• Korean Journal of Computational Design and Engineering
• /
• v.21 no.4
• /
• pp.389-396
• /
• 2016

The necessity for environment-friendly material development has emerged in the recent automotive field due to stricter regulations on fuel economy and environmental concerns. Accordingly, the automotive industry is paying attention to carbon fiber reinforced plastic (CFRP) material with high strength and stiffness properties while the lightweight. In this study, we determine a shape of lower control arm (LCA) for maximizing the strength and stiffness by optimizing the thickness of each layer when the stacking angle is fixed due to the CFRP manufacturing problems. Composite materials are laminated in the order of $0^{\circ}$, $90^{\circ}$, $45^{\circ}$, and $-45^{\circ}$ with a symmetrical structure. For the approximate optimal design, we apply a sequential two-point diagonal quadratic approximate optimization (STDQAO) and use a process integrated design optimization (PIDO) code for this purpose. Based on the physical properties calculated within a predetermined range of laminate thickness, we perform the FEM analysis and verify whether it satisfies the load and stiffness conditions or not. These processes are repeated for successive improved objective function. Optimized CFRP LCA has the equivalent stiffness and strength with light weight structure when compared to conventional aluminum design.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5844-5853
• /
• 2014

This paper presents the results of experimental investigations on the shear failure behaviors of reinforced concrete beams using ductile fiber reinforced cementitious composite (DFRCC). Total 10 RC beams of $150{\times}300{\times}1,000mm$ size were tested by 4-point bending under the displacement control. The main parameters of the experiment are surface treatment by grinding and preloading to the cracking point in the repair process. The load-displacement curves, diagonal tension cracking load, flexural cracking load, and shear strength were obtained. The test results showed that the DFRCC can be used effectively for restoring the shear strength approximately 99% to the original value under the condition that the appropriate thickness and surface treatment like grinding are assured. For further research, the specimens taken from real deteriorated structures will need to be tested after being repaired with DFRCC.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.334-339
• /
• 1994

In this work, we propose a planar three degree-of-freedom parallel mechanism as another type of assembly device which utilized joint compliances. These joint compliances can be adjusted either by properly replacing the joint compliances or by actively controlling stiffness at joints, in order to generate the desired operational compliance characteristics at RCC point, The operational compliance matrix for this mechanism is explicitly obtained by symbolic manipulation and its operational compliance characteristics are examined, it is found that the RCC point exists at the center of the workspace when the mechanism maintains symmetric configurations. Compliance characteristic and its sensitivity of this mechanism is analyzed with respect to the magnitude of the diagonal compliance components and two different matrix norms measuring compliance sensitivity. It is expected that the analysis results provide the designer with a helpful information to determine a set of optimal parameters of this RCC mechanism.

• Proceedings of the KIEE Conference
• /
• 2003.11b
• /
• pp.315-318
• /
• 2003

This paper proposes a switching control method applicable to any affine, 2nd order nonlinear system with single input. The key contribution is to develop a control design method which uses a piecewise continuous Lyapunov function non-increasing at every discontinuous point. The proposed design method requires no restrictions except full state availability. To obtain a non-increasing, piecewise continuous Lyapunov function, we change the sign of off-diagonal term s of the positive definite matrix composing the former Lyapunov function according to the sign of the Inter-connection term. And we use the solution of inequalities which guarantee each Lyapunov function is non-increasing at any discontinuous point.

• Wind and Structures
• /
• v.34 no.2
• /
• pp.161-171
• /
• 2022

This paper presents a failure type assessment curve method to judge the failure type of transmission tower segments. This novel method considers the equivalent static wind load characteristics and the transmission tower members' load-bearing capacities based on numerical simulations. This method can help judge the failure types according to the relative positions between the actual state points and the assessment curves of transmission tower segments. If the extended line of the actual state point intersects with the horizontal part's assessment curve, the segment would lose load-bearing capacity due to the diagonal members' failure. Another scenario occurs when the intersection point is in the oblique part, indicating that the broken main members have caused the tower segment to fail. The proposed method is verified by practical engineering case studies and static tests on the scaled tower segments.

• Radiation Oncology Journal
• /
• v.12 no.2
• /
• pp.225-232
• /
• 1994

Purpose : This study was to obtain the basic dosimetric data using the 10 MV X-ray for the total body irradiation. Materials and Methods : A linear accelerator photon beam is planned to be used as a radiation source for total body irradiation (TBI) in Chonnam University Hospital. The planned distance from the target to the midplane of a patient is 360cm and the maximum geometric field size is 144cm x 144cm. Polystyrene phantom sized $30{\times}30{\times}30.2cm^3$ and consisted of several sheets with various thickness, and a parallel plate ionization chamber were used to measure surface dose and percent depth dose (PDD) at 345cm SSD, and dose profiles. To evaluate whether a beam modifier is necessary for TBI, dosimetry in build up region was made first with no modifier and next with an 1cm thick acryl plate 20cm far from the polystyrene phantom surface. For a fixed sourec-chamber distance, output factors were measured for various depth. Results : As any beam modifier was not on the way of radiation of 10MV X-ray, the $d_{max}$ and surface dose was 1.8cm and $61\%$, respectively, for 345cm SSD. When an 1cm thick acryl plate was put 20cm far from polystyrene phantom for the SSD, the $d_{max}$ and surface dose were 0.8cm and $94\%$, respectively. With acryl as a beam spoiler, the PDD at 10cm depth was $78.4\%$ and exit dose was a little higher than expected dose at interface of exit surface. For two-opposing fields for a 30cm phantom thick phantom, the surface dose and maximum dose relative to mid-depth dose in our experiments were $102.5\%$ and $106.3\%$, respectively. The off-axis distance of that point of $95\%$ of beam axis dose were 70cm on principal axis and 80cm on diagonal axis. Conclusion: 1. To increase surface dose for TBI by 10MV X-ray at 360cm SAD, 1cm thick acrylic spoiler was sufficient when distance from phantom surface to spoiler was 20cm. 2. At 345cm SSD, 10MV X-ray beam of full field produced a satisfiable dose uniformity for TBI within $7\%$ in the phantom of 30cm thickness by two-opposing irradiation technique. 3. The uniform dose distribution region was 67cm on principal axis of the beam and 80cm on diagonal axis from beam axis. 4. The output factors at mid-point of various thickness revealed linear relation with depth, and it could be applicable to practical TBI.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.6
• /
• pp.951-957
• /
• 2002

When retrieving voluminous capacity of video image data, it is necessary to provide synopsized frame lists of video image data for indexing and replaying at the exact point where the user want to retrieve. We apply Mean Squared Error method to extract certain pixel value from diagonal direction of a frame. The RGB value of a pixel extracted from each frame is saved in a matrix form, and this frame is retrievedas a scene change point if the compared value of two points met the certain condition. Also implement the algorithm and provide a way to seize entire structure of video image and the point of scene changes. finally, we analyze and prove that our method has better performance compared with the others.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.5
• /
• pp.215-226
• /
• 2018

In this paper, to estimate the dynamic behavior of a submerged floating tunnel(SFT) by underwater explosion(UE), the SFT is modeled and analyzed by the explicit structural analysis package LS-DYNA. The section of SFT near to explosion point is modeled to shell and solid elements using elasto-plasticity material model for concrete tubular section and steel lining. And the other parts of the SFT are modeled to elastic beam elements. Also, mooring lines are modeled as tension-only cable elements. Total mass of SFT is including an added mass by hydrodynamic effect. The buoyancy on the SFT is considered in its initial condition using a dynamic relaxation method. The accuracy and the feasibility of the analysis model aree verified by the results of series of free field analysis for UE. And buoyancy ratio(B/W) of SFT, the distance between SFT and an explosion point and the arrangement of mooring line aree considered as main parameters of the explosion analysis. As results of the explosion analysis, the dynamic responses such as the dent deformation by the shock pressure are responded less as more distance between SFT and an explosion point. However, the mooring angle of the diagonal mooring system can not affect the responses such as the horizontal displacement of SFT by the shock pressure.

• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.504-508
• /
• 2003

We present a new point-diffraction interferometer, which has been devised for the three-dimensional profile measurement of light scattering rough surfaces. The interferometer system has multiple sources of two-point-diffraction and a CCD camera composed of an array of two-dimensional photodetectors. Each diffraction source is an independent two-point-diffraction interferometer made of a pair of single-mode optical fibers, which are housed in a ceramic ferrule to emit two spherical wave fronts by means of diffraction at their free ends. The two spherical wave fronts then interfere with each other and subsequently generate a unique fringe pattern on the test surface. A He-Ne source provides coherent light to the two fibers through a 2${\times}$l optical coupler, and one of the fibers is elongated by use of a piezoelectric tube to produce phase shifting. The xyz coordinates of the target surface are determined by fitting the measured phase data into a global model of multilateration. Measurement has been performed for the warpage inspection of chip scale packages (CSPs) that are tape-mounted on ball grid arrays (BGAs) and backside profile of a silicon wafer in the middle of integrated-circuit fabrication process. When a diagonal profile is measured across the wafer, the maximum discrepancy turns out to be 5.6 ${\mu}{\textrm}{m}$ with a standard deviation of 1.5 ${\mu}{\textrm}{m}$.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.5
• /
• pp.1367-1376
• /
• 1998

In this paper we propose an real time marker detection algorithm for motion analysis both in 2 dimensions and 3 dimensions with CCD camera and rfame grabber only which has no image processor. The main algorithm consists of the following 3 algorithms; 1) the tracing algorithm that makes it possible to predict the expected marker location by narrowing the searching boundary, 2) the searching algorithm that detects the marker in the expected boundary using Ad-hoc previous screen search technique, tornado search method rotate diagonal search method search technique, 3) the algorithm that finds the central point of the detected marker. We try to narrow the searching boundary for real time processing. Also, it is able to find the central point of the detected marker much faster than typical contour tracing algorithm.