• 한국재료학회지
• /
• 제7권11호
• /
• pp.964-968
• /
• 1997

Si(001)기판 위에 형성시킨 Zr-silicide의 전기적, 물리적 특성에 관한 연구를 하였다. Zr 박막은 전자빔 증착기를 사용하여 증착하였으며, 50$0^{\circ}C$ 열처리하여 Zr-silicide를 형성시켰다. 각 온도에서 열처리된 Zr-silicide시편의 상형성, 전기적 특성, 화학적 조성, 표면 및 계면 형상을 XRD, four-point probe, AES, TEM과 HRTEM으로 분석하였다. 분석 결과 $600^{\circ}C$부터 Zr과 Si기판의 계면에서 C49 ZrSi$_{2}$의 생성이 관찰되었다. Zr-Silicide박막의 비저항은 C49 ZrSi$_{2}$의 형성에 영향을 받는 것으로 관찰되었으며, 50$0^{\circ}C$ 열처리 후에는 184.3 $\mu$Ω-cm로 낮아졌으며, C49 ZrSi$_{2}$가 박막에 완전히 형성된 80$0^{\circ}C$ 열처리 후에는 32$\mu$Ω-cm의 낮은 저항을 나타내었다. 형성된 C49 ZrSi$_{2}$박막은 균질한 화학적 조성을 하고 있음을 AES 분석으로 확인하였다. Zr-silicide의 표면 및 계면의 형상을 TEM과 HRTEM으로 관찰하였으며, $600^{\circ}C$ 열처리 후에 계면에서 ZrSi$_{2}$의 상형성이 시작되는 것을 관찰하였다. 80$0^{\circ}C$ 열처리 후에도 계면과 표면형상은 비교적 균질한 형상이 유지되었음이 관찰되었으며, 이는 C49 ZrSi$_{2}$가 높은 온도에서도 잘 응집되지 않으며 고온 안정성을 가지는 재료임이 관찰되었다.

• 한국재료학회지
• /
• 제13권11호
• /
• pp.711-716
• /
• 2003

Gate length, height, and silicide thickness have all been shrinking linearly as device density has progressively increased over the years. We investigated the effect of the cobalt diffusion during the silicide formation process on the 60$\AA$-thick gate oxide lying underneath the Ti/Co and Co/Ti bilayers. We prepared four different cobalt silicides, which have similar sheet resistance, made from the film structure of Co/Ti(interlayer), and Ti(capping layer)/Co, and peformed the current-voltage, time-to-break down, and capacitance-voltage measurements. Our result revealed that the cobalt silicide process without the Ti capping layer allowed cobalt atoms to diffuse into the upper interface of gate oxides. We propose that 100$\AA$-thick titanium interlayer may lessen the diffusion of cobalt to gate oxides in 1500-$\AA$ height polysilicon gates.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.15-16
• /
• 2006

The thermal stability of nickel silicide with compressively and tensilely stressed nitride capping layer has been investigated in this study. The Ni (10 nm) and Ni/Co/TiN (7/3/25 nm) structures were deposited on the p-type Si substrate. The stressed capping layer was deposited using plasma enhanced chemical vapor deposition (PECVD) after silicide formation by one-step rapid thermal process (RTP) at $500^{\circ}C$ for 30 sec. It was found that the thermal stability of nickel silicide depends on the stress induced by the nitride capping layer. In the case of Ni (10 nm) structure, the high compressive sample shows the best thermal stability, whereas in the case of Ni/Co/TiN (7/3/25 nm) structure, the high compressive sample shows the worst thermal stability.

• 한국통신학회논문지
• /
• 제15권5호
• /
• pp.399-405
• /
• 1990

急速 熱處理 공정을 高融點 타이타늄 실리사이드 형성을 위한 反應率의 연구와 정확한 形成 調節에 이용하였다. 試料는 n형 실리콘과 다결정 웨이퍼이며, 타이타늄을 스퍼터로 증착시켰다. 工程은 질소와 아르곤 가스 분위기 下에 실리사이드 형성을 정확하게 조절하기 위해 急速 時間 溫度 분포의 行列로 수행하였다. 반응된 박막은 面抵抗 측정과 전자현미경 사진, 自動分 抛抵抗 측정, X-선 回折 등으로 分析하였다. 結果는 실리사이드의 抵抗度는 20$\mu$$\Omega$-cm이하 이고, 박막 두께는 타이타늄 燕着 의 두께보다 약 2배로 나타났다. 실리사이드 形成 분위기는 아르곤과 窒素가 同一한 溫度 時間 조건에서 形成되었다.

• 한국전기전자재료학회논문지
• /
• 제19권11호
• /
• pp.1000-1004
• /
• 2006

In this paper, thermal stability of Ni-silicide formed on the SOI substrate with $B_{11}$ has been characterized. The sheet resistance of Ni-silicide on un-doped SOI and $B_{11}$ implanted bulk substrate was increased after the post-silicidation annealing at $700^{\circ}C$ for 30 min. However, in case of $B_{11}$ implanted SOI substrate, the sheet resistance showed stable characteristics after the post-silicidation annealing up to $700^{\circ}C$ for 30 min. The main reason of the excellent property of $B_{11}$ sample is believed to be the retardation of Ni diffusion by the boron and bottom oxide layer of SOI. Therefore, retardation of Ni diffusion is highly desirable lot high performance Ni silicide technology.

• 한국표면공학회지
• /
• 제29권1호
• /
• pp.3-14
• /
• 1996

High temperature anneal of W-rich silicides, inferior to adherence compared with Si-rich silicides, resulted in the film peeling off from the Si-substrate when WSix thickness reached more than critical thickness. Investigation of the W-rich silicide films peeling off from the substrate revealed that the voids underneath the $WSi_2$ produced through silicide reaction were responsible for the poor adherence of W-rich silicide. In addition, internal stress in the film increased as the silicide thickness increased. In order to promote the adhesion of WSix to Si-substrate, thin Ti-layer was formed between WSi and Si-substrate(WSix/Ti/Si). No voids were observed in $WSi_2$/Ti/Si $N_2$-annealed at $1000^{\circ}C$, thereby leading to an increase of the critical thickness from ～1700$\AA$ to more than 2500$\AA$. However, higher resisiti-vity was obtained in WSix/Ti/Si than in WSix/Si. Finally, different silicide reaction mechanism for the structures(WSix/Si, WSix/Ti/Si) was proposed to explain the formation of voids as well as the role of thin Ti-layer.

• 한국분말재료학회지
• /
• 제25권5호
• /
• pp.402-407
• /
• 2018

Molybdenum silicide has gained interest for high temperature structural applications. However, poor fracture toughness at room temperatures and low creep resistance at elevated temperatures have hindered its practical applications. This study uses a novel powder metallurgical approach applied to uniformly mixed molybdenum silicide-based composites with silicon carbide. The degree of powder mixing with different ball milling time is also demonstrated by Voronoi diagrams. Core-shell composite powder with Mo nanoparticles as the shell and ${\beta}-SiC$ as the core is prepared via chemical vapor transport. Using this prepared core-shell composite powder, the molybdenum silicide-based composites with uniformly dispersed ${\beta}-SiC$ are fabricated using pressureless sintering. The relative density of the specimens sintered at $1500^{\circ}C$ for 10 h is 97.1%, which is similar to pressure sintering owing to improved sinterability using Mo nanoparticles.

• 전자공학회논문지A
• /
• 제33A권3호
• /
• pp.126-134
• /
• 1996

Tungsten silicide films were deposited on the phosphorus-doped poly-Si/SiO$_{2}$/Si-substrates by LPCVD (low pressue chemical vapor deposition). The formation and various properties of tungsten silicide processed by furnace annealing in N$_{2}$ ambient were evaluated by using XRD. AFM, 4-point probe and SEM. And the redistribution of phosphorus atoms has been observed by SIMS. The crystal structure of the as-deposited tungsten silicide films were transformed from the hexagonal to the tetragonal structure upon annealing at 550.deg. C. The surface roughness of tungsten polycide films were found to very smoothly upon annelaing at 850.deg. C and low phosphorus concentration in polysilicon layer. The sheet resistance of tungsten polycide low phosphorus concentration in polysilicon layer. The sheet resistance of tungsten polycide films are measured to be 2.4 .ohm./ㅁafter furnace annealing at 1100.deg. C, 30min. It was found that the sheet resistance of tungsten polycide films upon annealing above 1050.deg. C were independant on the phosphorus concentration of polysilicon layer and furnace annealing times. An out-diffusion of phosphorus impurity through tungsten silicide film after annealing in $O_{2}$ ambient revealed a remarkably low content of dopant by oxide capping.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권1호
• /
• pp.22-27
• /
• 2013

Detailed study on how the plasma process during the sidewall spacer formation suppresses the formation of silicide is done. In non-patterned wafer test, it is found that both fluorocarbon reactive ion etch (RIE) and TEOS plasma-enhanced deposition processes modify the Si surface so that the silicide reaction is chemically inhibited or suppressed. In order to investigate the cause of the chemical modification, we analyze the elements on the silicon surface through Auger Electron Spectroscopy (AES). From the AES result, it is found that the carbon induces chemical modification which blocks the reaction between silicon and nickel. Thus, protecting the surface from the carbon-containing plasma process prior to nickel deposition appears critical in successful silicide formation.

• Transactions on Electrical and Electronic Materials
• /
• 제9권2호
• /
• pp.47-51
• /
• 2008

In this paper, thermal stability of Nickel silicide formed on p-type silicon wafer using Ni-V alloy film was studied. As compared with pure Ni, Ni-V shows better thermal stability. The addition of Vanadium suppresses the phase transition of NiSi to $NiSi_2$ effectively. Ni-V single structure shows the best thermal stability compared with the other Ni-silicide using TiN and Co/TiN capping layers. To enhance the thermal stability up to $650^{\circ}C$ and find out the optimal thickness of Ni silicide, different thickness of Ni-V was also investigated in this work.