• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.9
• /
• pp.1309-1316
• /
• 2017

As penetration level of Distributed Generations (DGs) on weak distribution networks gets higher, voltage rise problem can often occur due to reverse power which is not expected in conventional distribution networks. It, however, cannot be effectively solved by using conventional voltage regulating devices such as On-Load Tap Changers (OLTCs), Step Voltage Regulators (SVRs) because those do not consider the presence of DGs when determining relevant setting parameter for voltage regulation. This paper presents a scheme for voltage regulation using coordinated control between OLTC and DGs which can actively participate in the regulation. The scheme decides which device should be operated first based on the characteristics of regulating devices, in order to prevent unnecessary operation of output changes of DG and excessive tap changing operation of OLTC. Computer simulations considering daily irradiation of PV and load curve are performed by using MATLAB Simulink and performance comparison between the presented scheme and conventional ones is also made. It can be concluded from simulation results that the scheme presented is very effective to regulate voltages in distribution networks with multiple DGs.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.3
• /
• pp.149-156
• /
• 2004

This paper deals with the effective protection method for the household electric appliances against lightning surges invading from the Power lines. Direct or induced lightning is the main cause of the breakdown of household electric appliance. The most effective protection method is to install SPDs(surge protective devices) at household electric appliances. If SPDs were not installed at most household electric appliances, it is necessary to install SPDs on the mains. Therefore the propagation aspect and protection methods of lighting surges coming into household electric appliances through the mains was experimentally investigated. The in actual-sized test circuits results of protection method for 8 household electric appliances including computer monitors and TV set could be summarized as follows: The breakdown characteristics of household electric appliances from lightning surges were significantly changed with the their input impedance. Namely, the types of input impedance are classified into infinite, resistive or inductive impedances. Especially, the monitor for computer with inductive input impedance from lightning surges was relatively weak against lightning surges. It was confirmed that the self inductance of branch circuits on the mains have protection effect for household electric appliances against lightning surges invading from the power lines. Also the varistors installed at cabinet panel or circuit-breaker were more effective than multi-tap outlet with varistors. When installed varistors in cabinet panel and multi-tap outlet together, the surge protection effect is much more excellent in technical and economical aspects.

• Journal of the Korean Society for Railway
• /
• v.19 no.2
• /
• pp.159-169
• /
• 2016

The current railway control system in Korea is comprised of signaling, electric rail power, communication, and maintenance systems that are independent of each other. Further, these systems have different mediums and protocols for transmitting the field equipment data to the central control system. The Safety Supervision System has as its purpose the collecting of safety-related data from each system to predict and prevent accidents, this system utilizes standard protocol. Safety-related data need to be collected from field data transmission devices of the existing control system, the data should be collected without affecting the communication of the existing system. In this study, sniffing skill, which is typically used for network traffic monitoring or security, is used to collect data. The problems arising from the use of sniffing devices are noted, and the Packet Conversion Node is proposed as a solution to the problems. Further, functional and performance testing were completed for the prototype, and the software architecture and packet conversion process were verified.

• The Journal of Engineering Geology
• /
• v.19 no.4
• /
• pp.433-439
• /
• 2009

The compressed packer device is designed to improve the underground contamination prevention facilities of ground water wells. As for the device, the installation is simple because of the safety lock device and the compression of the casing are simple the installation is simple. There is no leakage of ground water because the pressure resistance with $4.5\;kg/cm^2$ makes it equipped with the watertightness The single casing is installed and the reaming for grouting is possible with 300 mm excavation so that installation cost can be saved. Silicon rubber is used for the compressed packer so that the extension rate is 590%. In terms of environmental pollution, it is an environmental friendly product which does not contain harmful ingredients such as Pb, Cd, and phenol. below the standard or undetectable level Furthermore, the installation costs are 35 to 62% or lower than the conventional grouting construction method and are 87% or lower than the expansion packer construction method, the new environmental technology No.47 Also, the device is designed to meet the relevant regulations such as Rules on Preserving the Ground Water Quality, The Standard on Jeju Island Ground Water Development and Facility Installation and Management, and The Plan and Guideline on Operating and Managing the Small-Scale Tap Water Facilities of Ministry of Environment and Ministry of Food, Agriculture, Forestry and Fisheries.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.4
• /
• pp.549-556
• /
• 2016

CVR is a technique for reducing power consumption by reducing the voltage of the system and many demonstrations and studies have been conducted in the past. Recently, SCADA-based or AMI-based VVC have been developed and the CVR is used as an important operation mode. Using a variety of instruments, CVR determines the optimal VVC control references by closed loop control. In this paper, we implemented RTDS-MATLAB integrated simulation environment for development and verification of CVR control algorithm based on voltage measurement. The voltage control device of distribution system was modeled using RTDS and MATLAB has constructed a controller that can measure and control the voltage of the simulation system of RTDS. After the capacitor, which is a reactive power control device, flattens the voltage of the system, the control algorithm reduces the voltage of the system by tap control of the OLTC based on the flatten voltage. The proposed system was verified by simulations.

• Journal of the Institute of Convergence Signal Processing
• /
• v.5 no.4
• /
• pp.333-337
• /
• 2004

This paper describe a design of 5GHz OFDM baseband chip for IEEE 802.11a wireless LAN. The proposed device is consists of transmitter and receiver within a single FPGA chip. We applied single tap equalizer that use Normalized LMS algorithm to remove ISI that happen at high speed data transmission. And also, we used carrier wave frequency offset algorithm that use training symbol to remove ICI. The simulation results show the correct transmission without errors the between transmitter and receiver And we can remarkably reduce the number of register through the synthesized circuits by using DSP block and EMB(Embedded Memory Block). The target device for implementation of the synthesized circuits is Altera Stratix EPIS25FC672 FPGA and design platform is VHDL.

• Journal of Korea Multimedia Society
• /
• v.19 no.2
• /
• pp.189-199
• /
• 2016

Many implantable hearing aids are being developed as alternatives to conventional hearing aids which has inconveniences for use and social stigma that make hearing-impaired people avoid to wear it. Particularly, the fully-implantable middle ear hearing devices (F-IMEHD) are being actively studied for mixed or sensorineural hearing impaired people. In development of F-IMEHD, the most difficult problem is improving the performance of implantable microphone. Recently, Cho et al. have studied the tympanic membrane installed microphone which has better sensitivity and is easier to operate on patient than the microphone implanted under the skin. But, it may cause howling problem due to the feedback signal via oval window and ossicle chain from the transducer on round window in the middle ear cavity, therefore, a feedback canceller is necessary. In this paper, we designed NLMS (normalized least mean square) adaptive feedback canceller for F-IMEHD with tympanic membrane installed microphone and a transducer implemented at round window, and computer simulation was performed to verify its operation. The designed adaptive feedback canceller has a delay filter, a 64 point FIR fixed filter and a 8-tap adaptive FIR filter. Computer simulation of the feedback path is modeled by using the data obtained through human cadaver experiment.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.770-777
• /
• 2009

We have developed a fully functional reconfigurable optical add-drop multiplexer (ROADM) switch module using a polymer integrated photonic lightwave circuit technology. The polymer variable optical attenuator (VOA) array and digital optical switch array are integrated into one polymer PLC chip and packaged to form a 10-channel VOA integrated optical switch module. Four of these optical switch modules are used in the ROADM switch module to execute 40-channel switching and power equalization. As a wavelength division multiplexer (WDM) filter device, two C-band 40-channel athermal arrayed waveguide grating WDMs are used in the ROADM module. Optical power monitoring of each channel is carried out using a 5% tap PD. A controller and firmware having the functions of a 40-channel switch and VOA control, optical power monitoring, as well as TEC temperature control, and data communication interfaces are also developed in this study.

• Journal of Digital Convergence
• /
• v.14 no.3
• /
• pp.235-241
• /
• 2016

Among recent issues emerging in the areas related to the society, health has received the most attention. In this paper, for a patient unable to do self-care because of worsened diseases, a biological information transfer method is proposed by which the disease information can be securely managed, by attaching an implantable device into the body. Our method object of the invention is to prevent a third party from illegally intercepting and interfering with the biological information attached to the insertion device in the body. In the proposed technique to improve the safety of the patient between the hospital and physician by assigning each code to the biometric information of the patient in order to prevent a third party tapping and interfering. In addition, our method is assigned a code necessary for encoding in advance to confirm the biological information between the patient and the hospital (doctor) in a manner dividing the bio-information code. In particular, the proposed technique makes a third party unable to illegally tap or interfere in, by previously generating a code used for encoding so that it can be stored in the database of the hospital, which not only decreased hospital care time to 6.9%, but also increased work efficiency rate up to 12.7%.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.184-193
• /
• 2012

In this paper, a 5-bit 2-GS/s 2-way time interleaved pipeline ADC for high-speed serial link receiver is demonstrated. Implemented as a current-mode amplifier, the stage ADC simultaneously processes the tracking and residue amplification to achieve higher sampling rate. In addition, each stage incorporates a built-in 1-tap FIR equalizer, reducing inter-symbol-interference (ISI）without an extra digital post-processing. The ADC is designed in a 110nm CMOS technology. It comsumes 91mW from a 1.2-V supply. The area excluding the memory block is $0.58{\times}0.42mm^2$. Simulation results show that when equalizer is enabled, the ADC achieves SNDR of 25.2dB and ENOB of 3.9bits at 2.0GS/s sample rate for a Nyquist input signal. When the equalizer is disengaged, SNDR is 26.0dB for 20MHz-1.0GHz input signal, and the ENOB of 4.0bits.