• 대한기계학회논문집A
• /
• 제30권8호
• /
• pp.931-940
• /
• 2006

Defect assessment of a weld zone is important in fitness-for-service evaluation of plant components. Typically a J and $C^*$ estimation method for a defective homogeneous component is extended to a mismatched component, by incorporating the effect due to the strength mismatch between the weld metal and the base material. The key element is a mismatch limit load. For instance, the R6/R5 procedure employs an equivalent material concept, defined by a mismatch limit load. A premise is that if a proper mismatch limit load solution is available, the same concept can be used for any defect location (either a weld centre defect or a heat affected zone (HAZ) defect) and for any material combination (either two-material or multi-material combinations; either similar or dissimilar joints). However, validation is still limited, and thus a more systematic investigation is needed to generalise the suggestion to any geometry, any defect location and any material combination. This paper describes the effect of structural geometry on the $C^*$ integral for defective similar welds, based on systematic elastic-creep 2-D and 3-D finite element (FE) analyses, to attempt to elucidate the questions given above. It is found that the existing 'equivalent material' concept is valid only for limited cases, although it provides conservative estimates of $C^*$ for most of cases. A modification to the existing equivalent material concept is suggested to improve accuracy.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1270-1279
• /
• 2002

Residual stress is a dominant obstacle to efficient production and safe usage of device by deteriorating the mechanical strength and failure properties. Therefore, we proposed a new thin film stress-analyzing technique using a nanoindentation method. For this aim, the shape change in the indentation load-depth curve during the stress-relief in film was theoretically modeled. The change in indentation depth by load-controlled stress relaxation process was related to the increase or decrease in the applied load using the elastic flat punch theory. Finally, the residual stress in thin film was calculated from the changed applied load based on the equivalent stress interaction model. The evaluated stresses for diamond-like carbon films from this nanoindentation analysis were consistent with the results from the conventional curvature method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.63-65
• /
• 2003

In the case of the large motors which can't direct load tests, IEEE 112 equivalent circuit test was selected instead of the circle diagram method in the newly KEPIC's code. According to the change of code, Hyosung established an equivalent circuit test method based on Standard IEEE 112. In this paper, we compared the test results between IEEE 112 and other standards, CSA C-390, JEC2137 for the large motors.

• 한국가스학회지
• /
• 제20권3호
• /
• pp.73-77
• /
• 2016

본 연구에서는 여러 가지의 절단면 형상을 구비한 중공축이 동등한 최적을 갖는 경우에 대한 변위거동 안전성을 유한요소법으로 해석하였다. FEM 해석결과에 의하면, 외측튜브, 중간튜브, 내측튜브와 이들 튜브 사이를 연결하기 위해 X-타입 또는 Y-타입의 칼럼을 설치하였을 때 중공축 길이의 중간부에서 발생하는 최대 변위량을 줄여주는 것으로 나타났다. 특히, 하중을 지지하기 위해 구비된 X-타입 또는 Y-타입의 칼럼을 위상차 없이 외측튜브와 내측튜브를 중심축을 향해 직접 연결하면 중공축의 변위량을 줄이는 효과가 있는 것으로 나타났다. 그리고 동등한 체적을 갖는 중공축에서 발생하는 수직 변위량을 줄여주고, 변위거동 안전성을 높이기 위해서는 하중을 지지하기 위한 칼럼의 두께를 두껍게 설계하는 것이 바람직함을 알 수 있다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.282-286
• /
• 1999

This paper presents a vector control of parallel drive, a beatless control and a low switching PWM technique for the propulsion system of Electric car as transient state which are included interrupting line voltage, changing line voltage slowly, suddenly, regenerating light load and starting from backward running. Improved performance and a validation of proposed method is shown by the experimental results using a 1.65MVA IGBT VVVF inverter and inertia load equivalent to 160 tons electric cars through a running and transient state test.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.413-420
• /
• 2002

Recent experimental research results of connection method between steel pipe pile and concrete footing are provided based on various experimental observations. It gives a shedding light toward developing better and concrete connection method for steel pipe pile at the field application. In this study, the newly developed method is tested for compressive, pull put and combination load including moment with carefully designed monitoring system. The measured data show that new method have at least equivalent or better load resistant capacities compared with those of specified method in Korea Highway Corporation design code. It is also tried to define and investigate the load transfer mechanism for new method.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3149-3158
• /
• 1994

In this paper, using the formulation of dynamic equivalent load considering the effects of moment load and the equation to estimate the cage rotational speed, the new life equation of deep groove ball bearing under radial and moment loads was proposed. Fatigue life test apparatus with the measuring equipment of shaft and cage speed was designed and developed to be capable of subjecting combined radial and moment load. Fatigue life tests were executed by sudden death test method and the reliability of fatigue lives was evaluated by Weibull distribution analysis. From the results of fatigue tests and analysis, the relationships between film parameters and life adjustment factors were acquired. And it was turned out that so as to estimate the effect of moment load on fatigue life, the life adjustment factor as well as the dynamic equivalent load must be taken into account.

• Steel and Composite Structures
• /
• 제22권2호
• /
• pp.217-234
• /
• 2016

In order to investigate mechanical properties and load-bearing capacity of T-shaped Concrete-Filled Square Steel Tubular (TCFST) composite columns under eccentric axial load, three T-shaped composite columns were tested under eccentric compression. Experimental results show that failure mode of the columns under eccentric compression was bending buckling of the whole specimen, and mono column performs flexural buckling. Specimens behaved good ductility and load-bearing capacity. Nonlinear finite element analysis was also employed in this investigation. The failure mode, the load-displacement curve and the ultimate bearing capacity of the finite element analysis are in good agreement with the experimental ones. Based on eccentric compression test and parametric finite element analysis, the calculation formula for the equivalent slenderness ratio was proposed and the bearing capacity of TCFST composite columns under eccentric compression was calculated. Results of theoretical calculation, parametric finite element analysis and eccentric compression experiment accord well with each other, which indicates that the theoretical calculation method of the bearing capacity is advisable.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권4호
• /
• pp.239-246
• /
• 2004

충격하중에 대한 양단 고정보의 거동을 강 소성 모델을 이용하여 파악 하였다. 또한 손상을 발생시키는 정 역학적 붕괴하중과 이상임펄스에 대한 하중최대치 비와 임펄스 비를 이용하여 손상곡선을 작성하였다. 작성된 손상곡선으로부터 충격하중의 하중 최대치와 임펄스는 구조물의 안전에 중요 변수가 됨을 보였으며 또한 하중최대치 비와 임펄스 비로 작성된 손상곡선은 하중작용시간과 하중의 형태 그리고 구조물의 동적 특성이 함께 고려된 기준으로, 등가 동하중에 초점을 맞추어 일괄적으로 구조물의 안전성을 판단할 수 있는 방법이다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권1호
• /
• pp.157-164
• /
• 2004

강 소성 모델을 이용한 단순보의 손상곡선을 소성힌지를 발생시키는 정역학적 붕괴하중과 이상임펄스에 대한 하중최대치 비와 임펄스 비를 이용하여 작성하였다. 작성된 손상곡선으로부터 임펄스와 하중 최대치가 구조물의 안전에 중요 변수가 됨을 보였으며 또한, 하중최대치 비와 임펄스 비로 작성된 손상곡선은 하중작용시간과 하중의 형태 그리고 구조물의 동적 특성이 함께 고려된 기준으로, 등가 동하중에 초점을 맞추어 일괄적으로 구조물의 안전성을 판단할 수 있는 방법이다.