Since in 1970, the length of concrete pavements(JCP, JRCP and CRCP) are growing rapidly at both of main highways and local roads. Many of them are deteriorated and old enough to be repaired or replaced. The pavement is more important than the other infrastructures and it is very difficult to go around or block the traffic during the rehabilitation. The very-early strength latex-modified concrete(VES-LMC)may offer the advantages of high-early-strength, higher flexural strength, higher bond strength, and improved durability. The VES-LMC could be used at a kind of fast track ofr early opening to the traffic after 3 hours of concrete placement. The installation of VES-LMC overlay at Jung-Boo highway was successfully done from April 28 to 29, 2005. The traffic was closed at 07:00 PM and opened to traffic at 08:30 AM. The compressive and flexural strength of VES-MC were more than 28MPa, 6.2MPa after 4 hours, respectively.

When it is raining or snowing, floating debris flows into a lake and raises its turbidity. High level of turbidity in the lake often causes eutrophication, which pollutes the water. In order to collect and present some essential information for effective management plan for water quality, we carried out our research at the watershed of Mandae-cheon located at the upstream of Soyang Lake. We examined water quality at the time of rainfall or snowfall to analyze the changes in the amount of suspend soils(SS) in the lake.

To use land more efficiently under urbanization trend, Kangwon Province often covers open channels of creeks and uses them as parking lots or roads. A covered open channel section tends to form a rectangular culvert. Therefore, a creek with covered open channels can function as a storm drain. At the time of light rainfall, there are no significant differences except water flowing pattern between a creek with a covered open channel and a creek without it. Recently, however, the frequent occurrence of heavy rainfalls limited at a small, definite area has become problematic. When the heavy rainfall causes the carrying capacity of a creek to be exceeded,the creek with covered open channel has a more serious problem than the creek without it has. Therefore, we made an interpretation of data and conducted hydraulic model experiment to come up with economical solution to this problem.

Non-point source pollution, which is found in soil, urban area, and agricultural area, is difficult to have its amount to be estimated. Moreover, it is hard to come up with a counterplan to cope with this pollutant. Hence, the watershed of Mandae-cheon located at the upstream of Soyang Lake was chosen as our site of study. We analyzed the relationship between precipitation level of each month and pollution load in the watershed by using statistical methods: measuring BOD, T-N and T-P - which are the causes of eutrophication - in the water; and analyzing the changes in water quality caused by precipitation level of nth.

From 2000 to 2004, the research was carried out at Naerin-cheon and Inbook-cheon, the upper streams of Soyang Lake, to study the relationship between precipitation and eutrophication-causing water pollutants, BOD, T-N and T-P. During the five years, the amount of flowing water was measured, and the water quantity was examined under different precipitation levels. From the observation, outflow patterns of the water pollutants and changes in the water quality factors at the time of rainfall were clarified. In addition, estimation of the unit load was made for each stream; for Naerin-cheon at the time of rainfall, we estimated BOD to be $1,112kg/km^2/year$, T-N to be $2,077kg/km^2/year$, and T-P to be $223kg/km^2/year$; for Inbook-cheon at the time of rainfall, we estimated BOD to be $1,229kg/km^2/year$, T-N to be $1,565kg/km^2/year$, and T-P to be $255kg/km^2/year$. For the time of no rainfall different estimation was made; for Naerin-cheon, we estimated BOD to be $2,403g/km^2/day$, T-N to be $5,004g/km^2/day$, and T-P to be $53g/km^2/day$; and for Inbook-cheon, we estimated BOD to be $1,550g/km^2/day$, T-N to be $2,283g/km^2/day$, and T-P to be $42g/km^2/day$.

The goal of this study is to generate a landslide potential map using GIS(Geographic Information System) based method. A simple and efficient algorithm is proposed to generate a landslide potentialities map from DEM(Digital Elevation Model) and existing maps. The categories of controlling factors for landslides, aspect of slope, soil, vegetation are defined. The weight value for landslide potentialities is calculated from AHP(Analytic Hierarchy Process) method. Slope and Slope-direction is extracted from DEM, and soil information is extracted from digital soil map. Also, vegetation information is extracted from digital vegetation map. Finally, as overlaying, landslide potentialities map is made out, and it is compared with landslide place.

This paper is the results of experimental and numerical works on analyzing the geotechnical engineering behavior and characteristics of excavated clay slope formed by the method of excavated replacement which is one of treatments in soft soil ground. For the centrifuge model tests, models of excavated clay slope were prepared by remolding the marine clayey soil sampled from the field. Tests were performed with changing the slope to investigate the behavior of them. On the other hand, numerical analyses were carried out to analyze the change of safety factor against instability of slope with time. Changes of pore water pressure, shear strength and displacement were also investigated. As results of centrifuge model tests with slopes of 1:1.5 and 1:3 using the confining body of simulating the effect of excavation, for the case of 1:1.5, slope failure occurred right after remove the confining body whereas relatively small displacements within the range of 3.2mm, implying to maintain the stability of slope, were observed for the case of 1:3 slope. From the results of numerical analyses using the software of PLAXIS to investigate the stability of slope after excavation, the minimum safety factor against slope failure was 1.28 for the case of 1:3 slope. The further researches in the future are required with considerations of build up of static pore water pressures during acceleration of centrifuge, depth of excavation influencing the behavior of the slope and permeability of the slope since excavation of the slope was not simulated well resulted from the limitations of apparatus at the stage of excavation during the centrifuge tests.

This paper is an experimental result of investigating lateral soil movements at piled bridge abutments by using the centrifuge model facility. Three different centrifuge model experiments, changing the methods of ground improvement at bridge abutment on the soft clayey soil (no improvement, preconsolidation and plastic board drains (PBD), sand compaction pile (SCP) + PBD), were carried out to figure out which method is the most appropriate for resisting against the lateral soil movements. In the centrifuge modelling, construction process in field was reconstructed as close as possible. Displacements of abutment model, ground movement, vertical earth pressure, cone resistance after soil improvement and distribution of water content were monitored during and after centrifuge model tests. As results of centrifuge model experiments, preconsolidation method with PBD was found to be the most effective against the lateral soil movement by analyzing results about displacements of abutment model, ground movement and cone resistance. Increase of shear strength by preconsolidation method resulted in increasing the resistance against lateral soil movement effectively although SCP could mobilize the resistance against lateral soil movement. It was also found that installment with PBD beneath the backfill of bridge abutment induced effective drainage of excess pore water pressure during the consolidation by embanking at the back of the abutment and resulted in increasing the shear strength of clay soil foundation and eventually increasing the resistance of lateral soil movement against piles of bridge abutment.

Durability of concrete structures is seriously compromised by cracking at early-age concretes, particularly in high-strength or high-performance concrete structures. Since early-age cracking is influenced by various factors that affect the hydration process, early-age shrinkage and stress/strain development, the behavior at early-age is highly complex and no rational methodologies for its control have yet been established. Concrete structures often present volumetrical changes particularly due to thermal and moisture related shrinkages. Volumetric instability is detrimental to the performance and durability of concrete structures because structural elements are usually restrained. These restrained shrinkages develope tensile stresses which often results in cracking in combination with the low fracture resistance of concrete. Early-age defects in high-performance concrete due to thermal and autogenous deformation shorten the life cycle of concrete structures. Thus, it is necessary to examine the behavior of early-age concrete at the stages of design and construction. The purpose of this study was to propose a shrinkage models of VES-LMC (very-early strength latex-modified concrete) at early-age considering thermal deformation and autogenous shrinkage.

This project addresses the product identification and design application of corrugated products for kinetic architectural applications. Initially, an architectural approach to product identification was carried out with the end goal of demonstrating application design principles of numerous novel architectural examples from the forest products industry. A design and prototyping stage followed demonstrating such application design principles and functional analysis on various novel architectural examples. The results of coupling product identification with proven application advantages will be of potential value not only to architecture but also to other designers in the arts and sciences. The general motivation for the research arises out of a growing interest corrugated and paper products to be ideally suited for various architectural applications for their unparallel environmental benefits. Applications in architecture that use fewer resources and that adapt efficiently to complex and changing conditions are particularly relevant for an industry (architecture) that is increasingly aware of its environmental responsibilities. Corrugated and paper products are highly under-utilized by the building industry as design choice material for both interior and exterior applications. An increased awareness of the benefits of corrugated and paper products coupled with a process of designing for the total use and reuse will prove to be a valuable means by which issues of energy efficiency and environmental quality of buildings could be enhanced to be more efficient, affordable, and therefore reach a broader audience of users.

Application of proper orthogonal decomposition (POD) and continuous wavelet transform (CWT) is introduced to study wind speed and building roof pressures of flow separation region. In this study, a detailed analysis of the approach wind flow, wind-induced building pressure and the relation between the two fields was carried out using the POD technique and CWT analysis. The results show potential of the application of POD and CWT in characterization of spatio-temporal and spectral properties of the approach wind and its induced dynamic pressure events. Some of findings resulting from the application of this analysis can be summarized as follows: (1) The POD first principal coordinate of the roof pressure in the separated shear layer is closely correlated with the longitudinal component of oncoming flow. (2) The CWT analysis suggests that the extreme peak pressure in the separated shear layer is due to condensed large-scale eddy motions.

The planning phase of construction project success or failure of the enterprise decision the 1st dangerous duration which occurs very there is a possibility of making with the phase which is important, of construction project in life cycle most many risk. But the risk management from planning phase well does not become accomplished is the actual condition from existing construction project. Consequently, it classifies the risk event from project initial planning phase of construction project from this study which probably is substantial risk event the possibility of accomplishing from a planning phase successfully in order to be.

Digital media was realized by two-dimensional design backup. But, digital medium decides form of architecture, and act as a design tool that can expand area of thinking. With such social change, investigate for digital architecture. And, wish to analyze design process of digital architecture and search the characteristics. Through comparison of digital and analogue, clear up that the digital world had complex and ambivalent attribute. Define digital design process as "Digital continuum" with characteristic of digital architecture and divided in 3-steps of concept - development - representation. Analyzed digital design process of Frank O, Ghery, Peter Eisenman and Greg Lynn on th assumption division. As a result, design concept is starting from three-dimensional thinking instead of existent two-dimensional thinking. And because general work of process was gone by digital media, "mass costomization" was possible. Also, it gave architect new role. Differ with former days, select various variables, should tuning and cording, and emphasize role as coordinator who must select the result. Digital is summoning very radical and epoch-making change in architecture. At center of these change, digital design process asks architect complex thinking and creative concept.

Impact seismic wave method is a method for non-destructive testing of concrete structure using of stress wave which is propagate and reflected from internal flaws within concrete structure and external surface. In this study, we performed frequency domain method using impact seismic wave test for safety diagnosis of civil engineering structure. And reflection method which is used for one-dimensional target such as tunnel lining and transmission method are compared with each other.

Micro wires manufactured by the straightening process are used in the BT(Bio-Technology), IT(Information-Technology), NT(Nano-Technology). We have developed a novel wire straightener which uses the direct heating method(DHM) for straightening the micro wire and shearing device for burr-less cutting. In this study, we confirm the tendency of micro wire after the shearing process. It is impossible to remove the burr in the shearing process. However, the embodiment of minimum burr size after the shearing process is the best in-process method. In order to minimize the burr size, we have accomplished the various experiment condition such as the U-groove, the effect of the counter punch, the shear angle, clearance.

Manufacturing methods of Nano particles can be distinguished by top-down technology as physical method and bottom-up technology as chemical synthetic method. Top-down technology is a kind of method for making microstructure as like carving after forming a macroscopic structure in advance and its typical methods are ball milling, gas condensation method and so on. Nano Particles synthesized by bottom-up method have got to do dispersing process for using them as actual nano particles because their viscosity are very strong and so easy to shape cohesive substances. Therefore, this study is about a particle separating device which separates a certain constant size of grains processed already in mill and mixer because we mostly use media agitating mill as a device of milling and dispersing and we necessarily use very slight balls as media for manufacturing nano particles in the machine. The centrifugal device has been designed for passing and separating below a certain type of grain size after final process of particles in the mill.

Voltage of radiometer is measured experimentally using the radiation apparatus in each case of iron- and copper-plates as specimen heating device. The length between radiometer and conical shield and the temperature of specimen heating device are considered as variables. The length between radiometer and conical shield controls the amount of radiation from the specimen heating device. Emissivity for both iron-and copper-plates are calculated by using Stefan-Boltzmann equation. One of results shows that emissivity for both materials increases as the length between radiometer and conical shield increases.

A target of this paper is to get some elementary experimental data on the energy harvesting using a piezoelectric material. A THUNDER series piezo material (TH7-R), which has been developed by NASA engineer is selected for this study. In order to provide a mechanical energy to the piezoelectric material, a mechanical motion vibrator and its driving electronics are designed. Using a simple PWM control, the excitation frequency of vibrating mechanical motion is varied. The generated electric power as a function of the excitation frequency is monitored and analyzed. This initial experiment shows a possible energy source using a piezoelectric material for the application to low-power consumed small electronic devices such as RFID, MEMS, and etc.

The power performance monitoring system for a small class of wind turbine is established. The wind turbine power performance characteristics are determined by measured power curve and the estimated annual energy production (AEP). The measured power curve is determined by collecting simultaneous measurements of wind speed and power output at the test site under varying wind conditions. In order to determine the power performance characteristics of the wind turbine accurately, the data are of sufficient quantity and quality shall be corrected according to defined criteria. In this study, the 6kW wind turbine made by Germany Inventus GmbH is examined.

Two methods, the bin averaging method and least square method, are often used in calibrating wind turbine test sites. The objective of this work was to determine a better method to predict the wind speed at wind turbine installing point. The calibration was done at the test site on a complex terrain located in Daegwallyeong, Korea. It was performed for two different cases based on the IEC 61400-12 power performance measurement standard. The wind speeds averaged for 10 minutes ranged between 4 m/s and 16 m/s. The wind-direction bins of each meteorological mast were 10 degrees apart, and only the bins having data measured for more than 24 hours were employed for the test site calibration. For both cases, the two methods were found to yield almost same results which estimated real wind speed very closely.

This paper presents a development of the Data Logger System to transmit the outcome of the waterlevel measuring instrument using the pressure sensor by means of the CDMA network. In or order to set up the real time monitoring the waterlevel measurement system, we have designed the waterlevel sensor, communication terminal and repeater, and data logger. Furthermore, its application for the GIS(Geographical Information System) with management sever system and software solutions have also been developed to minimize the property damages from the flood disaster which occurs every year in the river.

In this paper, we propose a new data encoding algorithm for a two-dimensional bar code system. In general, the one-dimensional bar code is just a key which can access detailed information to the host computer database. But the two-dimensional bar code is a new technology which can obtain high density information without access to the host computer database. We implemented the encoding algorithm for Data Matrix bar code which is the most widely used among the many kinds of two-dimensional bar codes in the field of marking using Digital Signal Processor (TMS320C31). The performance of the proposed algorithm is verified by comparing the imprinted symbols on the steel surfaces with the codes which are decoded by a bar code reader.

This paper presents a LTCC Balun-BPF, which is a BPF(band pass filter) with a Balun in a single LTCC chip for the direct interface with a MMIC chip having balanced inputs. The physical dimension of the designed Balun-BPF is $2.4{\times}2.0{\times}0.88mm^3$ and the used dielectric constant ${\varepsilon}_r$ is 36. A Balun of three-lines structure with striplines and a BPF of comb-line structure was combined into the Balun-BPF. The simulated result shows 4.8㏈ of insertion loss, 178~179 degree of the phase imbalance, 14㏈ of the return.

Instead of the incandescent lamps the LED lamps have been used on the traffic signal lamp with the advantages of small loss, no lens and long life. In this paper, we have compared three kinds of the LED controller structures and showed the LED array decision methods. We studied the temperature characteristics on LED and the temperature compensation network. The experimental results showed that the electrical characteristics of three kinds of the LED controller structures were different each other. We concluded that the temperature compensation is the important technique, the best compensation network has the ${\pm}10%$ variation for the luminous intensity.

In this paper we proposed the remote control system for the door lock by the unified modem with the wireless and the power line modem. We developed the management system program between the door-lock system and the proposed unified modem. The infrared communication system was used between the Door-Lock system and the power line modem. With the unified developed modem and the Door-Lock system, it is possible to control remotely the developed system in the internet service area.

The rectifier characteristics and the quality of the input current worsens with the increase of unbalances or harmonics of the supply voltages. Rectifier input current harmonics interfere with proper power system operation, reduce rectifier power factor, and limit the power available from a given source. It is of importance to select appropriately the rectifier's output filter inductance to determine the rectifier input current waveform, the input current harmonics, and the power factor. This paper presents a quantitative analysis of single and three phase rectifier input current harmonics, total harmonic distortion, and power factor as a function of the output filter inductance under balanced and unbalanced conditions. Also, its performance under the supply voltage including harmonics be investigated. These results provide a reference for selecting reasonable rectifier's output filter inductance for given harmonics or power factor criterion.

The PWM(Pulse Width Modulated) converter for the AC to DC rectification has become attractive in the industrial variable-speed drive application and the electric utilities due to the following benefits: Nearly the sinusoidal input current with unity power factor; Controllable DC link voltage; Bidirectional power flow. This paper presents a quantitative analysis of single and three phase PWM converter's input and output characteristics as a function of the input filter inductance under balanced and unbalanced conditions. Also, its performance under the supply voltage including harmonics is investigated by simulation with Matlab Simlulink and experiments. These results provide a reference for selecting the reasonable converter's input filter inductance for given harmonics or power factor criterion.

The wireless sensor network consists of a number of sensor nodes which have physical constraints. Each sensor node senses surrounding environments and sends the sensed information to Sink. The inherent vulnerability in security of the sensor nodes has promoted the needs for the lightweight security protocol. In this paper, we propose a non-hierarchical sensor network and a security protocol that is suitable for monitoring the man-made objects such as bridges. Furthermore, we present the efficient way of setting the routing path by storing IDs, MAC(message authentication code) and the location information of the nodes, and taking advantage of the two node states, Sleep and Awake. This also will result in the reduced energy consuming rate.

We present a numerical analysis of the optimal group number for minimizing the average paging delay. In the analysis, we consider uniform distributions for location probability conditions and apply M/D/1 queueing model to paging message queues of cells. We also get the lower bounds of group numbers and investigate the minimum transmission capacity under average paging delay constraints. Minimizing the average paging delay is important because it means minimizing the amount of bandwidth used for locating mobile terminals. Therefore, the numerical results of this paper will be very useful in PCS system when designing its signalling capacity due to its simplicity and effectiveness.

Dietary powder from Plantaginis ovatae testa was prepared by mechnical milling/grinding of the outer layer of the seed. The crystalline/surface structures of its powder (100 mesh) were examined, and several physical functionalities including, water capacity, oil holding capacity, emulsion/foam properties and physiological functionality such as in-vitro glucose and bile acid retarding effects were also investigated. Water holding capacity(WHC) of psyllium powder was $33.71{\pm}0.10g$ water retained/g solid at room temperature, whileas oil holding capacity(OHC) for soybean or rice bran oil were about 1.80g oil retained/g solid. These values of WHC and OHC were about 5.6 times higher and 2.8 times lower than those of commercial ${\alpha}$-cellulose, respectively. Changes of pH showed a small effect on WHC, but WHC increased with temperature. Emulsion capacity of 2%(w/v) psyllium was about 60% level of 0.5%(w/v) xanthan gum but emulsion stability after incubation of 24 hours showed about 1.4 times improvement of xanthan gum(0.5%,w/v). Also, psylliume(above 2%, w/v) alone had higher foam capacity than that of xanthan(1.1 times) and especially, 1 or 2% addition of psyllium improved the foam stability of protein solution(1% albumin+0.5% $CaCl_2$) by factor of 3.3 and 6.0 times, respectively. The glucose and bile acid retarding effects of psyllium powder were relatively very excellent suggesting the prevention from diabetes and arteriosclerosis. Especially, psyllium showed the 3.7 and 3.3 times higher effect on in-vitro glucose and bile acid retardation than those of commercial ${\alpha}$-cellulose, respectively.

Exopolysaccharide (CBP) from submerged culture broth of Ganoderma lucidum mycelium and the water soluble (BWS) and water insoluble (BWI) fractions of CBP were prepared by gel filtration. Antitumor activity and effects on proliferation and differenciation of human cancer cells and mouse NIH 3T3 cells were studied. Cytotoxicity test of CBP, BWS and BWI fractions on human cancer cell lines was performed by using sulforhodamine B (SRB) assay. A549 (lung carcinoma), Colo320 DM and HSR (colon carcinoma), and NIH 3T3 cells were used. BWI fraction showed the strongest cytotoxicity (maximum 20% survival) to all human cells tested. However it did not induced apoptosis. Interestingly BWI fraction did not exert cytotoxic effect on NIH 3T3 cells at low concentration of cells ($5{\times}10^4$) but strong toxic effect at high concentration of cells($5{\times}10^5$) which showed transformed morphology. These results suggest that BWI may have cancer cell specific anticancer activity. However, BWI fraction did not effect the amount of pRb and c-myc protein, which implied that BWI fraction did not act at the early stage of signal transduction pathway. CBP fraction induced differenciation of human leukemic cell line, HL-60 cells suggesting the carcinogenesis prevention of normal cell and possible induction of normalization for cancer cell.