• Proceedings of the KAIS Fall Conference
• /
• 2004.11a
• /
• pp.195-198
• /
• 2004

실리콘 산화막 위에 구리 확산 방지막으로서 W-N 박막을 $NH_3$ 펄스 플라즈마를 이용한 원자층 증착방법으로 형성하였다. 플라즈마 원자층 증착방법 (PPALD)은 일반적인 원자층 증착방법(ALD)의 성장 기구를 그대로 따라 간다. 그러나 일반적인 ALD 방법에 의해 증착한 W-N 박막에 비해 PPALD 방법으로 증착한 W-N 박막은 F 함유량과 비저항이 감소하였고 열적 안정성에 대한 특성도 향상되었다. 또한 $WF_6$ 가스는 실리콘 산화막과 반응을 하지 않기 때문에 $WF_6$ 가스와 $NH_3$ 가스를 사용해서 ALD 증착방법으로 실리콘 산화막 위에 W-N 박막을 증착하기 어려운 문제점(8,9)을 $NH_3$ 반응종으로 실리콘 산화막 표면을 먼저 변형시켜 $WF_6$ 가스가 산화막과 반응을 할 수 있게 함으로써 ALD 방법으로 W-N 박막을 실리콘 산화막 위에 증착 할 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.116-119
• /
• 1994

The characteristics of the Si-SiO$_2$ interface and the degradation in the short channel(L${\times}$W=1.7$\mu\textrm{m}$${\times}$15$\mu\textrm{m}$) SONOSFET nonvolatile memory devices, fabricated on the basis of the existing n-well CMOS processing technology for 1 Mbit DRAM with the 1.2$\mu\textrm{m}$ m design rule, were investigated using the charge pumping method. The SONOSFET memories have the tripple insulated-gate consisting of 30${\AA}$ tunneling oxide 205${\AA}$ nitride and 65${\AA}$ blocking oxide, The acceleration method which square voltage pulses of t$\_$p/=10msec, Vw=+19V and V$\_$E/=-22V continue to be alternatly applied to gale, was used to investigate the degradation of SONOSFET memories with the write/erase cycle. The degradation characteristics were ascertained by observing the change in the energy and spatial distributions of the interface trap density.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1091-1098
• /
• 1998

Thermal stability of the electroless deposited Cu thin film was investigated. Cu/TaN/Si multilayer was fabricated by electroless-depositing Cu thin layer on TaN diffusion barrier layer which was deposited by MOCVD on the Si substrate, and was annealed in $H_2$ ambient to investigate the microstructure of Cu film with a post heat-treatment. Cu thin film with good adhesion was successfully deposited on the surface of the TaN film by electroless deposition with a proper activation treatment and solution control. Microstructural property of the electroless-deposited Cu layer was improved by a post-annealing in the reduced atmosphere of $H_2$ gas up to $600^{\circ}C$. Thermal stability of Cu/TaN/Si system was maintained up to $600^{\circ}C$ annealing temperature, but the intermediate compounds of Cu-Si were formed above $650^{\circ}C$ because Cu element passed through the TaN layer. On the other hand, thermal stability of the Cu/TaN/Si system in Ar ambient was maintained below $550^{\circ}C$ annealing temperature due to the minimal impurity of $O_2$ in Ar gas.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2006.10a
• /
• pp.4-5
• /
• 2006

This paper represents modeling and optimization techniques for solar cell process on single-crystalline float zone (FZ) wafers with high efficiency; There were the four significant processes : i)emitter formation by diffusion, anti-reflection-coating (ARC) with silicon nitride using plasma-enhanced chemical vapor deposition (PECVD); iii)screen-printing for front and back metallization; and iv)contact formation by firing. In order to increase the performance of solar cells, the contact formation process is modeled and optimized. This paper utilizes the design of experiments (DOE) in contact formation to reduce process time, fabrication costs. The experiments were designed by using central composite design which is composed of $2^4$ factorial design augmented by 8 axial points with three center points. After contact formation process, the efficiency of the solar cell is modeled using neural networks. This model is used to analyse the characteristics of the process, and to optimize the process condition using genetic algorithms (GA). Finally, find optimal recipe for solar cell efficiency.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.6
• /
• pp.342-349
• /
• 2019

Titanium nitride(TiN) thin films have been deposited on PEN(Polyethylene naphthalate) substrate by reactive RF(13.56 MHz) magnetron sputtering in a 25% N₂/Ar mixed gas atmosphere. The pulsed DC bias voltage of -50V on substrates was applied with a frequency of 350 kHz, and duty ratio of 40%(1.1 ㎲). The effects of pulsed DC substrate bias voltage on the crystallinity, color, electrical properties of TiN_x films have been investigated using XRD, SEM, XPS and measurement of the electrical properties such as electrical conductivity, carrier concentration, mobility. The deposition rates of TiN_x films was decreased with application of the pulsed DC substrate bias voltage. The TiN_x films deposited without and with pulsed bias of -50V to substrate exhibits gray and gold colors, respectively. XPS depth profiling revealed that the introduction of the substrate bias voltage resulted in decreasing oxygen concentration in TiN_x films, and increasing the electrical conductivities, carrier concentration, and mobility to about 10 times, 5 times, and 2 times degree, respectively.

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.706-712
• /
• 1997

AlN(Aluminium Nitride) thin films were prepared using by RF sputtering method on the Si(100) and Si(111) substrates as the parameters of the substrate temperature, RF power, sputtering duration and the $N_2$/Ar ratio and investigated by X-ray diffraction, IR spectrometry, n&k analyzer. For the Si(100) substrate, the AlN thin films of (101) orientation were obtained under the conditions of room temperature and the nitrogen of 60 vol.%. For the Si(111) substrate, the (002) AlN thin films were obtained under the nitrogen of 100 vol.%. In case of the thin film prepared in the condition of above 60 vol.% of the nitrogen, the average value of the surface roughness of the film was 151$\AA$. From the changes of the half widths of E$_1$[TO] phonon bands at the wavenumber of 680$cm^{-1}$ /, it were compared of the crystallinities of the films which were grown under the different conditions. The thicknesses of AlN films were decreased dramatically in the region of the nitrogen of 40~60 vol.%. Its due to the nitridation of the Al target surface and getting low of the sputtering yield by the $N_2$/Ar ratio being increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.149-153
• /
• 2003

Chemical mechanical polishing (CMP) technology for global planarization of multi-level inter-connection structure has been widely studied for the next generation devices. CMP process has been paid attention to planarized pre-metal dielectric (PMD), inter-layer dielectric (ILD) interconnections. Expecially, shallow trench isolation (STI) used to CMP process on essential. Recently, the direct STI-CMP process without the conventional complex reverse moat etch process has established by using slurry additive with the high selectivity between $SiO_2$ and $Si_3N_4$ films for the purpose of process simplification and n-situ end point detection(EPD). However, STI-CMP process has various defects such as nitride residue, tom oxide and damage of silicon active region. To solve these problems, in this paper, we studied the planarization characteristics using a high selectivity slurry(HSS). As our experimental results, it was possible to achieve a global planarization and STI-CMP process could be dramatically simplified. Also we estimated the reliability through the repeated tests with the optimized process conditions in order to identify the reproducibility of HSS STI-CMP process.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1884-1886
• /
• 2005

KrF 펄스 레이저 증착법(pulsed laser deposition: PLD)으로 ZnO 박막을 증착하여 평판 디스플레이 소자 구동용 박막 트랜지스터(thin film transistor) 소자를 제작하였다. 전도성이 높은 실리콘웨이퍼(c-Si, 하부전극) 기판 위에 LPCVD 법으로 silicon nitride 박막을 절연막으로 형성하고, 다양한 공정 조건에서 펄스 레이저 증착법으로 제작한 ZnO 박막을 증착하여 채널층으로 하였으며, Al 박막을 증착하고 패터닝하여 소스 및 드레인 전극으로 하였다. ZnO 박막의 증착 시에 기판 온도를 다양하게 조절하고 산소 분압을 변화시켜 ZnO 박막의 특성을 조절하였다. 제작된 박막의 표면특성은 AFM(atomic force microscopy)로 분석하고, 결정특성은 XRD(X-ray diffraction)로 조사하였다. ZnO 박막의 전기적 특성은 Hall-van der Pauw 법으로 측정하였고, 광학 투과도(optical transparency)를 UV-visible photometer로 조사하였다. ZnO-TFT 소자는 $10^6$ 수준의 on-off ratio와 $2.4{\sim}6.1cm^2/V{\cdot}s$의 전계효과이동도(field effect mobility)를 보였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.6
• /
• pp.370-375
• /
• 2016

In this paper, we investigated the electrical properties of crystalline silicon solar cell fabricated with Ni/Cu/Ag plating. The laser process was used to ablate silicon nitride layer as well as to form the selective emitter. Phosphoric acid layer was spin-coated to prevent damage caused by laser and formed selective emitter during laser process. As a result, the contact resistance was decreased by lower sheet resistance in electrode region. Low sheet resistance was obtained by increasing laser current, but efficiency and open circuit voltage were decreased by damage on the wafer surface. KOH treatment was used to remove the laser damage on the silicon surface prior to metalization of the front electrode by Ni/Cu/Ag plating. Ni and Cu were plated for each 4 minutes and 16 minutes and very thin layer of Ag with $1{\mu}m$ thickness was plated onto Ni/Cu electrode for 30 seconds to prevent oxidation of the electrode. The silicon solar cells with KOH treatment showed the 0.2% improved efficiency compared to those without treatment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.8
• /
• pp.514-519
• /
• 2017

TiN (titanium nitride) films were prepared using the RF magnetron sputtering technique. The films were deposited by pure $N_2$ plasma sputtering. Their mechanical properties, such as nano-indentation hardness, friction coefficient, and surface wettability, have been investigated. X-ray diffraction (XRD) studies revealed that the orientation of $TiN_X$ films changed towards the (111) orientation with decreasing working pressure due to a strong compressive stress during deposition. The strongest TiN (111) orientation was found when the film was deposited at a working pressure of 1 Pa. This film showed the largest hardness (16 GPa) and smallest friction coefficient (0.17) among the studied samples. Moreover, this film was found to be accompanied by a water-repellent surface with water contact angle more than $100^{\circ}$.