confirm the introduction of hydrophilic function and its mechanism. From their results, it was inferred I conformed that hydrophilic function was hydroxy1 and it was introduced by dehydrozenation. Hydrophilicity of membranes prepared was evaluated by contact angle (pristine PVDF : $62^{\circ}$, 125 K Gray-PVDF$13^{\circ}$). Porosity was evaluated by mercury intrusion method, simultaneously morpholoy and surface pore size were observed by SEM phothographs. The result showed the trend that more dose of EB led to smaller pore size and to lower porosity (pristine PVDF : 82%, 125 K Gray-PVDF : 63%). Trend of water permeability was similar to result above (pristine PVDF : 892 LMH, 125 K Gray-PVDF : 355 LMH).

• Applied Chemistry for Engineering
• /
• v.17 no.4
• /
• pp.403-408
• /
• 2006

To enhance the dental properties of polymeric dental restorative composite activated by visible-light, the surface of hydrophilic silica nanoparticle was hydrophobically treated using $\gamma$-methacryloxypropyltrimethoxysilane ($\gamma$-MPS) coupling agent. Structural properties and dispersity of silica in the composite was compared with the hydrophobicity of silica. Polymerization characteristic of the composite was also evaluated. Degree of hydrophobicity of silica nanoparticle was considerably improved with an increase of $\gamma$-MPS upto 40 wt% and converged asymptotically. Additionally, with an increase of the hydrophobicity of silica nanoparticle, the dispersity of silica was improved and the residual monomer in the composite was not detected from nuclear magnetic resonance experiment which indicated superior polymerization behavior.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.639-645
• /
• 2008

The objectives of this research are to (1) observe changes in particle size distribution due to formation of microflocs during coagulation process (2) identify the membrane fouling potential on cross flow system (3) investigate the mechanism of membrane fouling. The rate of flux decline for the hydrophobic membrane was significantly greater than for the hydrophilic membrane, regardless of pretreatment conditions. The pretreatment of the raw water significantly reduced the fouling of the UF membrane. Also, the rate of flux decline for the hydrophobic membrane was considerably greater than for the hydrophilic membrane. Applying coagulation process before membrane filtration showed not only reducing membrane fouling, but also improving the removal of dissolved organic materials that might otherwise not be removed by the membrane. That is, during the mixing period, substantial changes in particle size distribution occurred under rapid and slow mixing condition due to the simultaneous formation of microflocs and NOM precipitates. Therefore, combined pretreatment using coagulation not only improved dissolved organics removal efficiency but also flux recovery efficiency.

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.23-36
• /
• 2008

Polymer-clay nanocomposites, a novel organic-inorganic hybrid, attract much attention from both scientific fields and engineering fields due to their balanced improvements in mechanical properties as well as diffusion behaviors, including flame-retarding and barrier properties, with small amounts of clay. Preparation of polymer-clay nanocomposites, summarized as a process for uniform dispersion of hydrophilic layered clays in hydrophobic polymer matrixes, includes several technologies and scientific phenomena, such as surface-modifications of clay layers, physical properties of clays in liquids and dried states, polymer synthesis, polymer rheology, behaviors of polymer solutions/or monomers in the confined geometry, mechanical properties of polymers and clays. To comprehend complicated physical/chemical phenomena involved in the fabrication of nanocomposites, we reviewed physical properties of clays, structures of clays in nanocomposites, characterization of nanocomposites, the relation between morphology and physical property of nanocomposites, surveyed recent research trends, and then suggested a few strategies or methods for fabrication of nanocomposites reflecting future research directions.

• Journal of Conservation Science
• /
• v.11 no.1 s.14
• /
• pp.38-51
• /
• 2002

The first priority we face in the conservation of wall paintings, is the conservation of painting layer. The 'painting layer' is sometimes called the pigment layer, and refers to the painted surface. For the consolidation of this painting layer we use 'fixative'. Fixative is a common adhesive which has been used in various field and conservators have made up for the weak points in the consolidation of wall paintings. In my thesis, I will summarise the range of use, standards of selection, and results of research on the use of fixative in the conservation of European paintings. In addition, I will describe various kinds of our traditional fixatives. As synthetic resins have proved that it is not ideal as a fixative for wall painting, conservators have studied to find an alternative. Same as European conservators, Asian scientists has researched to find alternative fixative which is more suitable to the wall paintings in Asia based on their traditional techniques and materials. Therefore, 1 have studied to find an adequate fixative for our own wall paintings and I could conclude that we can consider traditional fixative which is made of 'seaweeds' as an alternative and it is very important to proceed research and experiment on this material.

• Membrane Journal
• /
• v.31 no.6
• /
• pp.393-403
• /
• 2021

Enzymes are important class of catalyst for biotransformation. Stability and reusability of enzymes during the catalysis process is a key issue. Activity of enzyme can be enhanced by its immobilization on a suitable substrate by creation of specific microenvironment. A variety of membranes has been used as substrate due to the biocompatibility and simpler method to tune hydrophilicity/hydrophobicity property of the membrane surface. In this review, polymer membranes including cellulose, polyacrylonitrile (PAN), polydimethylsiloxane (PDMS), polyvinylidene fluoride (PVDF), polyethersulfone (PES) are introduced and discussed in detail. Biodegradation of organic contaminants by immobilized enzyme is an environmental friendly process to reduce the contamination of environment in pharmaceutical company and textile industries. The controlled hydrolysis of oil can be performed in enzyme immobilized membrane bioreactor (EMBR), resulting in reducing carbon emission and reduced environmental pollution. Bioethanol and biodiesel are considered alternative fossil fuels that can be prepared in EMBR.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1721-1725
• /
• 2010

This paper reports the fabrication of geometry-controlled carbon microneedles by a backside exposure method and pyrolysis. The SU-8 microneedles are a polymer precursor in a carbonization process, which geometries such as base diameter, spacing, and aspect ratio can be controlled in a photolithography step. Using this fabrication method, highly reproducible carbon microneedles, which have high aspect ratios of more than 10 and very sharp nanotips, can be realized. The quartz surface with carbon microneedles becomes very hydrophilic and its wettability is adjusted by carrying out the silane treatment. In the carbon microneedle array ($3\;{\mu}m{\times}3\;{\mu}m$), the contact angle is extremly enhanced (${\sim}180^{\circ}$); this will be advantageous in developing low-drag microfluidics and labs-on-a-chip as well as in other bio-applications.