• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.7
• /
• pp.48-55
• /
• 1998

We propose a new static current source model and parameter extraction method for AlGaAs/GaAs HBT. The proposed model has 9 parameters describing internal currents and are experessed with the physically meaningful parameters.The proposed parameter extraction method uses the measured dC IV curves and does not need the gummel plt data and any optimization process. the constructed model based on the proposed method predicts the measured data well.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.6
• /
• pp.34-41
• /
• 1993

This paper describes an effort to develop a microcomputer-based parameter identification system for three phase and two phase brushless DC motor. Back EMF equation is derived from back EMF waveform of three phase and two phase brushless DC motor. In this paper, a new identification algorithm for the brushless DC motor parameters by Pasek's technique is de veloped. It is found that Pasek's equation is valid for the brushless DC motor, too. The results obtained clearly shows that it is possible to implement the identification system for the determination of the brushless DC motor parameters. To minimize errors due to the ripple component in the measured armature current, dlgital averaging filter is employed. The whole identification process of signal generation, measuring, parameter determination is fully automated. The use of the pmpased method in the parameter identification system shows that the averaged current curve is in excellent agreement with the estimated current curve. Therefore, this close agreement conf i i the validity of this technique.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.2
• /
• pp.61-69
• /
• 2003

In this paper, we developed the U parameter test system which inspects the property of DC parameter for semiconductor products. The developed system is interfaced by IBM-PC. It is consisted of CPLD part, ADC (Analogue to Digital Converter), DAC (Digital to Analogue Converter), voltage/current source, variable resistor and measurement part. In the proposed system, we have designed the constant voltage source and the constant current source in a part. The CPLD part is designed by VHBL, which it generates the control and converts the serial data to parallel data. The proposed system has two test channels and it operates VFCS mode and CFVS mode. The range of test voltage is from 0[V] to 100[V], and the range of test current is from 0[mA] to 100[mA)]. The diode is tested. The test results have a good performance.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.2
• /
• pp.41-50
• /
• 1993

This paper describes an effort to develop a microcomputer-based parameter identification system for three phase and two phase brushless DC motor. Back EMF equation is derived from back EMF waveform of three phase and two phase brushless DC motor. In this paper, a new identification algorithm for the brushless DC motor parameters by Pasek's technique is developed. It is found that Pasek's equation is valid for the brushless DC motor, too. The results obtained clearly shows that it is possible to implement the identification system for the determination of the brushless DC motor parameters. To minimize errors due to the ripple component in the measured armature current, digital averaging firis employed. The whole identification process of signal generation, measuring, parameter determination is fully automated. The use of the propod method in the parameter identifition system shows that the averaged current curve is in excellent agreement with the estimated current curve. Therefore, this close agreement confirms the validity of this technique.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1126-1129
• /
• 2000

The equivalent transformation of a brushless DC motor into an separately exited DC motor has been possible with the vector control technique. Vector control is an effective technique for controlling variable speed drives of brushless DC motors. Conventional vector controllers, however, suffer from electrical machine parameter variations because these controllers depend on the parameters. This paper presents the vector control of brushless DC motor using a neural network. In the proposed method, a neural network is employed as on-line estimator of the nonlinear dynamic equations of brushless DC motor. The neural network based vector controller has the advantage of robustness against machine parameter variations as compared with conventional vector controller The simulation results using Matlab/Simulink verify the useful of the proposed method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.8
• /
• pp.1840-1846
• /
• 2005

In this paper, does by purpose DC servo motor speed controller design about PID coefficient tuning techniques that use genetic algerian. DC servo motor is used in application field of a peat many control machine or robot etc. and in this field, selection of controller parameters requires user's expert knowledge. Therefore, general amount of work engineers must continuously iteration tuning in controller parameters by trial and error. With this, when must tuning parameter coefficient about change of dynamic system or disturbance, can improve the efficiency according to following that is more precised and parameter coefficient value that is optimized by using genetic algorithm. In this paper, from dynamic character modeling get in analyze dynamic character of DC motor desist controller drive control possible that is fast response character md improved speed precision using a Genetic Algorithms.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2281-2285
• /
• 2011

An algorithm for extracting SPICE MOS level 2 model parameters for the high voltage MOSFET DC model is proposed. The optimization method for analyzing the nonlinear data of the current-voltage curve using the Gauss-Newton algorithm is proposed and the pre-process step for calculating the threshold voltage and the mobility is proposed. The drain current obtained from the proposed method shows the maximum relative error of 5.6% compared with the drain current of 2-dimensional device simulation for the high voltage MOSFET.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.5
• /
• pp.321-327
• /
• 2018

DC microgrid system composed of multiple converters has a tendency to make the system unstable due to the interaction of converters. To solve this problem, in this paper, the interaction between cascaded converters with LC input filter is analyzed with impedance modeling using g-parameter. The input impedance and the output impedance of the system can be obtained through this technique. The stability of the system can be determined by applying Middlebrook's stability criterion to the impedance. Virtual impedance is added to the controller to enhance stability. The validity of the analysis is verified by the result of several simulations and experiments.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.418-421
• /
• 1988

A disturbance and parameter variations cause a steady and/or transient error in the conventional de servo motor drive system. In this paper robust control system for dc servo motor drive taking disturbance and parameter variations into account is proposed. The proposed control system compensates rapidly the state error caused by disturbance and parameter variations. Simulation results show that the proposed method is robust for the steady and transient response in the presence of both disturance and parameter variations.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.542-548
• /
• 2012

This study presents a new method of system modeling by using the Discrete Fourier Transform for the position control system of DC Motor. And the proposed method is similar to the method of System Identification by analysis of correlation of the measured input-output data. The measured output signals are transformed to the frequency domain using DFT. The Fourier Spectrum of the transformed signals is used for knowing to the feature of having an important effect on the system. And transfer function of the second order system is estimated by the dominant parameter which is computed in the magnitude and the phase of Fourier spectrum of the transformed signals. In addition, the output signal includes the unique feature of system. So, although the basic parameter of the system is unknown for us, the proposed method has an advantage to system modeling. And the controller is easily designed by the estimated transfer function. Thus, in this paper, the proposed method is applied to the system modeling for the position control system of DC Motor and the PD-controller is designed by the estimated model. And the efficiency and the reliability of the proposed method are verified by the experimental result.