• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.72-75
• /
• 1994

In this paper, a novel method to figure out the relative residual stress distribution along the depth of silicon diaphragms is presented Cantilevers with various thickness are fabricated by the time controlled etching method using EPW as an etchant. The boron concentration along the depth of the cantilevers is obtained by the TSUPREM IV simulation, and the etching time to get the proper thickness is calculated. By measuring deflections of the p+ silicon cantilevers the stress profile along the depth of diaphragm is calculated. The obtained stress profile is reasonable and useful to expect the deflection of cantilevers and the buckling of diaphragms.

• 한국자기공명학회논문지
• /
• 제24권1호
• /
• pp.23-29
• /
• 2020

Mozart's music has been suggested to affect spatio-temporal reasoning of listeners, which has been called "Mozart effect". However, the effects of Mazart's music on human metabolism have not been known. We dissected Mozart's music into its compositional elements and studied their effects on metabolism of experimental animals. Mozart music significantly reduced cortisol level induced by stress. NMR metabolomic study revealed different urine metabolic profile according to the listening to Mozart's music. In addition, each element of music exhibited different metabolic profile. Functional MRI study also showed enhanced brain activity upon listening to Mozart's music. Taken together, Mozart's music seems to be related with brain activity, stress hormone and whole body metabolism.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.74-79
• /
• 2012

It depends on the joint configuration, dimensions and constraints of the joint whether the residual stress at the root of single-sided butt weld is tensile or not. Therefore, recommendation is generally made that high R ratio should be used in the fatigue test of welded joint in order to prevent excessively long life caused by compressive residual stress. In this research, the residual stress profile in butt weld joint was obtained through compliance method, using successive extension of a slot and measurement of the variation of strain during the slot extension. The residual stress profile was firstly assumed to be the linear summation of Legendre polynomials up to 9th order excluding 0th and 1st order. Strain variation on the surface was measured while the slot was being extended by cutting to find out the 8 unknown coefficients of each polynomial term. The cut was made by the electric discharge machine. It was concluded that the residual stress near the surface is positive valued, however, it turned into the negative value as soon as it passed through 2 or 3 mm of the depth.

• 한국정밀공학회지
• /
• 제28권5호
• /
• pp.632-637
• /
• 2011

A new tooth profile which is adjusted on the amount of addendum modification factor is proposed for reducing vibration and noise of gears. The transmission error of the new profile can be designed more uniformly than that of the standard involute profile. The basic concepts of tooth profile modification are to reduce the load in contact area and to find the appropriate profile modification factor for operation condition. In this study, gears were estimated to constructive safety of bending strength and contact strength durability by using ROMAX program, and were compared with results by design formula of AGMA standard.

• 대한기계학회논문집A
• /
• 제36권4호
• /
• pp.387-393
• /
• 2012

본 논문에서는 기존 랙-피니언 시스템의 랙 치형을 핀 또는 롤러로 대체한 롤러 랙 피니언 (RRP) 시스템의 표면피로 향상방안을 고찰하였다. 우선 전위계수(profile shift coefficient)를 고려하여 RRP 시스템의 캠 피니언(cam pinion)에 대한 엄밀 치형설계 방법 및 언더컷 방지 조건을 소개하였고, 이를 바탕으로 설계인자의 변화에 따른 하중 및 하중응력계수(load stress factor)의 변화를 검토하였다. 이를 통해 RRP 시스템의 표면 내구성을 향상시킬 수 있는 방안으로 전위계수의 증가가 효과적임을 알 수 있었다.

• 대한기계학회논문집A
• /
• 제35권11호
• /
• pp.1453-1459
• /
• 2011

외접기어의 어느 한쪽 기어를 핀 또는 롤러로 대체한 롤러 피니언 기어 (RPG) 시스템은 기어 치물림 시 미끄럼 접촉을 줄이고 구름운동을 증대시켜 기어 내구성을 향상시킬 수 있다. 우선 본 논문에서는 전위계수(profile shift coefficient)를 고려하여 RPG 시스템의 캠 기어(cam gear)의 엄밀 치형설계 방법 및 치 꼬임으로 인한 간섭 방지조건을 제시하였다. 또 기어구동에 있어 치면에서 발생되는 진동이나 소음의 원인이 되는 피팅(pitting) 발생수명을 고려하기 위해, 설계인자의 변화에 따른 Hertz 접촉응력 및 하중응력계수(load stress factor)의 변화를 검토하였다. 이를 통해 RPG 시스템의 내구성을 향상시킬 수 있는 방안으로 전위계수의 증가를 제안하였다.

• 동력기계공학회지
• /
• 제15권4호
• /
• pp.48-53
• /
• 2011

Upon reviewing recent trends for robots, it can be seen that robots are gradually being miniaturized. However, most commercially available speed reducers have limitations in terms of structure and vibration when applied to small robots. In this respect, a tooth profile manufactured using thin plates was designed using balls and data analyzed related to numerical and FEM analysis. The speed reducer was manufactured to check their performance. The manufactured thin plate type speed reducer imposes less compressive stress on its tooth profile and balls, which can greatly increase feasibility.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.42-47
• /
• 2012

Construction equipment is heavily loaded during normal operation. In recent years, there is a trend that lower gear noise levels are demanded for drivers to avoid annoyance and fatigue during operation. For articulated hauler's final drive, meshing transmission error(T.E.) is the excitation that leads the tonal noise known as gear whine, and radiated gear whine is also the dominant source of noise in the whole gearbox. This paper presents a method for the analysis of the tooth profile modification, and the prediction of transmission error under the loaded torques for the spur gear pair of the articulated hauler's final drive. And the transmission error, transmission error harmonics and contact stress are also calculated and compared before and after tooth modification under one torque. The simulation result shows that the transmission error and contact stress under the loads can be minimized by the appropriate tooth profile modification.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.422-427
• /
• 2000

Gear design carried in former type determined a few variables like module, pressure angle, helix angle. After investigating repeatedly results obtained through stress analysis and making a determination an optimal shape, but its design process was not only complex but also difficult to get a precise profile curve from operating by hand. In this study, rotating shape of gear profile curves were generated automatically with standard spur gear, equivalent helical gear, shifted gear & pinion by using developed program which is Auto_LISP language supported in Auto-CAD. Output tooth profile by using CAE program is applied as Preprocessor for stress analysis in each contact points. This program which can be determined rapidly an optimal shape of gear will be successfully supported for Small & Medium companies designing and manufacturing gears by using Auto-CAD.

• Structural Engineering and Mechanics
• /
• 제62권5호
• /
• pp.587-593
• /
• 2017

The objective of this analytical study is to calculate the elasto-plastic stresses of Functionally Graded (FG) hyperbolic disc subjected to uniform temperature. The material properties (elastic modulus, thermal expansion coefficient and yield strength) and the geometry (thickness) of the disc are assumed to vary radially with a power law function, but Poisson's ratio does not vary. FG disc material is assumed to be non-work hardening. Radial and tangential stresses are obtained for various thickness profile, temperature and material properties. The results indicate that thickness profile and volume fractions of constituent materials play very important role on the thermal stresses of the FG hyperbolic discs. It is seen that thermal stresses in a disc with variable thickness are lower than those with constant thickness at the same temperature. As a result of this, variations in the thickness profile increase the operation temperature. Moreover, thickness variation in the discs provides a significant weight reduction. A disc with lower rigidity at the inner surface according to the outer surface should be selected to obtain almost homogenous stress distribution and to increase resistance to temperature. So, discs, which have more rigid region at the outer surface, are more useful in terms of resistance to temperature.