• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.3
• /
• pp.404-416
• /
• 2015

Small-area, low-power coarse and fine frequency detectors (FDs) are proposed for an adaptive bandwidth referenceless CDR with a wide range of input data rate. The coarse FD implemented with two flip-flops eliminates harmonic locking as long as the initial frequency of the CDR is lower than the target frequency. The fine FD samples the incoming input data by using half-rate four phase clocks, while the conventional rotational FD samples the full-rate clock signal by the incoming input data. The fine FD uses only a half number of flip-flops compared to the rotational FD by sharing the sampling and retiming circuitry with PLL. The proposed CDR chip in a 65-nm CMOS process satisfies the jitter tolerance specifications of both USB 3.0 and USB 3.1. The proposed CDR works in the range of input data rate; 2 Gb/s ~ 8 Gb/s at 1.2 V, 4 Gb/s ~ 11 Gb/s at 1.5 V. It consumes 26 mW at 5 Gb/s and 1.2 V, and 41 mW at 10 Gb/s and 1.5 V. The measured phase noise was -97.76 dBc/Hz at the 1 MHz frequency offset from the center frequency of 2.5 GHz. The measured rms jitter was 5.0 ps at 5 Gb/s and 4.5 ps at 10 Gb/s.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.11A
• /
• pp.929-935
• /
• 2003

An analog/digital mixed mode ASIC for network synchronization of ATM switching system has been designed and fabricated. This ASIC generates a 234.7/46.94 ㎒ system clock and 77.76/19.44 ㎒ user clock using 46.94 ㎒ transmitted clocks from other systems. It also includes digital circuits for checking and selecting of the transmitted clocks. For effective ASIC design, full custom technique is used in 2 analog PLL circuits design, and standard cell based technique is used in digital circuit design. Resistors and capacitors for analog circuits are specially designed which can be fabricated in general CMOS technology, so the chip can be implemented in 0.8$\mu\textrm{m}$ digital CMOS technology with no expensive. Testing results show stable 234.7 ㎒ and 19.44 ㎒ clocks generation with each 4㎰ and 17㎰ of low ms jitter.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.19-24
• /
• 2007

With recent advancement of high-speed, multi-gigabit data transmission capabilities, serial links have been more widely adopted in industry than parallel links. Since the parallel link design forces its transmitter to transmit both the data and the clock to the receiver at the same time, it leads to hardware's intricacy during high-speed data transmission, large power consumption, and high cost. Meanwhile, the serial links allows the transmitter to transmit data only with no synchronized clock information. For the purpose, clock and data recovery circuit becomes a very crucial key block. In this paper, a 5.4Gbps half-rate bang-bang CDR is designed for the applications of high-speed graphic DRAM interface. The CDR consists of a half-rate bang-bang phase detector, a current-mirror charge-pump, a 2nd-order loop filter, and a 4-stage differential ring-type VCO. The PD automatically retimes and demultiplexes the data, generating two 2.7Gb/s sequences. The proposed circuit is realized in 66㎚ CMOS process. With input pseudo-random bit sequences (PRBS) of $2^{13}-1$, the post-layout simulations show 10psRMS clock jitter and $40ps_{p-p}$ retimed data jitter characteristics, and also the power dissipation of 80mW from a single 1.8V supply.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.3
• /
• pp.185-192
• /
• 2013

In this paper, a clock and data recovery (CDR) circuit that supports triple data rates of 1.62, 2.7, and 5.4 Gbps for DisplayPort 1.2 standard is described. The proposed CDR circuit covers three different operating frequencies with a single VCO switching the operating frequency by the 3-bit digital code. The prototype chip has been designed and verified using a 65 nm CMOS technology. The recovered-clock jitter with the data rates of 1.62/2.7/5.4 Gbps at $2^{31}$-1 PRBS is measured to 7/5.6/4.7 $ps_{rms}$, respectively, while consuming 11 mW from a 1.2 V supply.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.633-640
• /
• 2007

We report an experimental demonstration of 40 Gbps all-optical 3R regeneration with all-optical clock recovery based on InP semiconductor devices. We also obtain alloptical non-return-to-zero to return-to-zero (NRZ-to-RZ) format conversion using the recovered clock signal at 10 Gbps and 40 Gbps. It leads to a good performance using a Mach-Zehnder interferometric wavelength converter and a self-pulsating laser diode (LD). The self-pulsating LD serves a recovered clock, which has an rms timing jitter as low as sub-picosecond. In the case of 3R regeneration of RZ data, we achieve a 1.0 dB power penalty at $10^{-9}$ BER after demultiplexing 40 Gbps to 10 Gbps with an eletroabsorption modulator. The regenerated 3R data shows stable error-free operation with no BER floor for all channels. The combination of these functional devices provides all-optical 3R regeneration with NRZ-to-RZ conversion.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.11
• /
• pp.79-85
• /
• 2004

A digitally-controlled analog-block inevitably undergoes the bang-bang oscillations which may cause a big amplitudes of the glitches if the oscillation occurs at the MSB transition points of a binary counter. The glitch results into the jitter noise for the case of the DLL. In this paper, we devise a new counter code that has the hysteresis in the bit transitions in order to prevent the transitions of the significant counter-bits at the locking state. The maximum clock jitter is simulated to considerably reduce over the voltage-temperature range guaranteed by specifications. The counter is employed to implement the high speed packet-base DRAM and contributes to the maximized valid data-window.

• ETRI Journal
• /
• v.32 no.6
• /
• pp.911-920
• /
• 2010

This paper presents a method of designing hybrid analog/asymmetrical square-root (SR) FIR filters. In addition to the conventional frequency domain constraints, the proposed method considers time-domain constraints as well, including the inter-symbol interference (ISI) and the opening of the eye pattern at the receiver output. This paper also reviews a systematic way to find the discrete-time equivalence of analog parts in a band-limited digital communication system. Thus, a phase equalizer can be easily realized to compensate for the nonlinear phase responses of the analog components. With the hybrid analog/SR FIR filter co-design, examples show that using the proposed method can result in a more robust ISI performance in the presence of the receiver clock jitter.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.3
• /
• pp.200-209
• /
• 2008

This paper describes bandwidth linearization techniques in phase-locked loop (PLL) design for common-clock serial link applications. Utilizing a continuously tunable single-input dual-path LC VCO and a constant-gain phase detector, a proposed architecture is well suited to implementing PLLs that must be compliant with standards that specify minimum and maximum allowable bandwidths such as PCI Express Gen2 or FB-DIMM applications. A prototype 4.75 to 6.1-GHz PLL is implemented in 90-nm CMOS. Measurement results show that the PLL bandwidth and random jitter (RJ) variations are well regulated and that the use of a differentially controlled dual-path VCO is important for deterministic jitter (DJ) performance.

• Journal of Sensor Science and Technology
• /
• v.19 no.6
• /
• pp.469-474
• /
• 2010

This paper presents a 10Gbps CMOS parallel-to-serial converter for transmission of sensor data. A low-noise clock multiplying unit(CMU) and a multiplexer with controllable data sequence are proposed. The transmitter was fabricated in 0.13 um CMOS process and the measured total output jitter was less than 0.1 UIpp(unit-interval, peak-to-peak) over 20 kHz to 80 MHz bandwidth. The jitter of the CMU output only was measured as 0.2 ps,rms. The transmitter dissipates less than 200 mW from 1.5 V/2.5 V power supplies.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.7
• /
• pp.1877-1883
• /
• 1999

Synchronization of the clock at the ATM receiving terminal is studied. The technique analyzed here has been adapted by ITU-T as the standard for ATM timing recovery. This paper presents analysis of SRTS method itself and jitter in SRTS. The power pectrum and rms amplitude of SRTS jitter are calculated. The calculated average rms value for T1 1.544MHz source signal is 32.63ns and 0.15ns for E4 139.264MHz signal.