• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.64-69
• /
• 2003

There exist the high frequency components, which can not be predicted by the low frequency model, due to the presence of sampling effect in current mode control. In this paper, the output voltage equations for the ZVS half bridge PWM convertor are derived from the steady state analysis, and the sampling gain presented in the current control loop is Investigated to improve the Prediction Performance of low frequency model of ZVS half bridge PWM converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.2
• /
• pp.168-174
• /
• 2016

In this paper, current control using PI controller in the synchronous reference frame is analyzed through the relationship among bandwidth, resonance frequency, and sampling frequency in the grid-connected inverter with LCL filter. Stability is investigated by using bode plot in frequency domain and root locus in discrete domain. The feedback variable is the grid current, which is regulated by the PI controller in the synchronous reference frame. System delay is modeled as 1.5Ts, which contains computational and PWM modulator delay. Two resonance frequencies are given at 815 Hz and 3.16 kHz from LCL filter parameters. Sufficient phase and gain margins can be obtained to guarantee stable current control, in case that resonance frequency is above one-sixth of the sampling frequency. Unstable current control is performed when resonance frequency is below one-sixth of the sampling frequency. Analysis results of stability from frequency response and discrete response is the same regardless of resonance frequency. Finally, stability of current control based on theoretical analysis is clearly verified through simulation and experiment in grid-connected inverters with LCL filter.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.227-237
• /
• 2016

A novel digital current control strategy for digitally controlled DC-DC switching converters, referred to as Adjacent Cycle Sampling (ACS), is proposed in this paper. For the ACS current control strategy, the available time interval from sampling the current to updating the duty ratio, is approximately one switching cycle. In addition, it is independent of the duty ratio. As a result, the contradiction between the processing speed of the hardware and the transient response speed can be effectively relaxed by using the ACS current control strategy. For digitally controlled buck DC-DC switching converters with trailing-edge modulation, digital current control algorithms with the ACS control strategy are derived for three different control objectives. These objectives are the valley, average, and peak inductor currents. In addition, the sub-harmonic oscillations of the above current control algorithms are analyzed and eliminated by using the digital slope compensation (DSC) method. Experimental results based on a FPGA are given, which verify the theoretical analysis results very well. It can be concluded that the ACS control has a faster transient response speed than the time delay control, and that its requirements for hardware processing speed can be reduced when compared with the deadbeat control. Therefore, it promises to be one of the key technologies for high-frequency DC-DC switching converters.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.54 no.1
• /
• pp.80-89
• /
• 2021

In Korea, marine fish landed at ports are randomly sampled on a periodic basis (e.g., daily or weekly), and body sizes (e.g., lengths and weights) of those sampled fish are measured. The motivation for our study is whether or not such measurements reflect the size distribution, especially the length distribution of fish landed (= a population), because such length measurements are key data for a length-based assessment model. The current sampling method is to sample fish landed at ports by body size group (e.g., very small, small, medium, large, very large), using the sampling weights as the number of boxes by body size group. In this study, we showed that length composition data about fish sampled by the current method did not represent the length frequency distribution of the fish landed, and suggested that an alternative sampling method should be applied of using the sampling weights as the number of fish landed by body size group. We also introduced a method for determining an appropriate sample size.

• Journal of Korean Society for Quality Management
• /
• v.23 no.3
• /
• pp.45-56
• /
• 1995

The method of lot by lot quality protection for sampling inspection by variables is widely used in quality control. In case of sampling inspection being done repeatedly, one can use the information from the previous sampling inspection to improve current estimates. This article shows that empirical Bayes estimator is superior to the usual sample mean in repeated sampling inspection by variables.

• Journal of Power Electronics
• /
• v.4 no.2
• /
• pp.102-111
• /
• 2004

This paper is concerned with a deadbeat current control implementation of shunt-type three-phase active power filter (APF). Although the one-dimensional deadbeat control method can attain time-optimal response of APF compensating current, one sampling period is actually required fur its settling time. This delay is a serious drawback for this control technique. To cancel such a delay and one more delay caused by DSP execution time, the desired APF compensating current has to be predicted two sampling periods ahead. Therefore an adaptive predictor is adopted for the purpose of both predicting the control error of two sampling periods ahead and bringing the robustness to the deadbeat current control system. By adding the adaptive predictor output as an adjustment term to the reference value of half a source voltage period before, settling time is made short in a transient state. On the other hand, in a steady state, THD (total harmonic distortion) of the utility grid side AC source current can be reduced as much as possible, compared to the case that ideal identification of controlled system could be made.

• Korean Journal of Poultry Science
• /
• v.45 no.4
• /
• pp.285-290
• /
• 2018

This study was aimed to evaluate the possibility of application to the KS A ISO 2859-1 Easy test, an international standards sampling inspection, to replace a sampling method of the current grading standard of chicken meats for the first time. As a result of screening capability to check for defective products, the current sampling was 0.61 and the KS A ISO 2859-1 Normal test was 0.70, suggesting that the latter inspection method was more accurate. If the KS A ISO 2859-1 conversion principle is applied, 40,530 won per day is saved for a 50-lot inspection. The current sampling and the KS A ISO 2859-1 Easy test did not exceed the reject limit for the number of defective products to satisfy the grade $1^+$ on chicken carcass size numbers 12, 9 and 8. Freshness was not significantly different between the current sampling and the KS A ISO 2859-1 Easy test. It is expected that using the KS A ISO 2859-1 Easy test with a smaller sample volume will have the same level of quality evaluation as the current sampling method while reducing costs.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.609-614
• /
• 1998

A new small signal modeling of an average current mode control is proposed. In order to analyze the characteristics of the control scheme, the discrete and continuous time small signal models are derived. The derivation are mainly come from the analysis of the sampling effect presented in the current control loop. By the mathematical interpretation of practical sampler representing the sampling effect of a current control loop, the small signal models of an average current mode control can be easily derived. The instability of the current control loop, which gives rise to the subharmonic oscillation, can be identified by the proposed models. To show the usefulness of the proposed models, the simulation and experiment are carried out. The results show that the predicted results by the proposed model are much better agreed with the measured ones than that of the conventional model, even though the high gain of the compensation network of a current control loop is employed.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.686_687
• /
• 2009

The traceability maintenance system for the AC voltage and current has been developed at the frequency range of 20 Hz to 100 Hz without using any compensation technique which is used at thermal converter (TC) ac-dc transfer system at low frequencies. The system uses a digital voltmeter (DVM) as a data acquisition system of the input waveform and stored data in memory. The developed algorithm acquires and processes the sampling data to calculate the root mean square (rms) value of the input voltage of DVM which operates at DC 10 V range for better accuracy. The best uncertainty of the AC voltage measurements is $3 {\mu}V/V$ within the frequency range. The best uncertainty of the AC current measurements is better than the $5 {\mu}A/A$ and mainly depend on the current to voltage converter, ac-dc current shunt or Current Transformer (CT), used for the measurement

• Journal of the Korean Society of Safety
• /
• v.27 no.6
• /
• pp.48-53
• /
• 2012

This paper is purposed to develop portable electric instrument to select NI-9223(National instrument comp.) and clamp meter(HIOKI comp.), which can be used in developing electric instrument, to detect leakage current(ZCT) and current(CT) signals. In this paper, The electric instrument that can interface with current and leakage current instrument(HIOKI 9283), is developed by NI-9223 of NI comp.. HIOKI clamp meter can measure current signals certainly by high-sensitivity of 10 ${\mu}A$ resolution(leakage current : at 10 mA range) and current 1~200A range. The NI-9223 use four 16-bit analog-to-digital converters(ADCs) for true simultaneous sampling at up to 1 MS/s per channel. NI-9223 can synchronize all analog input modules installed in the same chassis to share the same start clock and/or sample clocks. The monitoring program is developed by SignalExpress of LabVIEW. The monitoring program are developed to analyze at simultaneous sampling on electrical signals such as leakage current(ZCT) and current(CT). The developed system verification tests were conducted, and portable electric instrument can be used in place which requires analysis of the actual electrical signal.