• Advances in nano research
• /
• 제2권1호
• /
• pp.1-14
• /
• 2014

Dislocations are basic crystal defects and represent one-dimensional native nanostructures embedded in a perfect crystalline matrix. Their structure is predefined by crystal symmetry. Two-dimensional, self-organized arrays of such nanostructures are realized reproducibly using specific preparation conditions (semiconductor wafer direct bonding). This technique allows separating dislocations up to a few hundred nanometers which enables electrical measurements of only a few, or, in the ideal case, of an individual dislocation. Electrical properties of dislocations in silicon were measured using MOSFETs as test structures. It is shown that an increase of the drain current results for nMOSFETs which is caused by a high concentration of electrons on dislocations in p-type material. The number of electrons on a dislocation is estimated from device simulations. This leads to the conclusion that metallic-like conduction exists along dislocations in this material caused by a one-dimensional carrier confinement. On the other hand, measurements of pMOSFETs prepared in n-type silicon proved the dominant transport of holes along dislocations. The experimentally measured increase of the drain current, however, is here not only caused by an higher hole concentration on these defects but also by an increasing hole mobility along dislocations. All the data proved for the first time the ambipolar behavior of dislocations in silicon. Dislocations in p-type Si form efficient one-dimensional channels for electrons, while dislocations in n-type material cause one-dimensional channels for holes.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 반도체재료
• /
• pp.38-41
• /
• 2001

In this work, we have been studied the characteristics of each nitride film for the optimization of PMD(pre-metal dielectric) liner nitride process, which can applicable in the recent semiconductor manufacturing process. The deposition conditions of nitride film were splited by PO (protect overcoat) nitride, baseline, low hydrogen, high stress and low hydrogen, respectively. And also we tried to catch hold of correlation between BPSG(boro-phospho silicate glass) deposition and densification. Especially, we used FTIR area method for the analysis of density change of Si-H bonding and Si-NH-Si bonding, which decides the characteristics of nitride film. To judge whether the deposited films were safe or not, we investigated the crack generation of wafer edge after BPSG densification, and the changes of nitride film stress as a function of RF power variation.

• ETRI Journal
• /
• 제17권4호
• /
• pp.1-12
• /
• 1996

A novel body-tied silicon-on-insulator(SOI) n-channel metal-oxide-semiconductor field-effect transistor with grounded body electrode named GBSOI nMOSFET has been developed by wafer bonding and etch-back technology. It has no floating body effect such as kink phenomena on the drain current curves, single-transistor latch and drain current overshoot inherent in a normal SOI device with floating body. We have characterized the interface trap density, kink phenomena on the drain current ($I_{DS}-V_{DS}$) curves, substrate resistance effect on the $I_{DS}-V_{DS}$ curves, subthreshold current characteristics and single transistor latch of these transistors. We have confirmed that the GBSOI structure is suitable for high-speed and low-voltage VLSI circuits.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제6권2호
• /
• pp.95-100
• /
• 2006

The GaAs-on-insulator (GOI) wafer fabrication technique has been developed by using ion-cut process, based on hydrogen ion implantation and wafer direct bonding techniques. The hydrogen ion implantation condition for the ion-cut process in GaAs and the associated implantation mechanism have been investigated in this paper. Depth distribution of hydrogen atoms and the corresponding lattice disorder in (100) GaAs wafers produced by 40 keV hydrogen ion implantation were studied by SIMS and RBS/channeling analysis, respectively. In addition, the formation of platelets in the as-implanted GaAs and their microscopic evolution with annealing in the damaged layer was also studied by cross-sectional TEM analysis. The influence of the ion fluence, the implantation temperature and subsequent annealing on blistering and/or flaking was studied, and the optimum conditions for achieving blistering/splitting only after post-implantation annealing were determined. It was found that the new optimum implant temperature window for the GaAs ion-cut lie in $120{\sim}160^{\circ}C$, which is markedly lower than the previously reported window probably due to the inaccuracy in temperature measurement in most of the other implanters.

• 반도체디스플레이기술학회지
• /
• 제17권4호
• /
• pp.42-45
• /
• 2018

As The semiconductor decrease from 10 nanometer to 7 nanometer, It is suggested that "More than Moore" is needed to follow Moore's Law, which has been a guide for the semiconductor industry. Fan-Out Wafer Level Package(FOWLP) is considered as the key to "More than Moore" to lead the next generation in semiconductors, and the reasons are as follows. the fan-out WLP does not require a substrate, unlike conventional wire bonding and flip-chip bonding packages. As a result, the thickness of the package reduces, and the interconnection becomes shorter. It is easy to increase the number of I / Os and apply it to the multi-layered 3D package. However, FOWLP has many issues that need to be resolved in order for mass production to become feasible. One of the most critical problem is the warpage problem in a process. Due to the nature of the FOWLP structure, the RDL is wired to multiple layers. The warpage problem arises when a new RDL layer is created. It occurs because the solder ball reflow process is exposed to high temperatures for long periods of time, which may cause cracks inside the package. For this reason, we have studied warpage in the FOWLP structure using commercial simulation software through the implementation of the reflow process. Simulation was performed to reproduce the experiment of products of molding compound company. Young's modulus and poisson's ratio were found to be influenced by the order of influence of the factors affecting the distortion. We confirmed that the lower young's modulus and poisson's ratio, the lower warpage.

• 마이크로전자및패키징학회지
• /
• 제23권3호
• /
• pp.1-6
• /
• 2016

IoT 적용을 위해서는 다종 소자를 높은 connectivity 밀도로 집적화시키는 전자패키징 기술이 매우 중요하다. FOWLP 기술은 입출력 밀도가 높고, 소자의 집적화가 우수하고, 디자인 유연성이 우수하여, 최근 개발이 집중되고 있는 기술이다. 웨이퍼나 패널 기반의 FOWLP 기술은 초미세 피치 RDL 공정 기술과 몰딩 기술 개발이 최적화 되어야 할 것이다. 3D stacking 기술 특히 웨이퍼 본딩 후 TSV를 제조하는 방법(via after bonding)은 가격을 낮추면서 connectivity를 높이는데 매우 효과적이라 하겠다. 하지만 저온 웨이퍼 본딩이나 TSV etch stop 공정과 같이 아직 해결해야할 단위 공정들이 있다. Substrate 기술은 두께를 줄이고 가격을 낮추는 공정 개발이 계속 주목되겠지만, 칩과 PCB와의 통합설계(co-design)가 더욱 중요하게 될 것이다.

• 마이크로전자및패키징학회지
• /
• 제28권3호
• /
• pp.9-15
• /
• 2021

최근 반도체 소자의 소형화는 물리적 한계에 봉착했으며, 이를 극복하기 위한 방법 중 하나로 반도체 소자를 수직으로 쌓는 3D 패키징이 활발하게 개발되었다. 3D 패키징은 TSV, 웨이퍼 연삭, 본딩의 단위공정이 필요하며, 성능향상과 미세피치를 위해서 구리 본딩이 매우 중요하게 대두되고 있다. 본 연구에서는 대기중에서의 구리 표면의 산화방지와 저온 구리 본딩에 티타늄 나노 박막이 미치는 영향을 조사하였다. 상온과 200℃ 사이의 낮은 온도 범위에서 티타늄이 구리로 확산되는 속도가 구리가 티타늄으로 확산되는 속도보다 빠르게 나타났고, 이는 티타늄 나노 박막이 저온 구리 본딩에 효과적임을 보여준다. 12 nm 티타늄 박막은 구리 표면 위에 균일하게 증착되었고, 표면거칠기(R_q)를 4.1 nm에서 3.2 nm로 낮추었다. 티타늄 나노 박막을 이용한 구리 본딩은 200℃에서 1 시간 동안 진행하였고, 이후 동일한 온도와 시간 동안 열처리를 하였다. 본딩 이후 측정된 평균 전단강도는 13.2 MPa이었다.

• Journal of Welding and Joining
• /
• 제32권3호
• /
• pp.11-18
• /
• 2014

TSV(through silicon via) filling technology is making a hole in Si wafer and electrically connecting technique between front and back of Si die by filling with conductive metal. This technology allows that a three-dimensionally connected Si die can make without a large number of wire-bonding. These TSV technologies require various engineering skills such as forming a via hole, forming a functional thin film, filling a conductive metal, polishing a wafer, chip stacking and TSV reliability analysis. This paper addresses the TSV filling using Cu electrodeposition. The impact of plating conditions with additives and current density on electrodeposition will be considered. There are additives such as accelerator, inhibitor, leveler, etc. suitably controlling the amount of the additive is important. Also, in order to fill conductive material in whole TSV hole, current wave forms such as PR(pulse reverse), PPR(periodic pulse reverse) are used. This study about semiconductor packaging will be able to contribute to the commercialization of 3D TSV technology.

• 제어로봇시스템학회논문지
• /
• 제21권12호
• /
• pp.1115-1121
• /
• 2015

Fast inspection of solder ball bumps in ball grid array (BGA) is an important issue in the flip chip bonding technology. Particularly, semiconductor industry has required faster and more accurate inspection of micron-size solder bumps in flip chip bonding, as the density of balls increase dramatically. In this paper, we describe an inspection approach of BGA balls by using 5-step ring illumination device and normalized cross-correlation (NCC) method. The images of BGA ball by the illumination device show unique and distinguishable characteristic contours by their 3-D shapes, which are called as "iso-slope contours". Template images of reference ball samples can be produced artificially by the hybrid reflectance model and 3D data of balls. NCC values between test and template samples are very robust and reliable under well-structured condition. The 200 samples on real wafer are tested and show good practical feasibility of the proposed method.

• Korean Chemical Engineering Research
• /
• 제47권1호
• /
• pp.1-10
• /
• 2009

작은 크기의 고기능성 휴대용 전자기기 수요의 급증에 따라 기존에 사용되던 수평구조의 2차원 칩의 크기를 줄이는 것은, 전기 배선의 신호지연 증가로 한계에 도달했다. 이러한 문제를 해결하기 위해 칩들을 수직으로 적층한 뒤, 수평 구조의 긴 신호배선을 짧은 수직 배선으로 만들어 신호지연을 최소화하는 3차원 칩 적층기술이 새롭게 제안되었다. 3차원 칩의 개발을 위해서는 기존에 사용되던 반도체 공정들뿐 아니라 실리콘 관통 전극 기술, 웨이퍼 박화 기술, 웨이퍼 정렬 및 본딩 기술 등의 새로운 공정들이 개발되어야 하며 위 기술들의 표준 공정을 개발하기 위한 노력이 현재 활발히 진행되고 있다. 현재까지 4~8개의 단일칩을 수직으로 적층한 DRAM/NAND 칩, 및 메모리 칩과 CPU 칩을 한꺼번에 적층한 구조의 성공적인 개발 결과가 보고되었다. 본 총설에서는 이러한 3차원 칩 적층의 기본 원리와 구조, 적층에 필요한 중요 기술들에 대한 소개, 개발 현황 및 앞으로 나아갈 방향에 대해 논의하고자 한다.