• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.172-174
• /
• 1988

Studies and measurements of open circuit voltage in a metal/insulator/metal structure where metal are electrodes, when the insulator molecules have dipole moments all oriented parallel to each other have been reported here. The measured voltage has been shown to be directed related to the dipole moment of the molecules in the films. The insulator ultra thin films was deposited on them by the Langmuir-Blodgett technique to obtain the structure referred to as z type and Hetero structure of LB films.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.3
• /
• pp.361-369
• /
• 2004

A metal fiber bed has seldom been applied to the practical filtration process despite its excellent mechanical and chemical stability. The filter-bed used in this work was highly porous with open structure, of which apparent porosity was 80 ∼ 90%. Although pressure loss across the filter-bed was very low, separation efficiency was found to be quite high. This paper focuses on the basic filtration mechanisms of a metal filter-bed and a thin ceramic filter from fly ash for reference. The experimental parameters were face velocity, dust loading and porosity of filter-bed. Pressure drop increased with increasing face velocity and dust feeding load for both filters. It also showed that dust particles deposited in the deep flow path, finally resulting in clogging the pore channels. It thereby indicates that the dominating mechanism of the metal filter-bed would be depth filtration. Meanwhile, the thin fly ash composite filters trapped the aerated dust mainly on the surface of the filter medium, so that the instantaneously formed dust layer might cause a steep increase of pressure drop across the filtration system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.571-574
• /
• 2009

Metal oxide/metal bilayer structures are explored as contacts with a low injection barrier in organic thin-film transistors (OTFTs) in an effort to realize their true potential for low-cost electronics. OTFTs with a bilayer electrode of $WO_3$ (10nm) and Al shows a saturation mobility as large as 0.97 $cm^2$/Vsec which are comparable to those of Au-based control samples (~0.90 $cm^2$/Vsec). Scaling of contact resistance with respect to the thickness of $WO_3$ layer is also discussed.

• Journal of Ceramic Processing Research
• /
• v.20 no.5
• /
• pp.484-489
• /
• 2019

VO2 is an attractive candidate as a transition metal oxide switching material as a selection device for reduction of sneak-path current. We demonstrate deposition of nanoscale VO2 thin films via thermal atomic layer deposition (ALD) with H2O reactant. Using this method, we demonstrate VO2 thin films with high-quality characteristics, including crystallinity, reproducibility using X-ray diffraction, and X-ray photoelectron spectroscopy measurement. We also present a method that can increase uniformity and thin film quality by splitting the pulse cycle into two using scanning electron microscope measurement. We demonstrate an ON / OFF ratio of about 40, which is caused by metal insulator transition (MIT) of VO2 thin film. ALD-deposited VO2 films with high film uniformity can be applied to next-generation nonvolatile memory devices with high density due to their metal-insulator transition characteristic with high current density, fast switching speed, and high ON / OFF ratio.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.2
• /
• pp.38-42
• /
• 2015

Atomic layer deposition (ALD) is essential for the fabrication of nanoscale electronic devices because it has excellent conformality, atomic scale thickness control, and large area uniformity. Metal thin films are one of the important material components for electronic devices as a conductor. As the size of electronic devices shrinks, the thickness of metal thin films is decreased down to few nanometers, and the metal films become non-continuous due to inherent island growth of metal below a critical thickness. So, fabrication of continuous metal thin films by ALD is fundamentally and practically important. Since ALD films are grown through self-saturated reactions between precursors on surface, initial growth characteristics significantly depend on the surface properties and the selection of precursors. In this work, we investigated ALD Pt on $TiO_2$ substrate by using trimethyl-methyl-cyclopentadienyl-Platinum ($MeCpPtMe_3$) precursor and $O_3$ reactant. By using $O_3$ instead of $O_2$, initial nucleation rate of ALD Pt was increased on $TiO_2$ surface, resulting in formation of continuous thin Pt films. Morphologies of ALD Pt on $TiO_2$ were characterized by using Scanning Electron Microscope (SEM) and Energy-Dispersive X-ray Spectroscopy (EDS). Crystallinity of ALD Pt on $TiO_2$ correlated with its growth characteristics was analyzed by X-Ray Diffraction (XRD).

• Journal of Sensor Science and Technology
• /
• v.29 no.4
• /
• pp.255-260
• /
• 2020

In this study, we developed a method of improving the surface-enhanced Raman spectroscopy (SERS) response characteristics by depositing a nanoporous Ag metal thin film through cluster source sputtering after forming a pyramidal texture structure on the Si substrate surface. A reactive ion etching (RIE) system with a metal mesh inside the system was used to form a pyramidal texture structure on the Si surface without following a complicated photolithography process, unlike in case of the conventional RIE system. The size of the texture structure increased with the RIE process time. However, after a process time of 60 min, the size of the structure did not increase but tended to saturate. When the RF power increased from 200 to 250 W, the size of the pyramidal texture structure increased from 0.45 to 0.8 ㎛. The SERS response characteristics were measured by depositing approximately 1.5 ㎛ of nanoporous Ag metal thin film through cluster sputtering on the formed texture structure by varying the RIE process conditions. The Raman signal strength of the nanoporous Ag metal thin film deposited on the Si substrate with the texture structure was higher than that deposited on the general silicon substrate by up to 19%. The Raman response characteristics were influenced by the pyramid size and the number of pyramids per unit area but appeared to be influenced more by the number of pyramids per unit area. Therefore, further studies are required in this regard.

• Current Applied Physics
• /
• v.18 no.12
• /
• pp.1577-1582
• /
• 2018

While controlling the cation contents in perovskite rare-earth nickelate thin films, a metal-to-insulator phase transition is reported. Systematic control of cation stoichiometry has been achieved by manipulating the irradiation of excimer laser in pulsed laser deposition. Two rare-earth nickelate bilayer thin-film heterostructures with the controlled cation stoichiometry (i.e. stoichiometric and Ni-excessive) have been fabricated. It is found that the Ni-excessive nickelate film is structurally less dense than the stoichiometric film, albeit both of them are epitaxial and coherent with respect to the underlying substrate. More interestingly, as a temperature decreases, a metal-to-insulator transition is only observed in the Ni-excessive nickelate films, which can be associated with the enhanced disproportionation of the Ni charge valence. Based on our theoretical results, possible origins (e.g. anti-site defects) of the low-temperature insulating state are discussed with the need of future work for deeper understanding. Our work can be utilized to realize unusual physical phenomena (e.g. metal-to-insulator phase transitions) in complex oxide films by manipulating the chemical stoichiometry in pulsed laser deposition.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.401-405
• /
• 2017

Because silicon thin film solar cells have a high absorption coefficient in visible light, they can absorb 90% of the solar spectrum in a $1-{\mu}m$-thick layer. Silicon thin film solar cells also have high transparency and are lightweight. Therefore, they can be used for building integrated photovoltaic (BIPV) systems. However, the contact electrode needs to be replaced for fabricating silicon thin film solar cells in BIPV systems, because most of the silicon thin film solar cells use metal electrodes that have a high reflectivity and low transmittance. In this study, we replace the conventional aluminum top electrode with a transparent aluminum-doped zinc oxide (AZO) electrode, the band level of which matches well with that of the intrinsic layer of the silicon thin film solar cell and has high transmittance. We show that the AZO effectively replaces the top metal electrode and the bottom fluorine-doped tin oxide (FTO) substrate without a noticeable degradation of the photovoltaic characteristics.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.28-32
• /
• 2010

Technical demands for aspheric glass lens formed in market increases its application from simple camera lens module to fiber optics connection module in optical engineering. WC is often used as a metal core of the aspheric glass lens, but the long life time is issued because it fabricated in high temperature and high pressure environment. High hard thin film coating of lens core increases the core life time critically. Diamond Like Carbon(DLC) thin film coating shows very high hardness and low surface roughness, i.e. low friction between a glass lens and a metal core, and thus draw interests from an optical manufacturing industry. In addition, DLC thin film coating can removed by etching process and deposit the film again, which makes the core renewable. In this study, DLC films were deposited on the SiC ceramic core. The process variable in FVA(Filtered Vacuum Arc) method was the substrate bias-voltage. Deposited thin film was evaluated by raman spectroscopy, AFM and nano indenter and measured its crystal structure, surface roughness, and hardness. After applying optimum thin film condition, the life time and crystal structure transition of DLC thin film was monitored.

• Journal of the Korean Ceramic Society
• /
• v.42 no.11 s.282
• /
• pp.763-769
• /
• 2005

Ferroelectric $ReMnO_3$(Re:Ho, Er) thin films were deposited on Si(100) substrate by Metal-Organic Chemical Vapor Deposition (MOCVD). Crystallinity and electric properties of $ReMnO_3$(Re:Ho, Er) thin films were investigated as a function of thermal heat treatment process, CHP (Conventional Heat-treatment Process) and RTP (Rapid Thermal Process). $ReMnO_3$(Re:Ho, Er) thin films prepared by RTP showed higher c-axis preferred orientation and homogeneous surface roughness than those prepared by CHP. The remnant polarization of ferroelectric hysteresis loop of $ReMnO_3$(Re:Ho, Er) thin films was strongly dependent on the c­axis preferred orientation of hexagonal single phase, and the leakage current characteristics of thin films were dependent on the homogeneity of grain size as well as surface roughness of thin films.