• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.2065-2069
• /
• 2014

The DAC-7512E is a 12-bit digital to analog converter that is low power and a single package with internal buffers. The DAC-7512E takes up minimal PCB area for applications of space power electronics design. The spacecraft mass is a crucial point considering spacecraft launch into space. Therefore, we have performed a TID test for the DAC-7512E 12-bit serial input digital to analog converter to reduce the spacecraft mass by using a low-level Gamma-ray irradiator with $Co^{60}$ gamma-ray sources. The irradiation with $Co^{60}$ gamma-rays was carried out at doses from 0 krad to 100 krad to check the error status of the device in terms of current, voltage and bit error status during conversion. The DAC-7512E 12-bit serial digital to analog converter should work properly from 0 krad to 30 krad without any error.

• Journal of Information Display
• /
• v.2 no.2
• /
• pp.1-6
• /
• 2001

A $1"{\times}l"$, $512{\times}512$ poly-Si TFT-LCD with a new integrated 8-bit parallel-serial digital data driver was proposed and designed. For high resolution, the proposed parallel-serial digital driver used serial video data rather than parallel ones. Thus, digital circuits for driving one column line could be integrated within very small width. The parallel-serial digital data driver comprised of shift registers, latches, and serial digital-to-analog converters (DAC's). We designed a $1"{\times}l"$, $512{\times}512$ poly-Si TFT-LCD with integrated 8-bit parallel-serial digital data drivers by a circuit simulator which has physical-based analytical model of poly-Si TFT's. The fabricated shift register well operated at 2 MHz and $V_{DD}$=10V and the fabricated poly-Si TFT serial DAC's, which converts serial digital data to an analog signal, could convert one bit within $2.8{\mu}s$. The driver circuits for one data line occupied $8100{\times}50{\mu}m^2$ with $4{\mu}m$ design rule.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.841-842
• /
• 2006

This paper has proposed a serial 8-bit DAC for column driver circuits of mobile displays using LTPS TFTs. The DAC circuit takes very small area by using parasitic capacitance of column lines as sampling and holding capacitors. Moreover, the proposed DAC does not need the analog buffer, because the DAC operation is performed on the column lines. For the data driver circuits of 2-inch qVGA OLED panel, the DAC area is $84um{\times}800um$ and the simulated DAC power consumption is 8.5mW with 10-V supply voltage.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.1
• /
• pp.33-41
• /
• 2019

We propose an embedded solution to design a high-speed and high-accuracy 16bit analog-digital signal processing interface for the control systems using various external analog signals. Choosing TMS320F28377D micro controller unit (MCU) featuring high-performance processing in the 32-bit floating point operation, low power consumption, and various I/O device supports, we design and build the proposed system that supports both 16-bit analog-digital converter (ADC) interface and high precision digital-analog converter (DAC) interface. The ADC receives voltage-level differential signals from fully differential amplifiers, and the DAC communicates with MCU through 50 MHz bandwidth high-fast serial peripheral interface (SPI). We port the boot loader and device drivers to the implemented board, and construct the firmware development environment for the application programming. The performance of the entire implemented system is demonstrated by analog-digital signal processing tests, and is verified by comparing the test results with those of existing similar systems.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.111.3-111
• /
• 2001

Automative system and robot are operated by motor. Recently, automative system and robot need correct operation and control for precise task. Therefore they need precise motor control technology. In present, controller needs precise motor control technology in automative system and robot. Usual step motor driver that has 200 steps per revolution is not proper. So we need micro step motor driver that is more precise then usual step motor driver. In this paper, micro step motor driver is used for precise control of step motor. The goal is precise operation and location control. This micro step motor driver is A3972SB that is made in Alloegro Company. It has serial port that receives two 6-bits linear DAC value. Almost all systems generate DAC value with micro processer and ...

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1923-1930
• /
• 2004

This paper presents digital microflow controllers(DMFC), where a fluidic digital-to-analog converter(DAC) is used to achieve high-linearity, fine-level flow control for applications to precision biomedical dosing systems. The fluidic DAC, composed of binary-weighted flow resistance, controls the flow-rate based on the ratio of the flow resistance to achieve high-precision flow-rate control. The binary-weighted flow resistance has been specified by a serial or a parallel connection of an identical flow resistor to improve the linearity of the flow-rate control, thereby making the flow-resistance ratio insensitive to the size uncertainty in flow resistors due to micromachining errors. We have designed and fabricated three different types of 4-digit DMFC: Prototype S and P are composed of the serial and the parallel combinations of an identical flow resistor, while Prototype V is based on the width-varied flow resistors. In the experimental study, we perform a static test for DMFC at the forward and backward flow conditions as well as a dynamic tests at pulsating flow conditions. The fabricated DMFC shows the nonlinearity of 5.0% and the flow-rate levels of 16(2$^{N}$) for the digital control of 4(N) valves. Among the 4-digit DMFC fabricated with micromachining errors, Prototypes S and P show 27.2% and 27.6% of the flow-rate deviation measured from Prototype V, respectively; thus verifying that Prototypes S and P are less sensitive to the micromachining error than Prototype V.V.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.11C
• /
• pp.1102-1110
• /
• 2007

In this paper, we design the FPGA (Field-Programmable Gate Array) of the CAMB (Constant-Amplitude Multi-code Biorthogonal) modulation, and implement the SoC (System on Chip). The ASIC (Application Specific Integrated Circuit) chip is be implemented through targeting and board test. This 12Mbps modem SoC includes the ARM (Advanced RISC Machine)7TDMI, 64Kbyte SRAM(Static Random Access Memory) and ADC (Analog to Digital Converter)/DAC (Digital to Analog Converter) for flexible applications. Additionally, the modem SoC can support the variable communication interfaces such as the 16-bits PCMCIA (Personal Computer Memory Card International Association), USB (Universal Serial Bus) 1.1, and 16C550 Compatible UART (Universal Asynchronous Receiver/Transmitter).

• The KIPS Transactions:PartA
• /
• v.15A no.6
• /
• pp.317-324
• /
• 2008

In this paper, we propose a system which easily controls the existing serially connected multi-channel speakers in a general personal computer by using a USB(Universal Serial Bus) interface. The personal computer as a host of the USB interface analyzes a sound source and sends audio data in a real-time fashion by the use of the isochronous transmission, one of four transmission methods provided by the USB interface. In addition, a channel is assigned by means of the bulk transmission, one of four transmission methods provided by the USB interface. Transmitted data from the USB host are sent to each speaker through compression and packet generation process. Each speaker detects corresponding digital data and regenerates audio signals through DAC(Digital-to-Analog Converter). A user can easily select a sound source file and a channel by the use of a GUI environment in a personal computer.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.2
• /
• pp.61-69
• /
• 2003

In this paper, we developed the U parameter test system which inspects the property of DC parameter for semiconductor products. The developed system is interfaced by IBM-PC. It is consisted of CPLD part, ADC (Analogue to Digital Converter), DAC (Digital to Analogue Converter), voltage/current source, variable resistor and measurement part. In the proposed system, we have designed the constant voltage source and the constant current source in a part. The CPLD part is designed by VHBL, which it generates the control and converts the serial data to parallel data. The proposed system has two test channels and it operates VFCS mode and CFVS mode. The range of test voltage is from 0[V] to 100[V], and the range of test current is from 0[mA] to 100[mA)]. The diode is tested. The test results have a good performance.