Encapsulation of organic based devices is essential issue due to easy deterioration of organic material by water vapor. Thin layer of encapsulation film is required to preserve transparency yet protecting materials in it. Atomic layer deposition(ALD) is a promising solution because of its low temperature deposition and quality of the deposited film. $Al_2O_3$ or $Al_2O_3/TiO_2/Al_2O_3$ multilayer film has shown excellent environmental protection characteristics despite of thin thicknesses of the films. $Al_2O_3/TiO_2/Al_2O_3$ multilayer and 1.5 dyad layer of $Al_2O_3/polymer/Al_2O_3$ deposited by ALD was measured to have water vapor transmittance rate(WVTR) well below the detection limit($5.0{\times}10^{-5}g/m^2day$) of MOCON Aquatran 2 equipment.

Recent enhancement in the still image acquisition devices has been widely perpetrated into the daily life of the common people. Due to this trend, the voluminous still images, that are produced and shared in the personal or the massive storage, need to controlled with effective and efficient management. The human-devised or system-generated still image identifiers used for the identification of the images are at risk in the situation of unexpected changing or eliminating of the identifiers. In this paper, we propose a parallel processing based method for still image identifier generation by utilizing the still image internal features.

Lithium-ion batteries are widely used, from lightweight to energy-intensive, from small devices to large ESSs. However, it is sensitive to the surrounding environment and there is a change in performance depending on the temperature change. In this study, the temperature dependence of the charge / discharge characteristics of the battery is shown through simulation and the distribution of the salt concentration in the electrolyte is observed when the sudden temperature change is applied.

In this paper, the effect of battery-package shape of electric vehicle on the forced convection around a group of battery cells has been numerically investigated. Simulations for the two package shapes with straight/curved ducts have been conducted to examine the two design factors; the maximum temperature and the temperature deviation of a group of cells which influence the cell durability. The simulation of the conjugate heat transfer has been simplified by employing an equivalent thermal conductivity of cell that consists of various materials. It has been found that the maximum temperature and the temperature deviation of curved duct were lower than those of straight duct. Velocity fields have also been examined to describe the temperature distribution of a group of cells and the position of maximum temperature was found to be related to the dead zone of flow field.

The result of stripping process for the removal of the post etch/ash Photoresist (PR) residue on an aluminum patterned wafer by using supercritical $CO_2$ ($sc-CO_2$) mixture, was investigated by scanning of electron microscope (SEM) inspection of wafer, measuring the cloud points and visual observation of the state of $sc-CO_2$ mixtures. It was found that $sc-CO_2$ mixtures were made by mixing additives and $sc-CO_2$ should form homogeneous and transparent phase (HTP) in order to effectively and uniformly remove the post etch/ash PR residue on the aluminum patterned wafer using them. The additives were formulated by mixing and co-solvents like an amine compound and fluorosurfactants used as HTP agents, and the PR residue on the wafer were able to be rapidly and effectively removed using the $sc-CO_2$ mixture of HTP. The five kinds of additives were formulated by the recipe of mixing co-solvents and surfactants, which were able to remove PR residue on the wafer by mixing with $sc-CO_2$ at the stripping temperature range from 40 to $80^{\circ}C$. The five kinds of $sc-CO_2$ mixtures which were named as PR removers were made, which were able to form HTP within the above described stripping temperature. The cloud points of $sc-CO_2$ mixtures were measured to find correlation between them and HTP.

This paper presents a development of vision aligner with three channels for the wafer and plate bonding machine in manufacturing of LED. The developed vision aligner consists of three cameras and performs wafer alignment of rotation and translation, flipped wafer detection, and UV Tape detection on the target wafer and plate. Normally the process step of wafer bonding is not defined by standards in semiconductor's manufacturing which steps are used depends on the wafer types so, a lot of processing steps has many unexpected problems by the workers and environment of manufacturing such as the above mentioned. For the mass production, the machine operation related to production time and worker's safety so the operation process should be operated at one time with considering of unexpected problem. The developed system solved the 4 kinds of unexpected problems and it will apply on the massproduction environment.

Semiconductor is one of the most internationally competitive areas among domestic industries, the major concern of which is the stability of the wafer manufacturing processes. The first process for the manufacturing of the semiconductor wafers is the ingot growing. The vibrations are supposed to be the most important factors for the ingot quality. In order to maintain the ingot quality, the growers have the automatic shut-down equipments which are activated by vibrations, and are sensitive enough to react to the earthquakes generated in Japan. In this study, the structure of an ingot grower was analyzed through experiments and computer simulations, and further the effects of design alterations to suppress the vibrations have been investigated. The final result shows that the vibrations can be reduced substantially to improve the stability of the structure.

The effect of weak dielectric silicone dioxide($SiO_2$) embedded in polyfluorene(PFO) emitting layer of polymer-based multi structure OLED was investigated. Indium tin oxide(ITO)/poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS)/poly(9,9-di-n-octylfluorenyl-2,7-diyl)(PFO)/2,2,2"-(1,3,5-benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi)/aluminum(Al) structure OLED was fabricated by spin-coating method. Applied electric field causes some effect on $SiO_2$ in PFO layer. Thus, interaction between polymers and affected $SiO_2$ might generate electrical and luminance properties change. Experimental results, show the reduced threshold voltage of 6 V(from 23 V to 17 V). The maximum current density was rather increased from $71A/m^2$ to $610A/m^2$ and maximum brightness was also increased from $7.19cd/m^2$ to $41.03cd/m^2$, 9 and 6 times each. Additionally we obtained colour broadening result due to the increasing of blue-green band emission. Consequently we observed that electrical and luminance properties are enhanced by adding $SiO_2$ and identified the possibility of controlling the emission colour of OLED device according to colour broadening.

Poly(urethane acrylate) siloxane oligomers with Interpenetrating polymer netwoked nanoparticles were prepared to synthesize hard coating solution by reaction with diisocyanates. The diisocyanate combined siloxane hard coating solution showed more flexibility than the siloxane solution. In addition, diisocyanate resulted in improvement of curl property and surface hardness in the siloxane solution. Of the used diisocyanates, isophorone diisocyanate and acryloyloxy ethyl diisocyanate were good for UV hard coating solution. This effect will decrease brittleness in the siloxane solution using for plastic display plate.

Graphene oxide (GO)/carboxylated styrene-butadiene rubber (XSBR) nanocomposites with various contents of GO were prepared by a latex compounding method. It has been confirmed that the functional groups of GO and the hydrogen bonds between GO and XSBR are existed. It can be seen that the scorch time ($t_{s2}$), which is the measurement of incipient vulcanization of rubber, showed a delay after the addition of GO. Field emission scanning electron microscopy was employed to confirm the uniform dispersion of filler in the matrix. Indeed, with increasing fillers loading, the torque, tensile strength, thermal stability and crosslink density of obtained nanocomposites were improved. These results were correlated to the better dispersion of fillers through the rubber matrix.

The general manufacturing problem can be described as the achievement of a predefined product quality with given equipment, cost and time constraints. Unfortunately, for some quality characteristics of a product such as surface roughness it is hard to ensure that these requirements will be met. Stainless steels STS 304 is frequently used as shaft materials in small fiber reinforced polymer(FRP) fishing boats. In this work, the dry turning parameters of STS 304 are optimized by using Taguchi method. The experiments were conducted at three different cutting speeds with three different feed and three different depth of cut. The cutting parameters are optimized using signal to noise ratio and the analysis of variance. The effects of cutting speed and feed on surface roughness was analyzed. The results revealed that the spindle speed is the more significant parameter influencing the surface roughness.

This paper presents a Technology-CAD (TCAD) simulation of the characteristics of crystalline Si pillar array solar cells. The junction depth and the surface concentration of the solar cells were optimized to obtain the targeted sheet resistance of the emitter region. The diffusion model was determined by calibrating the emitter doping profile of the microscale silicon pillars. The dimension parameters determining the pillar shape, such as width, height, and spacing were varied within a simulation window from ${\sim}2{\mu}m$ to $5{\mu}m$. The simulation showed that increasing pillar width (or diameter) and spacing resulted in the decrease of current density due to surface area loss, light trapping loss, and high reflectance. Although increasing pillar height might improve the chances of light trapping, the recombination loss due to the increase in the carrier's transfer length canceled out the positive effect to the photo-generation component of the current. The silicon pillars were experimentally formed by photoresist patterning and electroless etching. The laboratory results of a fabricated Si pillar solar cell showed the efficiency and the fill factor to be close to the simulation results.

To research the electrical properties of ZnS thin films with various annealing conditions, ZnS was prepared by RF magnetron sputtering system and annealed in a vacuum for 10 minutes. All films were analyzed by the XRD, PL and I-V measurement system. The XRD pattern of ZnS film annealed at $100^{\circ}C$ was shifted to lower 2 theta because of the formation of a depletion region at the interface between a substrate and ZnS thin film, and the capacitance was abruptly increased. However, the pattern of XRD of ZnS film annealed at $100^{\circ}C$ with a Schottky contact was showed the amorphous structure, and the current-voltage characteristics were non-linearly observed by the Schottky contact.

Nowadays, smart phone is being popularly used for communication, entertainment, and information retrieval. While demands on video traffic over mobile networks increases sharply, the wireless link capacity is often limited to fully support the traffic demand. Therefore, the size of video data needs to be reduced to provide high quality video with limited capacity. To handle this issue, we propose a video editing system using the ffmpeg library. The proposed system can provide a high quality video with a relatively small data size, thereby facilitating the mobile streaming services and live-video games.

The purpose of this study is to investigate the user satisfaction of kiosk contents installed at bus stops in Seoul. A total of 400 kiosks, which are touch-based traffic information systems, are installed and operated, providing contents such as bus routes, marginal area, seoul tourism, life information, angel donation, transportation cards, magnifier and boarding requests. The study results showed that the user satisfaction scores of bus routes and transportation cards were high, but it was necessary to improve other contents. The results of this study will be used as basic data to propose user experience(UX) of public service design. We will also use it as content guidelines for public information kiosks to be developed in the future.

Today's young generation users are very active in expressing themselves through smart phones, form networks in this cyber space and express their identities freely. Therefore, this study aims to investigate how young people in their 20s are expressing themselves through smart phones and the differences from the attempt of self-expression in the existing cyber space. The research method was an in-depth interview, which was a qualitative research method, aimed at people in their 20s, so that they could freely talk about their thoughts and feelings. In-depth interviews are useful for users' psychological and in-depth analysis of behavior.

One of the most critical aspects of the modern semiconductor industry is the quality of wafer surface, the roughness of which is mostly caused by the ingot slicing. And the grinding is supposed to be the main process to reduce the surface roughness. The vibrations of the disc surface grinder are the major problem to effectively achieve the required surface quality. In this study, the structure of a disc surface grinder was analyzed through the experiment and the computer simulation to investigate the dynamic characteristics of the machine, and further to alter the design for the improved stability. The result of the study shows that simple design alterations without alternating main body can effectively suppress the vibrations of the machine.

In this paper, IGZO thin film transistor (TFT) was fabricated with cross-linked Poly (4-vinylphenol) (PVP) gate dielectric for flexible, transparent display applications. The PVP is one of the candidates for low-temperature gate insulators. MIM structure was fabricated to measure the leakage current and evaluate the insulator properties according to the annealing temperature. Low leakage current ( <0.1nA/cm2 @ 1MV/cm ) was observed at $200^{\circ}C$ annealing condition and decreases much more as the annealing temperature increases. The electrical characteristics of IGZO TFT such as subthreshold swing, mobility and ON/OFF current ratio were also improved, which shows that the performance of IGZO TFTs with PVP can be enhanced by reducing the amount of incomplete crosslinking in PVP.

Currently, the size of the electronic device is in the nano area. In order to control the movements of these nanoscale devices, one should be able to understand the physical phenomena in the nano area. Recently, due to carbon nanotubes and mechanical outstanding electrical conductivity and mechanical characteristics of the carbon nanotubes and Graphene behaves to apply. Efforts have been active. There are various tubes with a radius of a in a compact mass in the form of a Multi walled carbon nanotubes in different between the radius. Van der Waals force can move smoothly without friction with each other by the nanoscale motor turning, using the properties, making. This is the lightest solids per unit area on the thickness is electrical atomic layer one of the substance and the electrical conductivity, the best material and mechanical characteristics are very much. Many studies because great is the ideal nanoelectromechanical device of material is being considered. In this study, electrical resonator for a new structure proposed and the nature and methodology would like to come up.

When a substrate with a pixel-defining layer (bank) is coated, there arises capillary force due to surface tension and adhesive forces between a solvent and the bank layer. It brings in a degradation of film thickness and emission uniformities within pixels. With an attempt to suppress it, we have performed fluid flow simulations of capillary arise by varying the contact angle of bank and the bank structure. We have first demonstrated that the fluid flow model can reproduce the capillary phenomenon that was observed experimentally. It has been found that capillary arise can be suppressed using a hydrophobic material for the bank layer. Furthermore, it was suppressed by tilting the sidewalls outwardly (i.e., using a positive photoresistor). We can obtain very uniform films when the slope is $50^{\circ}$ with the contact angle of $40^{\circ}$.

ITO thin films were grown on the glass substrate under various oxygen gas flow and substrate temperature by using FTS (Facing Target Sputtering) system. To investigate properties of as-prepared films for transparent electrical devices, we employed four-point probe, UV-VIS spectrometer, X-ray diffractometer (XRD), scanning electron microscopy (SEM), Hall Effect measurement system and Atomic Force Microscope (AFM). As a results, all of prepared samples has high transmittance of over 80 % in the visible range (300-800 nm). Their resistivity increased as a function of oxygen gas flow and substrate temperature due to their crystal structure and oxygen defect in the films. As-prepared films have a resistivity of under $10^{-4}({\Omega}-cm)$.

In this paper, natural convection around the ambient evaporator was numerically studied using commercial computational fluid dynamics software. From the simulations, temperature and velocity fields around the evaporator were found as a function of evaporator size and liquefied gas flow rate. The heat transfer coefficient at the external surface of the evaporator was also calculated from the simulation results. In order to give the heat transfer coefficient for various conditions, correlation between Rayleigh number and Nusselt number was proposed.