• Journal of Welding and Joining
• /
• 제32권3호
• /
• pp.19-26
• /
• 2014

Through Silicon Via (TSV) technology is the shortest interconnection technology which is compared with conventional wire bonding interconnection technology. Recently, this technology has been also noticed for the miniaturization of electronic devices, multi-functional and high performance. The short interconnection length of TSV achieve can implement a high density and power efficiency. Among the TSV technology, TSV filling process is important technology because the cost of TSV technology is depended on the filling process time and reliability. Various filling methods have been developed like as Cu electroplating method, molten solder insert method and Ti/W deposition method. In this paper, various TSV filling methods were introduced and each filling materials were discussed.

• Journal of Welding and Joining
• /
• 제32권3호
• /
• pp.11-18
• /
• 2014

TSV(through silicon via) filling technology is making a hole in Si wafer and electrically connecting technique between front and back of Si die by filling with conductive metal. This technology allows that a three-dimensionally connected Si die can make without a large number of wire-bonding. These TSV technologies require various engineering skills such as forming a via hole, forming a functional thin film, filling a conductive metal, polishing a wafer, chip stacking and TSV reliability analysis. This paper addresses the TSV filling using Cu electrodeposition. The impact of plating conditions with additives and current density on electrodeposition will be considered. There are additives such as accelerator, inhibitor, leveler, etc. suitably controlling the amount of the additive is important. Also, in order to fill conductive material in whole TSV hole, current wave forms such as PR(pulse reverse), PPR(periodic pulse reverse) are used. This study about semiconductor packaging will be able to contribute to the commercialization of 3D TSV technology.

• 한국재료학회지
• /
• 제22권7호
• /
• pp.335-341
• /
• 2012

Recently, the demand for the miniaturization of printed circuit boards has been increasing, as electronic devices have been sharply downsized. Conventional multi-layered PCBs are limited in terms their use with higher packaging densities. Therefore, a build-up process has been adopted as a new multi-layered PCB manufacturing process. In this process, via-holes are used to connect each conductive layer. After the connection of the interlayers created by electro copper plating, the via-holes are filled with a conductive paste. In this study, a desmear treatment, electroless plating and electroplating were carried out to investigate the optimum processing conditions for Cu via filling on a PCB. The desmear treatment involved swelling, etching, reduction, and an acid dip. A seed layer was formed on the via surface by electroless Cu plating. For Cu via filling, the electroplating of Cu from an acid sulfate bath containing typical additives such as PEG(polyethylene glycol), chloride ions, bis-(3-sodiumsulfopropyl disulfide) (SPS), and Janus Green B(JGB) was carried out. The desmear treatment clearly removes laser drilling residue and improves the surface roughness, which is necessary to ensure good adhesion of the Cu. A homogeneous and thick Cu seed layer was deposited on the samples after the desmear treatment. The 2,2'-Dipyridyl additive significantly improves the seed layer quality. SPS, PEG, and JGB additives are necessary to ensure defect-free bottom-up super filling.

• 한국재료학회지
• /
• 제23권10호
• /
• pp.550-554
• /
• 2013

As continued scaling becomes increasingly difficult, 3D integration has emerged as a viable solution to achieve higher bandwidths and good power efficiency. 3D integration can be defined as a technology involving the stacking of multiple processed wafers containing integrated circuits on top of each other with vertical interconnects between the wafers. This type of 3D structure can improve performance levels, enable the integration of devices with incompatible process flows, and reduce form factors. Through silicon vias (TSVs), which directly connect stacked structures die-to-die, are an enabling technology for future 3D integrated systems. TSVs filled with copper using an electro-plating method are investigated in this study. DC and pulses are used as a current source for the electro-plating process as a means of via filling. A TiN barrier and Ru seed layers are deposited by plasma-enhanced atomic layer deposition (PEALD) with thicknesses of 10 and 30 nm, respectively. All samples electroplated by the DC current showed defects, even with additives. However, the samples electroplated by the pulse current showed defect-free super-filled via structures. The optimized condition for defect-free bottom-up super-filling was established by adjusting the additive concentrations in the basic plating solution of copper sulfate. The optimized concentrations of JGB and SPS were found to be 10 and 20 ppm, respectively.

• Journal of Welding and Joining
• /
• 제32권3호
• /
• pp.68-73
• /
• 2014

Among through silicon via (TSV) technologies, for replacing Cu filling method, the method of molten solder filling has been proposed to reduce filling cost and filling time. However, because Sn alloy which has a high coefficient of thermal expansion (CTE) than Cu, CTE mismatch between Si and molten solder induced higher thermal stress than Cu filling method. This thermal stress can deteriorate reliability of TSV by forming defects like void, crack and so on. Therefore, we fabricated SiC composite filling material which had a low CTE for reducing thermal stress in TSV. To add SiC nano particles to molten solder, ball-typed SiC clusters, which were formed with Sn powders and SiC nano particles by ball mill process, put into molten Sn and then, nano particle-dispersed SiC composite filling material was produced. In the case of 1 wt.% of SiC particle, the CTE showed a lowest value which was a $14.8ppm/^{\circ}C$ and this value was lower than CTE of Cu. Up to 1 wt.% of SiC particle, Young's modulus increased as wt.% of SiC particle increased. And also, we observed cross-sectioned TSV which was filled with 1 wt.% of SiC particle and we confirmed a possibility of SiC composite material as a TSV filling material.

• Journal of Welding and Joining
• /
• 제31권3호
• /
• pp.11-16
• /
• 2013

Through-silicon-via (TSV) is a major technology in microelectronics for three dimensional high density packaging. The 3-dimensional TSV technology is applied to CMOS sensors, MEMS, HB-LED modules, stacked memories, power and analog, SIP and so on which can be employed to car electronics. The copper electroplating is widely used in the TSV filling process. In this paper, the various Cu filling methods using the control of the plating process were described in detail including recent studies. Via filling behavior by each method was also introduced.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.75-75
• /
• 2010

3D 패키징 기술은 전기소자의 소형화, 고용량화, 저전력화, 높은 신뢰성등의 요구와 함께 그 중요성이 대두대고 있다. 이러한 3D 패키징의 연결방법은 와이어 본딩 또는 플립칩등의 기존의 방법에서 TSV(Through Silicon Via)를 이용하여 적층하는 방법이 주목받고 있다. TSV는 기존의 와이어 본딩과 비교하여 고집적도, 빠른 신호전달, 낮은 전력소비 등의 장점을 가지고 있어 많은 연구가 진행되고 있다. TSV의 세부 공정 중 비아필링(Via filling)기술은 I/O수 증가와 미세피치화에 따른 비아(Via) 직경의 감소 및 종횡비(Via Aspect Ratio)증가로 인해 기존 필링 공정으로는 한계가 있다. 기존의 비아 홀(Via hole)에 금속을 필링하기 위한 방법으로 전기도금법이 많이 사용되고 있으나, 전기도금법은 전기도금액 조성, 첨가제의 종류, 전류밀도, 전류모드 등에 따라 결과물에 큰 차이가 발생되어, 최적공정조건의 도출이 어렵다. 또한 20um이하의 비아직경과 높은 종횡비로 인하여 충진시 void형성등의 문제점이 발생하기도 한다. 본 연구에서는 용융솔더와 진공을 이용하여 비아를 필링시켰다. 이 방법은 관통된 비아가 형성된 웨이퍼 양단에 압력차를 주어, 작은 직경을 갖는 비아 홀의 표면장력을 극복하고, 용융상태의 솔더가 관통된 비아 홀 내부로 필링되는 방법이다. 관통 비아홀이 형성 된 웨이퍼 위에 솔더페이스트를 $250^{\circ}C$이상 온도를 가해 용융상태로 만든 후 웨이퍼 하부에 진공을 형성하여 필링하는 방법과 용융솔더를 노즐을 통하여 위쪽으로 유동시켜 그 위에 비아홀이 형성된 웨이퍼를 접촉하고 웨이퍼 상부에 진공을 형성하여 필링하는 방법으로 실험을 각각 실시하였다. 이 때, 웨이퍼 두께는 100um이하이며 홀 직경은 20, 30um, 웨이퍼 상부와 하부의 진공차는 약 0.02~0.08Mpa, 진공 유지시간은 1~3s로 실시하여 최적 조건을 고찰하였다. 각 조건에 따른 필링 후 단면을 전자현미경(FE-SEM)을 통해 관찰하였다. 실험 결과 0.04Mpa 이상에서 1s내의 시간에 모든 비아홀이 기공(Void)없이 완벽하게 필링되는 것을 관찰하였으며 이 결과는 기존의 방법에 비하여 공정시간을 감소시켜 생산성이 대폭 향상 될 수 있는 방법임을 확인하였다.

• Korean Chemical Engineering Research
• /
• 제54권6호
• /
• pp.723-733
• /
• 2016

반도체 배선 미세화에 의한 한계를 극복하기 위해 실리콘 관통 비아(through silicon via, TSV)를 사용한 소자의 3차원 적층에 대한 연구가 진행되고 있다. TSV 내부는 전해도금을 통해 구리로 채우며, 소자의 신뢰성을 확보하기 위해 결함 없는 TSV의 채움이 요구된다. TSV 입구와 벽면에서는 구리 전착을 억제하고, TSV 바닥에서 선택적으로 구리 전착을 유도하는 바닥 차오름을 통해 무결함 채움이 가능하다. 전해 도금액에 포함되는 유기 첨가제는 TSV 위치에 따라 국부적으로 구리 전착 속도를 결정하여 무결함 채움을 가능하게 한다. TSV의 채움 메커니즘은 첨가제의 거동에 기반하여 규명되므로 첨가제의 특성을 이해하는 연구가 선행되어야 한다. 본 총설에서는 첨가제의 작용기작을 바탕으로 하는 다양한 채움 메커니즘, TSV 채움 효율을 개선하기 위한 평탄제의 개발과 3-첨가제 시스템에서의 연구, 첨가제 작용기와 도금 방법의 수정을 통한 채움 특성의 향상에 관한 연구를 소개한다.

• 마이크로전자및패키징학회지
• /
• 제21권4호
• /
• pp.91-96
• /
• 2014

TSV기술은 실리콘 칩에 관통 홀(through silicon via)을 형성하고, 비아 내부에 전도성 금속으로 채워 수직으로 쌓아 올려 칩의 집적도를 향상시키는 3차원 패키징 기술로서, 와이어 본딩(wire bonding)방식으로 접속하는 기존의 방식에 비해 배선의 거리를 크게 단축시킬 수 있다. 이를 통해 빠른 처리 속도, 낮은 소비전력, 높은 소자밀도를 얻을 수 있다. 본 연구에서는 웨이퍼 레벨에서의 TSV 충전 경향을 조사하기 위하여, 실리콘의 칩 레벨에서부터 4" 웨이퍼까지 전해 도금법을 이용하여 Cu를 충전하였다. Cu 충전을 위한 도금액은 CuSO4 5H2O, H2SO4 와 소량의 첨가제로 구성하였다. 양극은 Pt를 사용하였으며, 음극은 $0.5{\times}0.5 cm^2{\sim}5{\times}5cm^2$ 실리콘 칩과 4" 실리콘 wafer를 사용하였다. 실험 결과, $0.5{\times}0.5cm^2$ 실리콘 칩을 이용하여 양극과 음극과의 거리에 따라 충전률을 비교하여 전극간 거리가 4 cm일 때 충전률이 가장 양호하였다. $5{\times}5cm^2$ 실리콘 칩의 경우, 전류 공급위치로부터 0~0.5 cm 거리에 위치한 TSV의 경우 100%의 Cu충전률을 보였고, 4.5~5 cm 거리에 위치한 TSV의 경우 충전률이 약 95%로 비아의 입구 부분이 완전히 충전되지 않는 경향을 보였다. 전극에서 멀리 떨어져있는 TSV에서 Cu 충전률이 감소하였으며, 안정된 충전을 위하여 전류를 인가하는 시간을 2 hrs에서 2.5 hrs로 증가시켜 4" 웨이퍼에서 양호한 TSV 충전을 할 수 있었다.

• Journal of Welding and Joining
• /
• 제24권2호
• /
• pp.64-70
• /
• 2006

The 3-dimensional (3D) chip stacking technology is a leading technology to realize a high density and high performance system in package (SiP). There are several kinds of methods for chip stacking, but the stacking and interconnection through Cu filled through-hole via is considered to be one of the most advanced stacking technologies. Therefore, we studied the optimum process of through-hole via formation and Cu filling process for Si wafer stacking. Through-hole via was formed with DRIE (Deep Reactive ion Etching) and Cu filling was realized with the electroplating method. The optimized conditions for the via formation were RE coil power of 200 W, etch/passivation cycle time of 6.5 : 6 s and SF6 : C4F8 gas flow rate of 260 : 100 sccm. The reverse pulsed current of 1.5 A/dm2 was the most favorable condition for the Cu electroplating in the via. The Cu filled Si wafer was chemically and mechanically polished (CMP) for the following flip chip bumping technology.