• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.15 no.1
• /
• pp.51-61
• /
• 1997

A two-dimensional numerical tidal model with $1/3^\circ$ resolution has been established to investigate the distribution of semidiurnal constituents$(M_2,\;S_2,\;K_2,\;N_2)$ and diurnal constituents$(K_1,\;O_1,\;P_1,\;Q_1)$ of the global ocean. The $1/3^\circ$ numerical model has been applied to the computation of detailed tidal distributions in the marginal seas and the shelf seas. Tidal characteristics in shallow areas could be hardly resolved with the existing global chart due to the low resolution. Computed tidal charts obtained by $1/3^\circ$ numerical model have been compared with the existing global charts and the altimetry-derived tidal charts. Computed harmonic constants have also been com-pared with the pelagic tidal observations. The results obtained with fine-grid numerical model can be used to determine the time-independent sea surface topography by removing the tidal components from the altimetry-derived sea surface height.

• Smart Structures and Systems
• /
• v.15 no.4
• /
• pp.997-1018
• /
• 2015

Structural health monitoring along with damage detection and assessment of its severity level in non-accessible reinforced concrete members using piezoelectric materials becomes essential since engineers often face the problem of detecting hidden damage. In this study, the potential of the detection of flexural damage state in the lower part of the mid-span area of a simply supported reinforced concrete beam using piezoelectric sensors is analytically investigated. Two common severity levels of flexural damage are examined: (i) cracking of concrete that extends from the external lower fiber of concrete up to the steel reinforcement and (ii) yielding of reinforcing bars that occurs for higher levels of bending moment and after the flexural cracking. The purpose of this investigation is to apply finite element modeling using admittance based signature data to analyze its accuracy and to check the potential use of this technique to monitor structural damage in real-time. It has been indicated that damage detection capability greatly depends on the frequency selection rather than on the level of the harmonic excitation loading. This way, the excitation loading sequence can have a level low enough that the technique may be considered as applicable and effective for real structures. Further, it is concluded that the closest applied piezoelectric sensor to the flexural damage demonstrates higher overall sensitivity to structural damage in the entire frequency band for both damage states with respect to the other used sensors. However, the observed sensitivity of the other sensors becomes comparatively high in the peak values of the root mean square deviation index.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.2
• /
• pp.156-162
• /
• 2012

Outlier detection and treatment process is highly required as the first step for the statistical analysis of the monitoring data having many outliers frequently occurred in the coastal environmental monitoring projects. In this study, the outlier detection method using the approximate and detail (or residual) components of the (raw) data is suggested. The approximate and detail components of the data can be separated by the diverse filtering and smoothing methods. The decomposition of the data is carried out by the harmonic analysis and local regression curve, respectively. Then, the Grubbs' test and modified z-score method widely used to detect outliers in the data are applied to the detail components of the water temperature data. The new data set is reconstructed after removed the outliers detected by these methods. It can be shown that the suggested process is successfully applied to the outlier detection of the coastal water temperature monitoring data provided by the Real-time Information System for Aquaculture Environment, National Fisheries Research and Development Institute (NFRDI).

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1020-1022
• /
• 2001

because the output of solar cell is direct, it is necessary to install D/A converter system for A.C load, and in case of driving utility line system, it is possible to drive system relation when the system supplies sinusodal current ant voltage having unit power factor. As the characteristics of the soar cell output the is influenced by dailysunight charge, for more electric power it is essential to control the direction toward the san so that the driving point of solar cell can always operate near maximum output point. PWM modulation device among electric power converters must have stable modulation at anytime when it includes noise-factors such as noise-wave and noises on electric voltage wave, a synchronous signal system. In dealing with synchronous signal for control and control signal by microprocessor, it is necessary to compensate it because there is time difference between sample paint and carrier wave. On this papers, single phase PWM current type invertor controled the solar cell having typical voltage dropping character has optimun short current in short, reduces D.C reactance, composes controller for modulation and keeps lower harmonic and high power factor keeping maximum output of solar cell according daily sunlight charge variation.

• Smart Structures and Systems
• /
• v.14 no.3
• /
• pp.327-345
• /
• 2014

This paper presents a composite control strategy for the active suppression of vibration due to the unknown disturbances, such as external excitation, harmonic effects and control spillover, as well as high-frequency accelerometer measurement noise in the all-clamped stiffened plate. The proposed composite control action based on the modal approach, consists of two contributions including feedback part and feedforward part. The feedback part is the well-known PID controller, which is widely used to increase the structure damping and improve its dynamic performance close to the resonance frequencies. In order to get better performance for vibration suppression, the weight matrixes is optimized by chaos sequence. Then an improved disturbance observer (IDOB) as the feedforward compensation part is developed to enhance the vibration suppression performance of PID under various disturbances and uncertainties. The proposed IDOB can simultaneously estimate the various disturbances dynamically as well as measurement noise acting on the system and suppress them by feedforward compensation design. A rigorous analysis is also given to show why the IDOB can effectively suppress the unknown disturbances and measurement noise. In order to verify the proposed composite control algorithm (IDOB-PID), the dSPACE real-time simulation platform is used and an experimental platform for the all-clamped stiffened plate active vibration control system is set up. The experimental results demonstrate the effectiveness, practicality and strong anti-disturbances ability of the proposed control strategy.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.2
• /
• pp.122-133
• /
• 2013

An arbiter-based simple phase decision circuit (PDC) optimized for high-resolution phase-to-digital converter made up of an analog phase-frequency detector and a time-to-digital converter for all-digital phase-locked loops is proposed. It can distinguish very small phase difference between two pulses even though it consumes lower power and has smaller input-to-output delay than the previously reported PDC. Proposed PDC is realized using 130-nm CMOS process and demonstrated by transistor-level simulations. A 5-bit P2D having no offset nor deadzone using the PDC is also demonstrated. A harmonic-lock-free and small-phase-offset delay-locked loop for fixing the P2D resolution regardless of PVT variations is also proposed and demonstrated.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.180-184
• /
• 2013

In this paper, a low power antenna switch controller IC is designed using a silicon-on-insulator (SOI) CMOS technology. To improve power handling capability and harmonic distortion performance of the antenna switch, the proposed antenna switch controller provides 3-state logic level such as +VDD, GND, and -VDD for the gate and body of switch of FETs according to decoder signal. By employing input-coupled current ring oscillator and hardware efficient level shifter, the proposed controller greatly reduces power consumption and hardware complexity. It consumes 135 ${\mu}A$ at a 2.5 V supply voltage in active mode, and occupies $1.3mm{\times}0.5mm$ in area. In addition, it shows fast start-up time of 10 ${\mu}s$.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.858-864
• /
• 2014

Recently, many researches have shown that even photosynthetic light-harvesting pigment-protein complexes can have quantum coherence in their excitonic energy transfer at cryogenic and physiological temperatures. Because the protein supplies such noisy environment around pigments that conventional wisdom expects very short lived quantum coherence, elucidating the mechanism and searching for an applicability of the coherence have become an interesting topic in both experiment and theory. We have previously studied the quantum coherence of a phycocyanin 645 complex in a marine algae harvesting light system, using Poisson mapping bracket equation (PBME). PBME is one of the applicable methods for solving quantum-classical Liouville equation, for following the dynamics of such pigment-protein complexes. However, it may suffer from many defects mostly from mapping quantum degrees of freedom into classical ones. To make improvements against such defects, benchmarking targets with more accurately described dynamics is highly needed. Here, we fall back to reduced hierarchical equation of motion (HEOM), for such a purpose. Even though HEOM is known to applicable only to simplified system that is coupled to a set of harmonic oscillators, it can provide ultimate accuracy within the regime of quantum-classical description, thus providing perfect benchmark targets for certain systems. We compare the evolution of the density matrix of pigment excited states by HEOM against the PBME results at physiological temperature, and observe more sophisticated changes of density matrix elements from HEOM. In PBME, the population of states with intermediate energies display only monotonically increasing behaviors. Most importantly, PBME suffers a serious issue of wrong population in the long time limit, likely generated by the zero-point energy leaking problem. Future prospects for developments are briefly discussed as a concluding remark.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.2
• /
• pp.152-160
• /
• 2011

The electromagnetic characteristics of FCEVs (fuel cell electric vehicles) are much different from the existing combustion engine cars as well as hybrid, plug-in-hybrid, and pure electric vehicles due to the high voltage/current generated by a fuel cell stack which uses a compressed hydrogen gas reacted with oxygen. To operate fuel cell stack efficiently, BOP (Balance of Plant) which is consisted of many motors in water pump, air blower, and hydrogen recycling pump as well as inverters for these motors is essential. Furthermore, there are also electric systems for entertainment, information, and vehicle control such as navigation, broadcasting, vehicle dynamic control systems, and so on. Since these systems are connected by high voltage or general cables, EMC (Electromagnetic compatibility) analysis for high voltage and general cable of FCEV is the most important element to prevent the possible electric functional safety errors. In this paper, electromagnetic fields by high voltage and general cables for FCEVs is studied. From numerical analysis results, total time harmonic electromagnetic field strength from high voltage and general cables have difference of 13~16 dB due to ground effect by impedance matching. The EMI results of FECV at 10 m distance shows difference of 41 dB at 30 MHz and 54 dB at 230 MHz compared with only general cable routing.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.1
• /
• pp.197-204
• /
• 2010

This paper proposes a new body-effect compensated switch configuration for low voltage and low distortion switched-capacitor (SC) applications. The proposed circuit allows rail-to-rail switching operation for low voltage SC circuits and has better total harmonic distortion than the conventional bootstrapped circuit by 19 dB. A 2-1 cascaded sigma-delta modulator is provided for performing the high-resolution analog-to-digital conversion on audio codec in a communication transceiver. An experimental prototype for a single-stage folded-cascode operational amplifier (opamp) and a 2-1 cascaded sigma-delta modulator has been implemented m a 0.25 micron double-poly, triple-metal standard CMOS process with 2.7 V of supply voltage. The 1% settling time of the opamp is measured to be 560 ns with load capacitance of 16 pF. The experimental testing of the sigma-delta modulator with bit-stream inspection and analog spectrum analyzing plot is performed. The die size is $1.9{\times}1.5\;mm$.