• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2013년도 추계학술대회
• /
• pp.361-364
• /
• 2013

기존의 DC-DC 부스트 변환기에서 사용되는 non-overlapping gate driver는 dead-time이 고정되어 있기 때문에 body-diode conduction loss 또는 charge-sharing loss가 발생하는 문제점을 가지고 있다. 이러한 손실을 줄이기 위해 사용된 기존의 적응제어 방식의 경우는 CCM 동작 시 전력트랜지스터가 동시에 on이 되는 구간이 발생하여 시스템 효율이 감소하는 문제점이 있다. 따라서 본 논문 에서는 이러한 문제점을 해결할 dead-time 적응제어 기능과 power switching 기능을 갖는 DC-DC 부스트 변환기를 설계 하였다. CMOS 0.35um 공정을 사용하였고, 2.5V 입력으로 3.3V의 출력전압을 얻으며, 스위칭 주파수는 500kHz 이다. 부하전류 150mA일 때 가장 높은 95.3%의 효율을 얻었다. 설계된 회로의 칩 면적은 $1720um{\times}1280um$이다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.174-176
• /
• 2003

The power conversion system must be increased switching frequency in order to achieve a small size, a light weight and a low noise. This paper proposes a skillful and a concise PWM DC-DC converter employing both zero voltage and zero current high frequency switching(ZVCS) operation. The Proposal ZVCS circuit is composed with resonant circuit using active resonant condenser. And this circuit provides switches with ZVS and ZCS by quasi resonant only that switching transients appear. This operation results in reduction of stress and losses in the power devices and resonant components. Some simulation results are included to confirm the validity of the analytical results.

• 대한전자공학회논문지SD
• /
• 제47권6호
• /
• pp.35-42
• /
• 2010

본 논문에서는 무선 통신 응용 시스템에 적합 하도록 10비트 80MHz 전류구동 방식의 D/A 변환기를 제안하였다. 제안한 회로는 $0.18{\mu}m$ CMOS n-well 1-poly 6-metal 공정을 이용하여 구현하였다. 10비트 중에서 LSB 4비트는 이진 디코더를 사용 하였으며, ULSB 3비트와 MSB 3비트는 온도계 디코더를 사용한 혼합구조를 채택하였다. 구현된 D/A 변환기의 측정결과, 샘플링 주파수가 80MHz, 입력 주파수 1MHz에서 SFDR은 60.42 dBc, 유효비트수는 8.75 비트를 보여주었다. INL/DNL은 ${\pm}$0.38LSB/${\pm}$0.32LSB로 측정되었으며, 글리치 에너지는 4.6 $pV{\cdot}s$로 나타났다. 전력 소모는 1.8V 전원전압에서 최대 속도인 80MHz일 때 48mW로 측정되었다.

• Journal of Power Electronics
• /
• 제17권6호
• /
• pp.1535-1544
• /
• 2017

Advances in FPGA technology have enabled fast real-time simulation of power converters, filters and loads. FPGA based HIL (Hardware-In-the-Loop) simulators have revolutionized control hardware and software development for power electronics. Common time step sizes in the order of 100ns are sufficient for simulating switching frequency current and voltage ripples. In order to keep the time step as small as possible, ideal switching function models are often used to simulate the phase legs. This often produces inferior results when simulating the discontinuous conduction mode (DCM) and disabled operational states. Therefore, the corresponding measurement and protection units cannot be tested properly. This paper describes a new solution for this problem utilizing a discrete-time PI controller. The PI controller simulates the proper DC and low frequency AC components of the phase leg voltage during disabled operation. It also retains the advantage of fast real-time execution of switch-based models when an accurate simulation of high frequency junction capacitor oscillations is not necessary.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1939-1949
• /
• 2016

This paper presents an alternative frequency adaptive grid synchronization technique named HDN-FLL, which can accurately extract the fundamental positive- and negative-sequence components and interested harmonics in adverse three-phase grid voltage. The HDN-FLL is based on the harmonic decoupling network (HDN) consisting of multiple first order complex vector filters (FOCVF) with a frequency-locked loop (FLL), which makes the system frequency adaptive. The stability of the proposed FLL is strictly verified to be global asymptotically stable. In addition, the linearization and parameters tuning of the FLL is also discussed. The structure of the HDN has been widely used as a prefilter in grid synchronization techniques. However, the stability of the general HDN is seldom discussed. In this paper, the transfer function expression of the general HDN is deduced and its stability is verified by the root locus method. To show the advantages of the HDN-FLL, a simulation comparison with other gird synchronization methods is carried out. Experimental results verify the excellent performance of the proposed synchronization method.

• 한국전기전자재료학회논문지
• /
• 제20권11호
• /
• pp.948-952
• /
• 2007

In this study, a low temperature sintering multilayer piezoelectric transformer for a DC-DC converter was manufactured using $(Pb,Ca,Sr,)(Ti,Mn,Sb)O_3$ ceramics. Its electrical properties were investigated according to the variation in frequency and load resistance. The voltage step-up ratio of the multilayer piezoelectric transformer showed a maximum value at a resonant frequency of input part and increased with an increase of load resistance. The efficiency of the multilayer piezoelectric transformer showed the highest value at a load resistance of 17 $\Omega$. The output power was increased with increasing input voltage. Temperature increase of the multilayer piezoelectric transformer was increased with the increase of output power. At the load resistance of 17 $\Omega$, the multilayer piezoelectric transformer showed the temperature rises of about $20^{\circ}C$ at the output power of 18 W, and stable driving characteristics.

• 조명전기설비학회논문지
• /
• 제27권3호
• /
• pp.79-86
• /
• 2013

In order to analyze the electrical performance of ZnO surge arresters stressed by the combined DC and AC voltages that are generated in DC/AC converter systems, the leakage current properties of ZnO surge arrester blocks deteriorated by impulse currents were investigated. The test specimens were deteriorated by the 8/$20{\mu}s$ impulse current of 2.5kA and the leakage currents flowing into the deteriorated zinc oxide(ZnO) arrester blocks subjected to the combined DC and power frequency AC voltages are measured. As a result, the leakage currents flowing through deteriorated ZnO surge arrester blocks were higher than those flowing through the fine ZnO surge arrester blocks and the larger the injection number of 8/$20{\mu}s$ impulse current of 2.5kA is, the greater the leakage current is. The leakage current-voltage curves(I-V curves) of the fine and deteriorated ZnO surge arrester blocks stressed by the combined DC and AC voltages show significant difference in the low conduction region. Also the cross-over phenomenon is observed at the voltage close to the knee of conduction on plots of I-V curves.

• 전자공학회논문지D
• /
• 제36D권9호
• /
• pp.37-45
• /
• 1999

박막형 다중접합 열전변환기의 시간에 따른 출력 전압 변화를 감소시키기 위해 벌크의 저항온도계수가 매우 적은 EVANOHM-S 합금을 박막 히터재료로 사용하였고, 또한 Seebeck 계수차이가 비교적 작은 크로멜-알루멜 열전쌍을 박막 열전퇴(thermopile)의 열전요소로 하였다. EVANOHM-S 박막 히터의 저항온도계수는 약 $1.4 {\times} 10^4/^{\circ}C$ 였고, 크로멜-알루멜 박막 열전쌍의 Seebeck 계수차이는 약 $38 {\mu}V/K$였다. 열전변환기의 출력 전압 변화는 공기중에서 처음 120초 동안 약 0.06%였고, 약 5분간이상 히터의 예열후 출력전압 변화는 현저히 감소하였다. 10 Hz ~ 10 kHz의 주파수 범위에서 열전변환기의 교류-직류 전압 및 전류 변환 오차범위는 각각 ${\pm}$1.6 ppm 및 ${\pm}$0.7 ppm이었고, 10Hz 이하 또는 10 kHz 이상의 주파수에서는 교류-직류 변환오차가 크게 증가하였다.

• 대한전자공학회논문지SD
• /
• 제46권6호
• /
• pp.16-24
• /
• 2009

본 논문에서는 인덕터와 커패시터를 집적화한 DC-DC 벅 변환기를 설계하였다. 출력전압의 리플크기를 줄이기 위해 stacked interleaved 방식을 이용하였고 변환기의 제어부는 전압모드 방식의 제어방법을 사용하여 설계하였다. 설계한 DC-DC 벅 변환기는 표준 $0.5{\mu}m$ CMOS 공정으로 제작 중이며 전체면적은 $9mm^2$이다. 설계된 회로는 $3V{\sim}5V$의 입력전압에서 동작하며 LC 필터의 크기를 줄이기 위해 50MHz의 주파수로 동작하였다. 최대 250mA의 부하전류 구동이 가능하며 최대 71%의 전력변환 효율을 가졌다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1488-1490
• /
• 2008

The gyroscope is the sensor for detecting the rotation in inertial reference frame and constitute the navigation system together an accelerometer. As the inertial reference equipment for attitude determination and control in the satellite, the mechanical gyroscope has been used but it bring the disturbance for mass unbalance so the disturbance give a bad influence to the observation satellite mission because the mechanical gyroscope has the rotation parts. During the launch, The mechanical gyroscope is weak in vibration, shock and has the defect of narrow operating temperature range so it need the special design in integration. Recently the low orbit observation satellite for seeking the high pointing accuracy of image camera payload accept the FOG(Fiber Optic Gyro) or RLG(Ring Laser Gyro) for the attitude determination and control. The Ring Laser Gyro makes use of the Sanac effect within a resonant ring cavity of a He-Ne laser and has more accuracy than the other gyros. It need the 1000V DC to create the He-Ne plasma in discharge tube. In this paper, the design process of the High Voltage Power Supply for RLG(Ring Laser Gyroscope) is described. The specification for High Voltage Power Supply(HVPS) is proposed. Also, The analysis of flyback converter topology is explained. The Design for the HVPS is composed of the inverter circuit, feedback control circuit, high frequency switching transformer design and voltage doubler circuit.