• 전자공학회논문지 IE
• /
• v.47 no.1
• /
• pp.1-5
• /
• 2010

This paper presents new results of the impact of gate structure on hot-carrier-induced performance degradation in SOI low noise amplifier. Circuit simulations were carried out using the measured S-parameters of H--gate and T-gate SOI MOSFETs and Agilent's Advanced Design System (ADS) to compare the performance of H-gate LNA and T-gate LNA before and after stress. We will discuss the figure of merit for the characterization of low noise amplifier in terms of impedance matching (S11), noise figure, and gain as well as the relation between device degradation and performance degradation of LNA.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.4
• /
• pp.281-285
• /
• 2020

Oxide semiconductor devices have become increasingly important because of their high mobility and good uniformity. The channel length of oxide semiconductor thin film transistors (TFTs) also shrinks as the display resolution increases. It is well known that reducing the channel length of a TFT is detrimental to the current saturation because of drain-induced barrier lowering, as well as the movement of the pinch-off point. In an organic light-emitting diode (OLED), the lack of current saturation in the driving TFT creates a major problem in the control of OLED current. To obtain improved current saturation in short channels, we fabricated indium gallium zinc oxide (IGZO) TFTs with single gate and double gate structures, and evaluated the electrical characteristics of both devices. For the double gate structure, we connected the bottom gate electrode to the source electrode, so that the electric potential of the bottom gate was fixed to that of the source. We denote the double gate structure with the bottom gate fixed at the source potential as the BGFP (bottom gate with fixed potential) structure. For the BGFP TFT, the current saturation, as determined by the output characteristics, is better than that of the conventional single gate TFT. This is because the change in the source side potential barrier by the drain field has been suppressed.

• Journal of Information Display
• /
• v.5 no.2
• /
• pp.1-5
• /
• 2004

We developed an a-Si TFT-LCD panel with integrated gate driver circuit using a standard 5-MASK process. To minimize the effect of the a-Si TFT current and LC's capacitance variation with temperature, we developed a new a-Si TFT circuit structure and minimized coupling capacitance by changing vertical architecture above gate driver circuit. Integration of gate driver circuit on glass substrate enables single chip and 3-side free panel structure in a-Si TFT-LCD of QVGA ($240{\times}320$) resolution. And using double ASG structure the dead space of TFT-LCD panel could be further decreased.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.1
• /
• pp.18-26
• /
• 2004

Back-gated silicon-on-insulator MOSFET -a threshold-voltage adjustable device-employs a constant back-gate potential to terminate source-drain electric fields and to provide carrier confinement in the channel. This suppresses shortchannel effects of nano-scale and of high drain biases, while allowing a means to threshold voltage control. We report here a theoretical analysis of this geometry to identify its natural length scales, and correlate the theoretical results with experimental device measurements. We also analyze experimental electrical characteristics for misaligned back-gate geometries to evaluate the influence on transport behavior from the device electrostatics due to the structure and position of the back-gate. The backgate structure also operates as a floating-gate nonvolatile memory (NVRAM) when the back-gate is floating. We summarize experimental and theoretical results that show the nano-scale scaling advantages of this structure over the traditional front floating-gate NVRAM.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.1
• /
• pp.28-31
• /
• 2013

A volcano shaped gated Si-FEA (silicon field emitter array) was simply fabricated using sputtering as a gate electrode deposition and lift-off for the removal of the oxide mask, respectively. Due to the limited step coverage of well-controlled sputtering and the high aspect ratio in Si dry etch caused by high RF power, it was possible to obtain Si FEAs with a stable volcano shaped gate structure and to realize the restriction of gate leakage current in field emission characteristics. For 100 tip arrays and 625 tip arrays, gate leakage currents were restricted to less than 1% of the anode current in spite of the volcano-shaped gate structure. It was also possible to keep the emitters stable without any failure between the Si cathode and gate electrode in field emission for a long time.

• Water Engineering Research
• /
• v.1 no.1
• /
• pp.83-92
• /
• 2000

Jet flow can occur by gate opening at downstream of a hydraulic structure such as weir of drainage gate. If the stream bed is not hard or the bed protection is not sufficient, vortex erosion occurs and a resulting scour hole will be formed due to the high shear stress of the jet flow. Once the scour hole is formed, a vortex occurs in ti and this vortex causes additional erosion. If this erosion continues and reaches to the hydraulic structure, it can undermine the bottom of the hydraulic structure and this will lead to failure of the structure itself. Thus, it is necessary to define the physical features of the vortex structure in the scour hole for the design of the bed protection. This study presents the turbulent vortex structure in the scour hole by the gate opening of the hydraulic structure. Characteristics of vortex motion, circulation, vortex scale and vortex were analyzed through experiments. Experimental results of the vortex velocity were compared with theoretical ones. From these, circulation and vortex scale were obtained with known values of inflow depth, inflow velocity and scale of scour hole

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.490-493
• /
• 2002

In this study, we have investigated optimum value for side gate length and side gate voltage of double gate (DG) MOSFET with main gate and side gate. We know that optimum side gate voltage for each side length is about 3V. Also, we know that optimum side gate length for each main gate length is about 70nm. We have presented the transconductance and subthreshold slope for each side gate length. We have simulated using ISE-TCAD tool for characteristics analysis of device.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.15-24
• /
• 2021

In this paper, 1700 V EPDT (Extended P+ shielding floating gate Double Trench) MOSFET structure, which has a smaller switching time and loss than CDT (Conventional Double Trench) MOSFET, is proposed. The proposed EPDT MOSFET structure extended the P+ shielding area of the source trench in the CDT MOSFET structure and divided the gate into N+ and floating P- polysilicon gate. By comparing the two structures through Sentaurus TCAD simulation, the on-resistance was almost unchanged, but Crss (Gate-Drain Capacitance) decreased by 32.54 % and 65.5 %, when 0 V and 7 V was applied to the gate respectively. Therefore, the switching time and loss were reduced by 45 %, 32.6 % respectively, which shows that switching performance was greatly improved.

• Journal of IKEEE
• /
• v.27 no.3
• /
• pp.308-312
• /
• 2023

The gate current sensing structure was proposed to more effectively control the regulation of the output voltage when the LDO regulator occurs in an overshoot or undershoot situation. In a typical existing LDO regulator, the regulation voltage changes when the load current changes. However, the operation speed of the pass transistor can be further improved by supplying/discharging the gate terminal current in the pass transistor using a gate current sensing structure. The input voltage of the LDO regulator using the gate current sensing structure is 3.3 V to 4.5 V, the output voltage is 3 V, and the load current has a maximum value of 250 mA. As a result of the simulation, a voltage change value of about 12 mV was confirmed when the load current changed up to 250 mA.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.247-251
• /
• 2007

The recessed gate IGBT has a lower on-state voltage drop compared with the DMOS IGBT, because there is no JFET resistance. But because of the electric field concentration in the corner of the gate edge, the breakdown voltage decreases. This paper is about the new structure to effectively improve the Vce(sat) voltage without breakdown voltage drop in 1700V NPT type recessed gate IGBT with p floating shielding layer. For the fabrication of the recessed gate IGBT with p floating shielding layer, it is necessary to perform the only one implant step for the shielding layer. Analysis on the Breakdown voltage shows the improved values compared to the conventional recessed gate IGBT structures. The result shows the improvement on Breakdown voltage without worsening other characteristics of the device. The electrical characteristics were studied by MEDICI simulation results.