• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.89-96
• /
• 2003

Photoluminescence (PL) and photoluminescence excitation (PLE) spectroscopy have been performed at 6 K on the 1540 nm $^4$I$\_$(13/2)/\longrightarrow$^4$I$\_$(15/2)/ emission of Er$\^$+3/ in in situ Er-doped GaN The PL and PLE spectra of in situ Er-doped GaN are compared with those of Er-implanted GaN in this study. The lineshapes of the broad PLE absorption bands and the broad PL bands in the spectra of the in situ Er-doped GaN are similar to those in Er-doped glass rather than in the Er-implanted GaN. The PL spectra of this in situ Er-doped GaN are independent of excitation wavelength and their features are significantly different from the site-selective PL spectra of the Er-implanted GaN. These PL and PLE studies reveal that a single type of Er$\^$3+/ sites is present in the in situ Er-doped GaN and these Er sites are different from those observed in the Er-implanted GaN. In addition, the comparison of the PL single strength illustrates that the excitation of Er$\^$3+/ sites through the energy absorption of defects in Er-implanted GaN.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.107-116
• /
• 1994

In this paper, The electrical properties of MOS capacitors and transistoras with gate of in-situ doped amorphous Si and poly Si doped by POCI$_3$. Under constant current F-N stress, MOS capacitors with in-situ doped amorphous Si gate have shown the best resistance to degradation in reliabilty properties such as increase of leakage current, shift of gate voltage (V$_{g}$). shift of flat band voltage (V$_{fb}$) and charge to breakdown(Q$_{bd}$). Also, MOSFETs with in-situ doped amorphous Si gate have shown to have less degradation in transistor properties such as threshold voltage, transconductance and drain current. These improvements observed in MOS devices with in-situ doped amorphous Si gate is attributed to less local thinning spots at the gate/SiO$_2$ interface, caused by the large grain size and the smoothness of the surface at the gate/SiO$_2$ interface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.2
• /
• pp.125-130
• /
• 2000

Two step growth of reduced pressure chemical vapor eposition has been successfully developed to achieve in-situ phosphorus-doped silicon epilayers, and the characteristic evolution on their microstructures has been investigated using scanning electron microscopy, transmission electron microscopy, and secondary ion mass spectroscopy. The two step growth, which employs heavily in-situ P doped silicon buffer layer grown at low temperature, proposes crucial advantages in manipulating crystal structures of in-situ phosphorus doped silicon. In particular, our experimental results showed that with annealing of the heavily P doped silicon buffer layers, high-quality epitaxial silicon layers grew on it. the heavily doped phosphorus in buffer layers introduces into native oxide and plays an important role in promoting the dispersion of native oxides. Furthermore, the phosphorus doping concentration remains uniform depth distribution in high quality single crystalline Si films obtained by the two step growth.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.2
• /
• pp.95-100
• /
• 2000

For the well-controlled growing in-situ heavily phosphorus doped polycrystalline Si films directly on Si wafer by reduced pressure chemical vapor deposition, a study is made of the two step growth. When in-situ heavily phosphorus doped Si films were deposited directly on Si (100) wafer, crystal structure in the film is not unique, that is, the single crystal to polycrystalline phase transition occurs at a certain thickness. However, the well-controlled polycrtstalline Si films deposited by two step growth grew directly on Si wafers. Moreover, the two step growth, which employs crystallization of grew directly on Si wafers. Moreover, the two step growth which employs crystallization of amorphous silicon layer grown at low temperature, reveals crucial advantages in manipulating polycrystal structures of in-situ phosphorous doped silicon.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.208-212
• /
• 2008

This paper reports physical properties of in situ boron doped silicon films made from boron source gas and silane ($SiH_4$) gas in a conventional low-pressure chemical vapor deposition vertical furnace. If the p-type polysilicon is formed by boron implantation into undoped polysilicon, the plasma nitridation (PN) process is added on the oxide in order to suppress boron penetration that can be caused during the thermal treatments used in fabrication. In-situ boron doped polysilicon deposition can complete p-type polysilicon film with only one deposition process and need not the PN process, because there is not interdiffusion of dopant at the intermediate temperatures of the subsequent steps. Since in-situ boron doped polysilicon films have higher work function than that of n-type polysilicon and they are compatible with the underlying oxide, they may be promising materials for improving memory cell characteristics if we make its profit of these physical properties.

• Progress in Superconductivity
• /
• v.10 no.2
• /
• pp.79-86
• /
• 2009

We successfully fabricated C-doped ex-situ $MgB_2$ wires using two different methods such as mechanical alloying(MA) and combined process(CP) of in-situ and ex-situ. In the MA, the precursor powder was prepared with a mixture of $MgB_2$ and 1 at% C powders by planetary ball milling for 0-100 h. In the CP, on the other hand, C-doped $MgB_2$ powder was prepared with Mg, B, and C powders by in-situ process via compaction, sintering, and crushing. The powders prepared by two methods were loaded into Fe tube and then the assemblages were drawn by a conventional powder-in-tube technique. The MA treatment of C-added $MgB_2$ decreased the particles/grains size and resulted in C-doping into $MgB_2$ after sintering, improving the critical current density($J_c$) in high external magnetic field. For the C-doped $MgB_2$ wire by MA for 25 h, the $J_c$ was $4.1{\times}10^3A/cm^2$ at 5 K and 6.4 T, which was 5.9 times higher than that of pure and untreated $MgB_2$ wire. The CP also provided C-doping into $MgB_2$ and improved the $J_c$ in high magnetic field; the C-doped $MgB_2$ wire fabricated by CP exhibited a $J_c$ being 2.3 times higher than that of the ex-situ wire used commercial $MgB_2$ powder at 5 K and 6.0 T($2.7{\times}10^3A/cm^2\;vs.\;1.2{\times}10^3A/cm^2$).

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.128-129
• /
• 1994

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.487-490
• /
• 2010

This paper describes the elecrtical and optical characteristics of $N_2$ doped porous 3C-SiC films. Polycrystalline 3C-SiC thin films are anodized by $HF+C_2H_5OH$ solution with UV-LED exposure. The growth of in-situ doped 3C-SiC thin films on p-type Si (100) wafers is carried out by using APCVD (atmospheric pressure chemical vapor deposition) with a single-precursor of HMDS (hexamethyildisilane: $Si_2(CH_3)_6)$. 0 ~ 40 sccm $N_2$ was used for doping. After the growth of doped 3C-SiC, porous 3C-SiC is formed by anodization with $7.1\;mA/cm^2$ current density for anodization time of 60 sec. The average pore diameter is about 30 nm, and etched area is increased with $N_2$ doping rate. These results are attributed to the decrease of crystallinity by $N_2$ doping. Mobility is dramatically decreased in porous 3C-SiC. The band gaps of polycrystalline 3C-SiC films and doped porous 3C-SiC are 2.5 eV and 2.7 eV, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.235-238
• /
• 2009

This paper describes the mechanical properties of poly (Polycrystalline) 3C-SiC thin films with $N_2$ in-situ doping. In this work, the poly 3C-SiC film was deposited by APCVD (Atmospheric Pressure Chemical Vapor Deposition) method using single-precursor HMDS (Hexamethyildisilane: $Si_2(CH_3)_6)$ at $1200^{\circ}C$. The mechanical properties of doped poly 3C-SiC thin films were measured by nono-indentation according to the various $N_2$ flow rate. In the case of 0 sccm $N_2$ flow rate, Young's Modulus and hardness were obtained as 285 GPa and 35 GPa, respectively. Young's Modulus and hardness were decreased according to increase of $N_2$ flow rate. The crystallinity and surface roughness was also measured by XRD (X-Ray Diffraction) and AFM (Atomic Force Microscopy), respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.18-19
• /
• 2008

Polycrystalline(poly) 3C-SiC film is a promising structural material for M/NEMS used in harsh environments, bio and fields. In order to realize poly 3C-SiC based M/NEMS devices, the electrical properties of poly 3C-SiC film have to be optimized. The n-type poly 3C-SiC thin film is deposited by APCVD using HMDS$(Si_2(CH_3)_6)$ as single precursor and are in-situ doped using N2. Resistivity values as low as 0.014 $\Omega$cm were achieved. The carrier concentration increased with doping from $3.0819\times10^{17}$ to $2.2994\times10^{19}cm^{-3}$ and electronicmobility increased from 2.433 to 29.299 $cm^2/V{\cdot}s$.