• 한국전기전자재료학회논문지
• /
• 제23권4호
• /
• pp.293-297
• /
• 2010

We have studied the optical and electrical properties of a-IGZO thin films on the n-type semiconductor fabricated by RF magnetron sputtering method. The ceramic target was used in which $In_2O_3$, $Ga_2O_3$ and ZnO powder were mixed with 1:1:2 mol% ratio and furnished. The RF power was set at 25 W, 50 W, 75 W and 100 W as a variable process condition. The transmittance of the films in the visible range was above 80%, and it was 92% in the case of 25 W power. AFM analysis showed that the roughness increased as increasing RF power, and XRD showed amorphous structure of the films without any peak. The films are electrically characterized by high mobility above 10 $cm^2/V{\cdot}s$ at low RF power, high carrier concentration and low resistivity. It is required to study further finding the optimal process condition such as lowering the RF power, prolonging the deposition ratio and qualification analysis.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1010-1013
• /
• 2006

To understand the exact charge carrier photogeneration properties of photoactive thin films consisting of a ${\pi}-conjugated$ polymer matrix and a triplet dopant, we prepared two types of polymer, poly(9-vinylcarbazole) (PVK) and poly[9,9-bis(2- ethylhexyl)fluorene-2,7-diyl] (PF2/6) doped with triplet emitters for organic light-emitting diodes (OLED), either iridium(III)fac-tris(2-phenylpyridine) $(Ir(ppy)_3)$ or iridium(III)bis[(4,6-fluorophenyl)- $pyridinato-N,C^2'$]picolinate (FIrpic), as thin film devices by using the conventional method. Those doped film devices, as well as pristine film devices, on ITO substrates were characterized by means of steady state photocurrent measurement for a wide spectral range.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.354-354
• /
• 2007

Titanium nitride (TiN) thin films are widely used for hard coatings due to their superior hardness. In this paper, we wanted see how the films properties are changed according to DC power. TiN thin films were deposited by direct current (DC) magnetron sputtering method using TiN compound target on silicon substrates. The films structural properties are examined by X-ray Diffractions (XRD) and tribological properties are measured by nano-indentation, nano-scratch tester, nano-stress tester. Especially in DC power of 150 W, the maximum hardness and the minimum residual stress of TiN film exhibited about 25 GPa and 1 GPa, respectively. And also, the critical load of TiN film prepared by magnetron sputtering method were measured over 30 N.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권10호
• /
• pp.436-440
• /
• 2003

The (S $r_{0.85}$C $a_{0.15}$)Ti $O_3$(SCT) thin films were deposited on Pt-coated electrode(Pt/TiN/ $SiO_2$/Si) using RF sputtering method according to the deposition condition. The optimum conditions of RF power and Ar/ $O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin films was about 18.75[$\AA$/min] at the optimum condition. The composition of SCT thin films deposited on Si substrate is close to stoichiometry (1.102 in A/B ratio). The capacitance characteristics had a stable value within $\pm$4[%]. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films were observed above 200[kHz]. SCT thin films used in this study showed the phenomena of dielectric relaxation with the increase of frequency.ncy.

• 반도체디스플레이기술학회지
• /
• 제11권4호
• /
• pp.19-23
• /
• 2012

We report microbolometer characteristic with n-type and p-type amorphous silicon thin film. The n-type and p-type amorphous silicon thin films were made by PECVD. The electrical properties of n-type and p-type a-Si:H thin films were investigated as a function of doping gas flow rate. The doping gas used $B_2H_6/Ar$ (1:9) and $PH_3/Ar$ (1:9). In general, the conductivity of doping a-Si:H thin films increased as doping gas increase but the conductivity of a-Si:H thin films decreased as the doping gas increase because doping gas concentration increase led to dilution gas (Ar) increase as the same time. We fabricated an amorphous silicon microbolometer using surface micromachining technology. The fabricated microbolometer had a negative TCR of 2.3%. The p-type microbolometer had responsivity of $5{\times}10^4V/W$ and high detectivity of $3{\times}10^8cm(Hz)^{1/2}/W$. The p-type microbolometer had more detectivity than n-type for less noise value.

• 센서학회지
• /
• 제29권5호
• /
• pp.328-331
• /
• 2020

In this study, a highly crystalline SnO₂ thin film was formed using a sol-gel process. In addition, a SnO₂ thin-film transistor was successfully fabricated. The fabricated SnO₂ thin-film transistor exhibited conventional n-type semiconductor properties, with a mobility of 0.1 cm² V^-1 s^-1, an on/off current ratio of 1.2 × 10⁵, and a subthreshold swing of 2.69. The formed SnO₂ had a larger bandgap (3.95 eV) owing to the bandgap broadening effect. The fabricated photosensor exhibited a responsivity of 1.4 × 10^-6 Jones, gain of 1.43 × 10⁷, detectivity of 2.75 × 10^-6 cm Hz^1/2 W^-1, and photosensitivity of 4.67 × 10².

• 열처리공학회지
• /
• 제18권4호
• /
• pp.229-234
• /
• 2005

Effect of incident ion beam energy on microstructure and adhesion behavior of TiN thin films were studied. Without ion beam assist, TiN film showed (111) growth mode which was thought to have the lowest deformation energy. As the ion beam assist energy increased, TiN film growth mode was changed from (111) to (200) mode. On the Si(100) substrate the critical incident energy for growth mode change was 100 eV/atom, however the critical assist energy was 121 eV/atom on the STD61 substrate. Grain size of TiN films increased with the assist ion beam energy. Finally, adhesion strength of TiN films bombarded above the critical ion assist energy showed 4~5 times higher values than that with lower bombard ion energy.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.509-512
• /
• 2001

Aluminum nitride(AlN) thin films were deposited on silicon substrates using RF magnetron sputtering at various deposition conditions and investigated the characteristics. It was used XRD, AES, SEM, and HP-4145B semiconductor parameter analyzer to analysis deposited AlN thin films. The deposition conditions for the good c-axis orientation were 100 W of RF power, $200^{\circ}C$ of substrate temperature and 15 mTorr of working pressure. The leakage current density was less then $1.3{\times}10^{-7}A/cm^{2}$. And it was also investigated the etching properties of deposited AlN thin films for application.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1459-1462
• /
• 2007

In general a thermoelectric cooler (TEC) consists of a series of P type and N type thermoelectric materials sandwiched between two wafers. When a DC current passes through these materials, three different effects take place; Peltier effect, Joule heating effect and heat transfer by conduction due to temperature difference between hot and cold plates. In this study we have developed a micro TEC using $Bi_2Te_3$ (N type) and $Bi_{0.5}Sb_{1.5}Te_3$ (P type) thin films. In order to improve that performance of a micro TEC, we made 10 um height TE legs using special PR only for lift-off. We measured COP (coefficient of performance) and temperature difference between hot and cold connectors with current.

• 한국정보통신학회논문지
• /
• 제4권3호
• /
• pp.705-711
• /
• 2000

반도체 제조공정과 미세가공 기술을 이용하여 $300^{\circ}C$의 동작온도에서 약 60 mW의 전력소모를 갖는 산화물 반도체 박막 가스센서 어레이를 제조하였다. 멤브레인의 우수한 열적 절연은 $0.1\mum\; 두께의\; Si_3N_4와\; 1\mum$ 두께의 PSG의 이중 층에 의한 것으로, 각각 LPCVD(저압화학 기상증착)와 APCVD(대기압 화학 기상증착)에 의해 제조되었다. 센서 어레이의 4가지 산화물 반도체 박막 감지물질로는 1 wt.% Pd가 도핑된 $SnO_2,\; 6 we.% A1_2O_3$가 도핑된 ZnO, $WO_3$, ZnO를 이용하였으며,4가지 감지물질의 베이스라인 저항은 $300^{\circ}C$ 에서 3일 동안의 에이징을 거친 후 안정됨을 보였다. 제조된 초소형 산화물 반도체 박막 가스센서 어레이는 여러 가지 가스의 노출 시 유용한 저항 변화를 나타내었으며 감도는 감지 물질에 강하게 의존함을 알 수 있었다.