• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.4
• /
• pp.913-920
• /
• 2011

In this paper, a logic process based 1-kbit EEPROM IP for RFID tag chips of 900MHz is designed. The cell array of the designed 1-kbit EEPROM IP is arranged in a form of four blocks of 16 rows x 16 columns, that is in a two-dimensional arrangement of one-word EEPROM phantom cells. We can reduce the IP size by making four memory blocks share CG (control gate) and TG (tunnel gate) driver circuits. We propose a TG switch circuit to supply respective TG bias voltages according to operational modes and to keep voltages between devices within 5.5V in terms of reliability in order to share the TG driver circuit. Also, we can reduce the power consumption in the read mode by using a partial activation method to activate just one of four memory blocks. Furthermore, we can reduce the access time by making BL (bit line) switching times faster in the read mode from reduced number of cells connected to each column. We design and compare two 1-kbit EEPROM IPs, two blocks of 32 rows ${\times}$ 16 columns and four blocks of 16 rows ${\times}$ 16 columns, which use Tower's $0.18{\mu}m$ CMOS process. The four-block IP is smaller by 11.9% in the layout size and by 51% in the power consumption in the read mode than the two-block counterpart.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.10
• /
• pp.2337-2342
• /
• 2010

There is a vast field of application for RFID(Radio Frequency IDentification) technology. In the case of hospitals, RFID can be used for organizing patient data. Generally, patient data has been handled with medical cards. In order to look up data about a patient, the medical card would have to be found first, within a lot of other medical cards, by hand or with a computer. This is a very inconvenient system. Also, if the card is searched by the name of the patient, fatal medical accidents may occur in cases of mix-ups. If remote RFID Tag monitoring systems are applied in this case, the patient data would be accessible in the hospital. This article will discuss the grafting of RFID systems and wireless data communicating technology. The EM4095 chip, which uses 125KHz carrier waves was used in this study. And a Bluetooth module was added for wireless data communication. The ATMEGA128 microcomputer was used to control the RFID system and wireless module. A LCD monitor was connected to the extension port for nurses to view patient data, and also, the same information was displayed on PC monitors for doctors to see. The circuit was designed to consume minimal amounts of electricity for portability, and to transmit Tag ID's in environments with a lot of noise. The article is concluded with a diagram of the whole system, and performance of each data transmitting section has been analyzed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.3
• /
• pp.486-495
• /
• 2006

In this paper, a low-power 1Kb synchronous EEPROM is designed with flash cells for passive UHF RFID tag chips. To make a low-power EEPROM, four techniques are newly proposed. Firstly, dual power supply voltages VDD(1.5V) and VDDP(2.5V), are used. Secondly, CKE signal is used to remove switching current due to clocking of synchronous circuits. Thirdly, a low-speed but low-power sensing scheme using clocked inverters is used instead of the conventional current sensing method. Lastly, the low-voltage, VDD for the reference voltage generator is supplied by using the Voltage-up converter in write cycle. An EEPROM is fabricated with the $0.25{\mu}m$ EEPROM process. Simulation results show that power dissipations are $4.25{\mu}W$ in the read cycle and $25{\mu}W$ in the write cycle, respectively. The layout area is $646.3\times657.68{\mu}m^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2366-2373
• /
• 2007

In this paper, a low-power and small-area asynchronous 1 kilobit EEPROM for passive UHF RFID tag chips is designed with $0.18{\mu}m$ EEPROM cells. As small area solutions, command and address buffers are removed since we design asynchronous I/O interface and data output buffer is also removed by using separate I/O. To supply stably high voltages VPP and VPPL used in the cell array from low voltage VDD, Dickson charge pump is designed with schottky diodes instead of a PN junction diodes. On that account, we can decrease the number of stages of the charge pump, which can decrease layout area of charge pump. As a low-power solution, we can reduce write current by using the proposed VPPL power switching circuit which selects each needed voltage at either program or write mode. A test chip of asynchronous 1 kilobit EEPROM is fabricated, and its layout area is $554.8{\times}306.9{\mu}m2$., 11% smaller than its synchronous counterpart.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.1
• /
• pp.46-52
• /
• 2014

In this paper, we present a design of meander type microstrip patch antenna which has the best quality in RFID approved international standard of 910MHz broadband, usable in metal environment. In order to be fit into the commercial tag chip on the antenna, a square shaped feeder is installed on the main body as well as in the main body. In addition, a multi meander type patching element was designed in order to reduce the main body effectively. Three antennae, Cases 1, 2 and 3, were designed and compared in the areas of broad band width, effectiveness or recognition distance according to their sizes and number of folds. The measurement result of Case 3 was determined to be the best. It was confirmed that mostly the efficiency and characteristic gain change due to antenna size and number of folds in meander type influenced the antenna recognition distance.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.5
• /
• pp.628-635
• /
• 2018

Objective: To determine the effects of genomic breeding values (GBV) and single nucleotide polymorphisms (SNP) on the total number of piglets born (TNB) in 3 pig breeds (Berkshire, Landrace, and Yorkshire). Methods: After collecting genomic information (Porcine SNP BeadChip) and phenotypic TNB records for each breed, the effects of GBV and SNP were estimated by using single step best linear unbiased prediction (ssBLUP) method. Results: The heritability estimates for TNB in Berkshire, Landrace, and Yorkshire breeds were 0.078, 0.107, and 0.121, respectively. The breeding value estimates for TNB in Berkshire, Landrace, and Yorkshire breeds were in the range of -1.34 to 1.47 heads, -1.79 to 1.87 heads, and -2.60 to 2.94 heads, respectively. Of sows having records for TNB, the reliability of breeding value for individuals with SNP information was higher than that for individuals without SNP information. Distributions of the SNP effects on TNB did not follow gamma distribution. Most SNP effects were near zero. Only a few SNPs had large effects. The numbers of SNPs with absolute value of more than 4 standard deviations in Berkshire, Landrace, and Yorkshire breeds were 11, 8, and 19, respectively. There was no SNP with absolute value of more than 5 standard deviations in Berkshire or Landrace. However, in Yorkshire, four SNPs (ASGA 0089457, ASGA0103374, ALGA0111816, and ALGA0098882) had absolute values of more than 5 standard deviations. Conclusion: There was no common SNP with large effect among breeds. This might be due to the large genetic composition differences and the small size of reference population. For the precise evaluation of genetic performance of individuals using a genomic selection method, it may be necessary to establish the appropriate size of reference population.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.8
• /
• pp.185-194
• /
• 2014

In this paper, we proposed the clothing management system using the smart hanger. Proposed system consists of smart hanger, base module, and server, and the smart hanger consists of MCU, LED, RFID reader, RF chip, ring sensor, and battery. The smart hanger reads the RFID tag attached to the clothes and wirelessly transmitted to the server. The server associated base module communicates with the smart hanger and transmits information to the server. The server manages clothing through the DB, and can display various information through the web page and the smart phone. In order to verify the usefulness of the proposed system, we did experiment with the management system for clothing store and laundry where using a lot of hangers. Performance tests of the smart hanger are applied to check the current consumption and can be predicted the battery life with the proposed low power algorithm. The clothing store management system can be increased sales and convenience of the consumer. The laundry management system can be increased the efficiency of laundry category and convenience of the consumer.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.7
• /
• pp.1510-1516
• /
• 2011

As emergence of the ubiquitous society, it is possible to access the network for services needed to us in anytime and anywhere. The phenomena has been accelerated by revitalization of the sensor network offering the sensing information and data. Currently, sensor network contributes the convenience for various services such as environment monitoring, health care and home automation. However, sensor network has a weak point compared to traditional network, which is easily exposed to attacker. For this reason, messages communicated over the sensor network, are encrypted with symmetric key and transmitted. A number of symmetric cryptography algorithms have been researched. Among of them HIGHT algorithm in hardware and software implementation are more efficient than tradition AES in terms of speed and chip size. Therefore, it is suitable to resource constrained devices including RFID tag, Sensor node and Smart card. In the paper, we present the optimized software implementation on the ultra-light symmetric cryptography algorithm, HIGHT.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.9
• /
• pp.1236-1243
• /
• 2014

Genetics is important for breeding and selection of horses but there is a lack of well-established horse-related browsers or databases. In order to better understand horses, more variants and other integrated information are needed. Thus, we construct a horse genomic variants database including expression and other information. Horse Single Nucleotide Polymorphism and Expression Database (HSDB) (http://snugenome2.snu.ac.kr/HSDB) provides the number of unexplored genomic variants still remaining to be identified in the horse genome including rare variants by using population genome sequences of eighteen horses and RNA-seq of four horses. The identified single nucleotide polymorphisms (SNPs) were confirmed by comparing them with SNP chip data and variants of RNA-seq, which showed a concordance level of 99.02% and 96.6%, respectively. Moreover, the database provides the genomic variants with their corresponding transcriptional profiles from the same individuals to help understand the functional aspects of these variants. The database will contribute to genetic improvement and breeding strategies of Thoroughbreds.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.3
• /
• pp.23-30
• /
• 2007

RFID it reads information which is it writes, the semiconductor chip for and the radio frequency system which uses the hazard antenna it has built-in transmission of information it talks. Formation which is transmitted like this collection and America which it filtrates wey the RFID search service back to inform the location of the server which has commodity information which relates with an object past record server. The hazard where measurement analysis result the leader for electronic interference does not occur consequently together from with verification test the power level which is received from the antenna grade where it stands must maintain minimum -55dBm and the electronic interference will not occur with the fact that, antenna and reel his recognition distance the maximum 7m until the recognition which is possible but smooth hazard it must stand and and with the fact that it will do from within and and and 3-4m it must be used Jig it is thought.