• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.185-188
• /
• 2002

In this paper, Amorphous silicon on glass substrate was recrytallized to poly-crystalline silicon by solid phase crystallization(SPC) technology The active region of thin film transistor(TFT) was fabricated by amorphous silicon. The output and transfer characteristics of thin film transistor with lightly doped drain(LDD) structure was measured and analyzed. As a results, analyzed TFT's reliability with LDD's length by various kinds argument such as sub-threshold swing coefficient, mobility and threshold voltages were evaluated. Stress effects in TFT were able to improve to the characteristics of turn-on current and hot carrier effects by LDD's length variations

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.2
• /
• pp.112-115
• /
• 2011

To stabilize the electric characteristic of Silicon Thin Film Transistor, reducing the current leakage is most important issue. To reduce the current leakage, many ideas were suggested. But the increase of mask layer also increased the cost. On this research Bird's Beak process was use to present element. Using Silvaco simulator, it was proven that it was able to reduce current leakage without mask layer. As a result, it was possible to suggest the structure that can reduce the current leakage to 1.39nA without having mask layer increase. Also, I was able to lead the result that electric characteristic (on/off current ratio) was improved compare from conventional structure.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.535-542
• /
• 1998

SOI(silicon oninsulator) was fabricated through the direct bonding of a hydrophilized single crystal Si wafer and a thermally oxidized SiO2 thin film to investigate the stacking faults in silicon at the Si/SiO2 in-terface. At first the oxidation kinetics of SiO2 thin film and the stacking fault distribution at the oxidation interface were investigated. The stacking faults could be divided into two groups by their size and the small-er ones were incorporated into the larger ones as the oxidation time and temperature increased. The den-sity of the smaller ones based critically lower eventually. The SOI wafers directly bonded at the room temperature were annealed at 120$0^{\circ}C$ for 1 hour. The stacking faults at the bonding and oxidation interface were examined and there were anomalies in the distributions of the stacking faults of the bonded region to arrange in ordered ring-like fashion.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.4
• /
• pp.568-573
• /
• 1996

The amorphous silicon films deposited by low pressure chemical vapor deposition are crystallized by the various annealing techniques including low-temperature furnace annealing and two-step annealing. Two-step annealing is the combination of furnace annealing at 600 [.deg. C] for 24 h and the sequential furnace annealing at 950 [.deg. C] 1h or the excimer laser annealing. It s found that two-step annealings reduce the in-grain defects significantly without changing the grain boundary structure. The performance of the poly-Si thin film transistors (TFTs) produced by employing the tow-step annealing has been improved significantly compared with those of one-step annealing. (author). 13 refs., 6 figs., 1 tab.

• Journal of the Korean Solar Energy Society
• /
• v.28 no.4
• /
• pp.62-67
• /
• 2008

In this study, we analyze the electrical characteristics of amorphous silicon thin film photovoltaic module which are installed about 5 years ago. Four modules from PV system are extracted and measured the maximum power change ratio using solar simulator(Class A). Also, infrared camera is used to get thermal distribution characteristics of system. The external appearance change is compared with initial module by naked eye examination. Through this experiment, 31% maximum output power drop is observed. The detail description is specified as the following paper.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.117-123
• /
• 2014

The fabrication and characterization of a Si/ZnO thin film heterojunction ultraviolet photodiode has been presented in this paper. ZnO thin film of ~100 nm thick was deposited on <100> Silicon (Si) wafer by atomic layer deposition (ALD) technique. The Photoluminescence spectroscopy confirms that as-deposited ZnO thin film has excellent visible-blind UV response with almost no defects in the visible region. The room temperature current-voltage characteristics of the n-ZnO thin film/p-Si photodiodes are measured under an UV illumination of $650{\mu}W$ at 365 nm in the applied voltage range of ${\pm}2V$. The current-voltage characteristics demonstrate an excellent UV photoresponse of the device in its reverse bias operation with a contrast ratio of ~ 1115 and responsivity of ~0.075 A/W at 2 V reverse bias voltage.

• Current Photovoltaic Research
• /
• v.2 no.2
• /
• pp.41-47
• /
• 2014

Extensive investigation on silicon based thin film reveals a wide range of film characteristics, from low optical gap to high optical gap, from amorphous to micro-crystalline silicon etc. Fabrication of single junction, tandem and triple junction solar cell with suitable materials, indicate that fabrication of solar cell of a relatively moderate efficiency is possible with a better light induced stability. Due to these investigations, various competing materials like wide band gap silicon carbide and silicon oxide, low band gap micro-crystalline silicon and silicon germanium etc were also prepared and applied to the solar cells. Such a multi-junction solar cell can be a technologically promising photo-voltaic device, as the external quantum efficiency of such a cell covers a wider spectral range.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.1
• /
• pp.57-62
• /
• 1999

Polycrystaline thin film transistors are fabricated on the transparent glass substrate by a lamp-scan annealing. The line-shaped lamp scanning method, which is profitable for large area process, effectively radiated silicon film on glass substrate. Amorphous silion film absorbs the light which is emitted from halogen-lamp and it transformed into crystalline silicon by metal-induced lateral crystallization. In order to enhance the annealing effect, capping layer was deposited on the whole substrate. When the scan speed was 1-2mm/sec, lateral crystallization of amorphous silicon under capping layer was 18~27${\mu}m/scan$. The thin film transistor fabricated by this method shows high electron mobility over 130$cm^2/V{\cdot}sec$

• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.341-346
• /
• 2011

In this study, we inserted a Zn buffer layer into a AZO/p-type a-si:H layer interface in order to lower the contact resistance of the interface. For the Zn layer, the deposition was conducted at 5 nm, 7 nm and 10 nm using the rf-magnetron sputtering method. The results were compared to that of the AZO film to discuss the possibility of the Zn layer being used as a transparent conductive oxide thin film for application in the silicon heterojunction solar cell. We used the rf-magnetron sputtering method to fabricate Al 2 wt.% of Al-doped ZnO (AZO) film as a transparent conductive oxide (TCO). We analyzed the electro-optical properties of the ZnO as well as the interface properties of the AZO/p-type a-Si:H layer. After inserting a buffer layer into the AZO/p-type a-Si:H layers to enhance the interface properties, we measured the contact resistance of the layers using a CTLM (circular transmission line model) pattern, the depth profile of the layers using AES (auger electron spectroscopy), and the changes in the properties of the AZO thin film through heat treatment. We investigated the effects of the interface properties of the AZO/p-type a-Si:H layer on the characteristics of silicon heterojunction solar cells and the way to improve the interface properties. When depositing AZO thin film on a-Si layer, oxygen atoms are diffused from the AZO thin film towards the a-Si layer. Thus, the characteristics of the solar cells deteriorate due to the created oxide film. While a diffusion of Zn occurs toward the a-Si in the case of AZO used as TCO, the diffusion of In occurs toward a-Si in the case of ITO used as TCO.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.113-116
• /
• 2005

In this paper, silicon thin-film solar cells(Si- TFSC) and a-Si/c-Si heterojunction solar cells(HJ-cell) are investigated. The Si-TFSC was prepared on glass substrate by depositing $1-3{\mu}m$ thin-film silicons by glow discharge method. The $a-Si:H/{\mu}c-Si:H$ tandem solar cells on textured ZnO:A1 TCO (transparent conducting oxide) showed improved Jsc in top and bottom cells than that on $SnO_2:F$ TCO. This enhancement of jsc resulted from improved light trapping effect by front textured ZnO:A1. The a-Si/c-Si HJ-cells with simple structure without high efficiency features are suffering from low Voc and Jsc. The improvement of front nip and back interface properties by adopting high quality silicon-films at low temperature should be done both for increasing device performances and production cost.