• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1391-1392
• /
• 1997

The thin films of $\alpha$-Sexithiophene($\alpha$-6T) were deposited by Organic Molecular Beam Deposition(OMBD) technique. The $\alpha$-6T was synthesized and Purified by the sublimation method The thin films of the $\alpha$-6T were deposited under various deposition conditions. The effects of deposition rate substrate temperature, and vacuum pressure on the formation of these films have been studied. The molecular orientations of $\alpha$-6T films were investigated with the polarized electronic absorption spectroscopy. The molecules in the $\alpha$-6T film deposited at a low deposition rate under a high vacuum were almost aligned Perpendicular to the substrate. The film deposited at an elevated substrate temperature(${\sim}90^{\circ}C$) showed higher conductivity than deposited at room temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.264-264
• /
• 2010

Single-walled carbon nanotubes (SWCNTs) were grown on a Si wafer by using thermal chemical vapor deposition (t-CVD). We investigated the effect of the catalyst deposition rate on the types of CNTs grown on the substrate. In general, smaller islands of catalyst occur by agglomeration of a catalyst layer upon annealing as the catalyst layer becomes thinner, which results in the growth of CNTs with smaller diameters. For the same thickness of catalyst, a slower deposition rate will cause a more uniformly thin catalyst layer, which will be agglomerated during annealing, producing smaller catalyst islands. Thus, we can expect that the smaller-diameter CNTs will grow on the catalyst deposited with a lower rate even for the same thickness of catalyst. The 0.5-nm-thick Fe served as a catalyst, underneath which Al was coated as a catalyst support as well as a diffusion barrier on the Si substrate. The catalyst layers were. coated by using thermal evaporation. The deposition rates of the Al and Fe layers varied to be 90, 180 sec/nm and 70, 140 sec/nm, respectively. We prepared the four different combinations of the deposition rates of the AI and Fe layers. CNTs were synthesized for 10 min by flowing 60 sccm of Ar and 60 sccm of $H_2$ as a carrier gas and 20 sccm of $C_2H_2$ as a feedstock at 95 torr and $810^{\circ}C$. The substrates were subject to annealing for 20 sec for every case to form small catalyst islands prior to CNT growth. As-grown CNTs were characterized by using field emission scanning electron microscopy, high resolution transmission electron microscopy, Raman spectroscopy, UV-Vis NIR spectroscopy, and atomic force microscopy. The fast deposition of both the Al and Fe layers gave rise to the growth of thin multiwalled CNTs with the height of ${\sim}680\;{\mu}m$ for 10 min while the slow deposition caused the growth of ${\sim}800\;{\mu}m$ high SWCNTs. Several radial breathing mode (RBM) peaks in the Raman spectra were observed at the Raman shifts of $113.3{\sim}281.3\;cm^{-1}$, implying the presence of SWCNTs (or double-walled CNTs) with the tube diameters 2.07~0.83 nm. The Raman spectra of the as-grown SWCNTs showed very low G/D peak intensity ratios, indicating their low defect concentrations.

• 한국산학기술학회논문지
• /
• 제18권7호
• /
• pp.17-25
• /
• 2017

최근에 LED나 OLED와 같은 조명용 소자의 온도 상승에 따른 문제점을 개선하기 위하여 전기 도금 방법을 사용하여 제작한 두께가 두꺼운 금속 필름을 heat sink로 사용하고 있다. Cu 필름과 같은 두꺼운 금속 필름은 습식 방법인 전기 도금으로 제작하여 주로 소자의 방열판으로 사용되어 왔으나 건식의 증착 방법을 이용한 수 백 ${\mu}m$의 Cu 금속 필름에 대한 필요성이 요구되고 있다. 본 연구에서 설계 제작된 유도 가열 방식의 Cu 필름 증착 장비는 가열부가 세라믹 도가니 히터 부분과 세라믹 도가니 부분으로 분리된 이중 구조의 heating 방식을 채택하여 열 손실을 최소화 하고 보온 효과를 극대화시켰다. 또한 유도 가열 방식으로 초고속의 필름 증착 속도를 구현하였다. 그리고 열전도도가 높고 안정적인 두꺼운 Cu 필름 증착기술을 확보하고 최적화 하여 $1000{\AA}/s$의 증착율로 $100{\mu}m$의 필름을 증착 하였으며 ~2.0% 이내의 두께 균일도를 얻었다.

• Carbon letters
• /
• 제28권
• /
• pp.72-80
• /
• 2018

In this study, an empirical relationship between the energy band gap of multi-walled carbon nanotubes (MWCNTs) and synthesis parameters in a chemical vapor deposition (CVD) reactor using factorial design of experiment was established. A bimetallic (Fe-Ni) catalyst supported on $CaCO_3$ was synthesized via wet impregnation technique and used for MWCNT growth. The effects of synthesis parameters such as temperature, time, acetylene flow rate, and argon carrier gas flow rate on the MWCNTs energy gap, yield, and aspect ratio were investigated. The as-prepared supported bimetallic catalyst and the MWCNTs were characterized for their morphologies, microstructures, elemental composition, thermal profiles and surface areas by high-resolution scanning electron microscope, high resolution transmission electron microscope, energy dispersive X-ray spectroscopy, thermal gravimetry analysis and Brunauer-Emmett-Teller. A regression model was developed to establish the relationship between band gap energy, MWCNTs yield and aspect ratio. The results revealed that the optimum conditions to obtain high yield and quality MWCNTs of 159.9% were: temperature ($700^{\circ}C$), time (55 min), argon flow rate ($230.37mL\;min^{-1}$) and acetylene flow rate ($150mL\;min^{-1}$) respectively. The developed regression models demonstrated that the estimated values for the three response variables; energy gap, yield and aspect ratio, were 0.246 eV, 557.64 and 0.82. The regression models showed that the energy band gap, yield, and aspect ratio of the MWCNTs were largely influenced by the synthesis parameters and can be controlled in a CVD reactor.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.67-70
• /
• 1999

We have fabricated YBa$_2Cu_3O_{7-x}$ thin films by cylindrical hollow cathode sputtering. For 2 inch diameter of MgO (100) substrate, we obtained the zero resistance temperature in the range from 83 K to 86 K and thickness uniformity better than 5 % over the whole area. Also, the average deposition rate was 100nm/h which is higher than 10 times compare to conventional off-axis sputtering method. These results indicate that cylindrical hollow cathode sputtering seems to have unique capabilities for high rate and homogeneous deposition of large area thin film.

• 한국진공학회지
• /
• 제1권1호
• /
• pp.153-161
• /
• 1992

A plasma has been used in a high vaccum, cold wall reactor for low temperature deposition of C54 TiSi2 and for in-situ surface cleaning prior to silicide deposition. SiH4 and TiCl4 were used as the silicon and titanium sources, respectively. The deposited films had low resistivities in the range of 15~25 uohm-cm. The investigation of the experimental variables' effects on the growth of silicide and its concomitant silicon consumption revealed that and were the dominant species for silicide formation and the primary factors in silicon consumption were gas composition ratio and temperature. Increasing silane flow rate from 6 to 9 sccm decreased silicon consumption from 1500 A/min to less than 30 A/min. Furthermore, decreasing the temperature from 650 to $590^{\circ}C$ achieved blanket silicide deposition with no silicon consumption. A kinetic model of silicon consumption is proposed to understand the fundamental mechanism responsible for the dependence of silicon consumption on SiH4 flow rate.

• 한국자기학회지
• /
• 제8권5호
• /
• pp.282-287
• /
• 1998

유리 기판위에 dc magnetron sputtering 방법으로 제작한Fe(50 $\AA$)/[Co(17 $\AA$)/Cu(24 $\AA$)]20 다층박막에 관하여 자기저항비의 기저층, 자성층, 비자성층의 증착률 및 열처리 의존성을 살펴보았다. 낮은 base 압력 중에서의 막의 증착은 Co/Cu 계면의 산화를 억제하여 자기저항비를 장가시켰다. 극대 자기저항비를 얻기위해 요구되는 증착률은 Fe는 1$\AA$)/s 이상, Cu는 2.8 $\AA$)/s 이었으며 Co는 증착률이 2 $\AA$/s 보다 높은 경우에 평탄한 자구형성을 이루어 자기적 향비가 높아지는 경향을 보였다. 40$0^{\circ}C$까지의 시료에 대한 역처리는 다층박막의 주기성을 유지한채 더 큰 결정립을 형성시켜 반강자성적으로 결합한 막의 부분이 증가함으로써 자기저항비를 증가시켰다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.236-236
• /
• 2011

Silicon oxynitride (SiON) was deposited for gas barrier film on polyethylene terephthalate (PET) using octamethylycyclodisiloxane (Si4O4C8H24, OMCTS) precursor by plasma enhanced chemical vapor deposition (PECVD) at low temperature. The ion flux and substrate temperature were measured by oscilloscope and thermometer. The chemical bonding structure and barrier property of films were characterized by Fourier transform infrared (FT-IR) spectroscopy and the water vapor transmission rate (WVTR), respectively. The deposition rate of films increases with RF bias and nitrogen dilution due to increase of dissociated precursor and nitrogen ion incident to the substrate. In addition, we confirmed that the increase of nitrogen dilution and RF bias reduced WVTR of films. Because, on the basis of FT-IR analysis, the increase of the nitrogen gas flow rate and RF bias caused the increase of the C=N stretching vibration resulting in the decrease of macro and nano defects.

• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.608-613
• /
• 2000

The present study has proposed a novel aerosol CVD utilizing an internal jet in the conventional MCVD reactor for the purpose of enhancing the deposition efficiency(and rate) and the uniformity of deposited film. The use of impingement of high temperature jet through a thin inner tube ensures the reduction of non-uniform particle deposition zone as well as higher thermophoretic particle deposition. It is shown that significant improvements have been achieved for both aspects of deposition efficiency and uniformity. As jet temperatures increase, the tapered length is reduced and deposition efficiency is significantly increased.

• Transactions on Electrical and Electronic Materials
• /
• 제6권1호
• /
• pp.14-17
• /
• 2005

The SrRuO_{3}$ films for application of the bottom electrode were deposited on p-Si (001) substrates by metalorganic chemical vapor deposition (MOCVD). The films are characterized by various deposition parameters. The optimum deposition condition for SRO films is the deposition temperature of $500{\circ}C$, Sr/Ru input mol ratio of 1.0, and a flow rate of precursors of 15 ml/h. The films deposited by an optimum condition exhibited a single phase of SrRuO_{3}$, an rms roughness of 8 nm, and a resistivity of approximately $900{\mu}{\Omega}{\cdot}cm$. The high resistivity of the films for application of a bottom electrode should be improved through a characterization of an interface.