• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1246-1253
• /
• 2009

This paper presents derived a calculating form of fuzzy inference, based on decomposition of $\alpha$-level sets. Based on the calculating form it is propose that fuzzy logic circuits of PI+PD controller are a body from fuzzy inference to defuzzificaion in cases where the command variable u directly is generated PWM. The effect of quantization on $\alpha$-levels is investigated. with input/out characteristics of fuzzy controller by simulation. It is concluded that 4 quantization levels are sufficient result for fuzzy control performance of DC servo system. Simulation and experimental results demonstrated that the hardware implementation of the proposed controller can successfully provide good performance on the position control of DC servo system.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.129-136
• /
• 2007

In this paper, a simple but effective Dataline Redundancy Circuit (DRC) is proposed for a dual-port 1T-SRAM embedded in Display ICs. The DRC designed in the dual-port $320{\times}120{\times}18$-bit 1T-SRAM is verified in a 0.18-um CMOS 1T-SRAM process. In the DRC, because its control logic circuit can be implemented by a simple Shift Logic Circuit (SLC) with only an inverter and a NAND that is much simpler than the conventional, it can be placed in a pitch as narrow as a bit line pair. Moreover, an improved version of the SLC is also proposed to reduce its worst-case delay from 12.3ns to 5.9ns by 52%. By doing so, the timing overhead of the DRC can be hidden under the row cycle time because switching of the datalines can be done between the times of the word line setup and the sense amplifier setup. The area overhead of the DRC is estimated about 7.6% in this paper.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.652-654
• /
• 2016

This paper shows the Design and implementation of sinusoidal BLDC motor drive logic using SVPWM method with FPGA. Sinusoidal BLDC motor driver logic consists of sine-wave PWM generator, dead-time and lead angle control logic. PWM generator logic is designed using SVPWM method for increase of 15.5% linear domain than general sine-wave PWM. This logic is verified and implemented using Spartan-6 FPGA Board. Test results show that THD(Total Harmonic Distortion) of motor-driving current is 19.2% and rotor position resolution is 1.6 degree.

• Journal of Drive and Control
• /
• v.13 no.2
• /
• pp.51-58
• /
• 2016

The present study deals with the issue of clamping force control of an injection molding machine using 2-way cartridge valve based logic circuit. The operating principle for the cartridge valve is described with its construction and static opening behavior. Basic module circuits are designed first and analysed according to the basic functions. Then they are combined with a virtual design model for the clamping mechanism to simulate the control performance of the overall system. The backlash inherent in the mechanism is considered while evaluating the time-delay in the process of clamping force build-up. The effects of a couple of design parameters in backlash, i.e., interval and stiffness have been demonstrated in the time-domain.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.917-925
• /
• 2016

Schmitt Trigger logic is a gate level design method to have hysteresis characteristics to improve noise immunity in digital circuits. Dynamic Threshold voltage MOS(DTMOS) Schmitt trigger circuits can improve noise immunity without adding additional transistors but by controlling substrate bias. The performance of DTMOS Schmitt trigger logic has not been verified yet in standard CMOS process through measurement. In this paper, DTMOS Schmitt trigger logic was implemented and verified using Magna $0.18{\mu}m$ MPW process. DTMOS Schmitt trigger buffer, inverter, NAND, NOR and simple digital logic circuits were made for our verification. Hysteresis characteristics, power consumption, and delay were measured and compared with common CMOS logic gates. EM Immunity enhancement was verified through Direct Power Injection(DPI) noise immunity test method. DTMOS Schmitt trigger logics fabricated using CMOS process showed a significantly improved EM Immunity in 10 M~1 GHz frequency range.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.403-410
• /
• 2005

This Paper Presents development of solar may shunt switching unit with a fully regulated Power regulation for Geostationary Earth Orbit(GEO) satellite. This shunt switching unit comprises the solar may shunt modules that regulate the solar array power. These solar array shunt modules connect/disconnect the solar array segments to/from the bus through switching actions. And that is also possible simply extension to an existing design by FPGA control logic changing. In order to verify the proposed design, the control logic and worst case analysis are analyzed and the simulation and experimental results we shown.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.4
• /
• pp.42-48
• /
• 2014

In this paper, we propose a new small swing domino logic that reduces the swing amplitude by using twist-connected PMOS and NMOS transistors. The output swing range of the proposed circuit is adjusted by the size of the twist-connected transistors and the load capacitance. The designed RCA with the proposed circuit technique shows reduction of the power consumption by 37% and PDP performance by 43% compared with the domino CMOS logic.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.6
• /
• pp.17-25
• /
• 2004

In this paper, we propose a new small swing domino logic for low-power consumption. To reduce the power consumption, both the precharge node and the output node swing the range from 0 to $V_{REF}$- $V_{THN}$, where $V_{REF}$=VDD-n $V_{THN}$ (n=1, 2, and 3). This can be done by adding the inverter structure on domino logic that allows a full swing or a small swing on its input terminal without leakage current. Compared to previous works, the proposed structure can save the power consumption of more than 30% for n=0, 1, 2, and 3 in the equation of $V_{REF}$=VDD-n $V_{THN}$. A multiplier applying the proposed domino logic has been designed and fabricated using a 0.35-${\mu}{\textrm}{m}$ n-well CMOS process under 3.3-V supply voltage. Compared with other previous works, it shows a 30% power reduction and a better feature in power-delay product.lay product.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.4
• /
• pp.798-804
• /
• 2003

In this paper, We have designed an advanced circuits for controlling the Ink Nozzle of Printer Head We can fully increase the number of nozzle by reducing the number of Input/Output PADs using the proposed new circuit. The proposed circuit is tested with only 20 nozzles to evaluate functional test using FPGA sample chip. The new circuit architecture can be estimated. Full circuit for controlling 320 nozzles was designed and simulated from ASIC full custom methodology, then the circuit was fabricated by applying 3${\mu}{\textrm}{m}$ CMOS process design rule.

• The Journal of the Korea Contents Association
• /
• v.18 no.1
• /
• pp.10-18
• /
• 2018

This paper presents a method to resynthesize logic of a programmed FPGA from a bitstream file that is a downloaded file for Xilinx FPGA (Field Programmable Gate Array). It focuses on reconfiguring the LUT (Look Up Table) logic. The bitstream data is compared and analyzed considering various situations and various input variables such as composing other logics using the same netlist or synthesizing the same logic at various positions to find a structure of the bitstream. Based on the analyzed bitstream, we construct a truth table of the LUT by implementing various logic for one LUT. The proposed algorithm extracts the logic of the LUT based on the truth table of the generated LUT and the bitstream. The algorithm determines the input and output pins used to implement the logic in the LUT. As a result, we extract a gate level logic from a bitstream file for the targeted Xillinx FPGA.