• 센서학회지
• /
• 제31권4호
• /
• pp.271-277
• /
• 2022

We analyzed the effects of the interface trap on the output characteristics of an inversion mode n-channel GaN Schottky barrier (SB)-MOSFET based on the N_it distribution using TCAD simulation. As interface trap number density (N_it) increased, the threshold voltage increased while the drain current density decreased. Under N_it=5.0×10¹⁰ cm^-2 condition, the threshold voltage was 3.2 V for V_DS=1 V, and the drain current density reduced to 2.4 mA/mm relative to the non-trap condition. Regardless of the N_it distribution type, there was an increase in the subthreshold swing (SS) following an increase in N_it. Under U-shaped N_it distribution, it was confirmed that the SS varied depending on the gate voltage. The interface fixed charge (Q_f) caused an shift in the threshold voltage and increased the off-state current collectively with the surface trap. In summary, GaN SB-MOSFET can be a building block for high power UV optoelectronic circuit provided the surface state is significantly reduced.

• Journal of Electrical Engineering and Technology
• /
• 제12권6호
• /
• pp.2324-2332
• /
• 2017

This paper presents the electrical performances of novel AlGaSb/InGaAs heterojunction-based vertical-tunneling field-effect transistor (VTFET). The device performance was investigated in views of the on-state current ($I_{on}$), drain-induced barrier thinning (DIBT), and subthreshold swing (SS) as the gate length ($L_G$) was scaled down. The proposed TFET with a $L_G$ of 5 nm operated with an $I_{on}$ of $1.3mA/{\mu}m$, a DIBT of 40 mV/V, and an SS of 23 mV/dec at a drain voltage ($V_{DS}$) of 0.23 V. The proposed TFET provided approximately 25 times lower DIBT and 12 times smaller SS compared with the conventional $L_G$ of 5 nm TFET. The AlGaSb/InGaAs VTFET showed extremely high scalability and strong immunity against short-channel effects.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권5호
• /
• pp.615-624
• /
• 2014

In this paper, we explore the electrical properties and high-frequency performance of carbon nanotube field-effect transistors (CNTFETs), based on the non-equilibrium Green's functions (NEGF) solved self - consistently with Poisson's equations. The calculated results show that CNTFETs exhibit superior performance compared with graphene nanoribbon field-effect transistors (GNRFETs), such as better control ability of the gate on the channel, higher drive current with lower subthreshold leakage current, and lower subthreshold-swing (SS). Due to larger band-structure-limited velocity in CNTFETs, ballistic CNTFETs present better high-frequency performance limit than that of Si MOSFETs. The parameter effects of CNTFETs are also investigated. In addition, to enhance the immunity against short - channel effects (SCE), hetero - material - gate CNTFETs (HMG-CNTFETs) have been proposed, and we present a detailed numerical simulation to analyze the performances of scaling down, and conclude that HMG-CNTFETs can meet the ITRS'10 requirements better than CNTs.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.206.2-206.2
• /
• 2015

최근 비정질 산화물 반도체 thin film transistor(TFT)는 차세대 투명 디스플레이로 많은 관심을 받고 있으며 활발한 연구가 진행되고 있다. 산화물 반도체 TFT는 기존의 비정질 실리콘 반도체에 비하여 큰 on/off 전류비, 높은 이동도 그리고 낮은 구동전압으로 인하여 차세대 투명 디스플레이 산업에 적용 가능하다는 장점이 있다. 한편 기존의 sputter나 evaporator를 이용한 증착 방식은 우수한 막의 특성에도 불구하고 많은 시간과 제작비용이 든다는 단점을 가지고 있다. 따라서 본 연구에서는 별도의 고진공 시스템이 필요하지 않을 뿐만 아니라 대면적화에도 유리한 용액공정 방식을 이용하여 박막 트렌지스터를 제작하였으며 thermal 열처리와 microwave 열처리 방식에 따른 전기적 특성을 비교 및 분석하고 각 열처리 방식의 열처리 온도 및 조건을 최적화 하였다. 제작된 박막 트렌지스터는 p-type bulk silicon 위에 산화막이 100 nm 형성된 기판에 spin coater을 이용하여 Al-Zn-Sn-O 박막을 형성하였다. 연속해서 photolithography 공정과 BOE (30:1) 습식 식각 과정을 이용해 활성화 영역을 형성하여 소자를 제작하였다. 제작 된 소자는 Pseudo-MOS FET구조이며, 프로브 탐침을 증착 된 채널층 표면에 직접 접촉시켜 소스와 드레인 역할을 대체하여 동작시킬 수 있어 전기적 특성평가가 용이하다는 장점을 가지고 있다. 그 결과, microwave를 통해 열처리한 소자는 100oC 이하의 낮은 열처리 온도에도 불구하고 furnace를 이용하여 열처리한 소자와 비교하여 subthreshold swing(SS), Ion/off ratio, field-effectmobility 등이 개선되는 것을 확인하였다. 따라서, microwave 열처리 공정은 향후 저온 공정을 요구하는 MOSFET 제작 시의 훌륭한 대안으로 사용 될 것으로 기대된다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권2호
• /
• pp.163-168
• /
• 2014

Bottom gate thin-film transistors were fabricated using solution processed IGZO channel layers with various gallium composition ratios that were annealed on a hot plate. Increasing the gallium ratio from 0.1 to 0.6 induced a threshold voltage shift in the electrical characteristics, whereas the molar ratio of In:Zn was fixed to 1:1. Among the devices, the IGZO-TFTs with gallium ratios of 0.4 and 0.5 exhibited suitable switching characteristics with low off-current and low SS values. The IGZO-TFTs prepared from IGZO films with a gallium ratio of 0.4 showed a mobility, on/off current ratio, threshold voltage, and subthreshold swing value of $0.1135cm^2/V{\cdot}s$, ${\sim}10^6$, 0.8 V, and 0.69 V/dec, respectively. IGZO-TFTs annealed at $300^{\circ}C$, $350^{\circ}C$, and $400^{\circ}C$ were also fabricated. Annealing at lower temperatures induced a positive shift in the threshold voltage and produced inferior electrical properties.

• 한국전기전자재료학회논문지
• /
• 제24권9호
• /
• pp.693-696
• /
• 2011

Recently, amorphous oxide semiconductors (AOSs) based thin-film transistors (TFTs) have received considerable attention for application in the next generation displays industry. The research trends of AOSs based TFTs investigation have focused on the high device performance. The electrical properties of the TFTs are influenced by trap density. In particular, the threshold voltage ($V_{th}$) and subthreshold swing (SS) essentially depend on the semiconductor/gate-insulator interface trap. In this article, we investigated the effects of Ar plasma-treated $SiO_2$ insulator on the interfacial property and the device performances of amorphous indium gallium zinc oxide (a-IGZO) TFTs. We report on the improvement in interfacial characteristics between a-IGZO channel layer and gate insulator depending on Ar power in plasma process, since the change of treatment power could result in different plasma damage on the interface.

• 한국전기전자재료학회논문지
• /
• 제35권3호
• /
• pp.264-268
• /
• 2022

High pressure deuterium (HPD) annealing is an advancing technology for the fabrication of modern semiconductor devices. In this work, gate-enclosed FETs are fabricated on a silicon substrate as test vehicles. After a cycle for the HPD annealing, the device parameters such as threshold voltage (V_TH), subthreshold swing (SS), on-state current (I_ON), off-state current (I_OFF), and gate leakage (I_G) were measured and compared depending on the HPD. The HPD annealing can passivate the dangling bonds at Si-SiO₂ interfaces as well as eliminate the bulk trap in SiO₂. It can be concluded that adding the HPD annealing as a fabrication process is very effective in improving device reliability, performance, and variability.

• 한국전기전자재료학회논문지
• /
• 제37권1호
• /
• pp.43-47
• /
• 2024

The size of semiconductor devices has been scaled down to improve packing density and output performance. However, there is uncontrollable spreading of the dopants that comprise the well, punch-stop, and channel-stop when using high-temperature annealing processes, such as rapid thermal annealing (RTA). In this context, low-temperature deuterium annealing (LTDA) performed at a low temperature of 300℃ is proposed to reduce the thermal budget during CMOS fabrication. The LTDA effectively eliminates the interface trap in the gate dielectric layer, thereby improving the electrical characteristics of devices, such as threshold voltage (V_TH), subthreshold swing (SS), on-state current (I_ON), and off-state current (I_OFF). Moreover, the LTDA is perfectly compatible with CMOS processes.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권3호
• /
• pp.134-140
• /
• 2002

Deep submicron NMOSFETs with elevated source/drain can be fabricated using self-aligned selective epitaxial growth(SEG) of silicon for enhanced device characteristics with shallow junction compared to conventional MOSFETs. Shallow junctions, especially with the heartily-doped S/D residing in the elevated layer, give hotter immunity to Yt roll off, drain-induced-barrier-lowering (DIBL), subthreshold swing (SS), punch-through, and hot carrier effects. In this paper, the characteristics of both deep submicron elevated source/drain NMOSFETs and conventional NMOSFETs were investigated by using TSUPREM-4 and MEDICI simulators, and then the results were compared. It was observed from the simulation results that deep submicron elevated S/D NMOSFETs having shallower junction depth resulted in reduced short channel effects, such as DIBL, SS, and hot carrier effects than conventional NMOSFETs. The saturation current, Idsat, of the elevated S/D NMOSFETs was higher than conventional NMOSFETs with identical device dimensions due to smaller sheet resistance in source/drain regions. However, the gate-to-drain capacitance increased in the elevated S/D MOSFETs compared with the conventional NMOSFETs because of increasing overlap area. Therefore, it is concluded that elevated S/D MOSFETs may result in better device characteristics including current drivability than conventional NMOSFETs, but there exists trade-off between device characteristics and fate-to-drain capacitance.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.199-199
• /
• 2010

최근 평판 디스플레이 산업의 발전에 따라 능동행렬 액정 표시 소자 (AMOLED : Active Matrix Organic Liquid Crystral Display) 가 차세대 디스플레이 분야에서 각광을 받고있다. 기존의 TFT-LCD에 사용되는 a-Si:H는 균일도가 좋지만 전기적인 스트레스에 의해 쉽게 열화되고 낮은 이동도는 갖는 단점이 있으며, ELA (Eximer Laser Annealing) 결정화 poly-Si은 전기적인 특성은 좋지만 uniformity가 떨어지는 단점을 가지고 있어서 AMOLED 및 대면적 디스플레이에 적용하기 어렵다. 따라서 a-Si:H TFT보다 좋은 전기적인 특성을 보이며 ELA 결정화 poly-Si TFT보다 좋은 uniformity를 갖는 SPC (Solid Phase Crystallization) poly-Si TFT가 주목을 받고있다. 본 연구에서는 차세대 디스플레이 적용을 위해서 glass 기판위에 증착된 a-Si을 SPC 로 결정화 시킨 후 TFT를 제작하고 평가하였다. 또한 TFT 형성시에 저온공정을 실현하기 위해서 소스/드레인 영역에 실리사이드를 형성시켰다. 소자 제작시의 최고온도는 $500^{\circ}C$ 이하에서 공정을 진행하는 저온 공정을 실현하였다. Glass 기판위에 a-Si이 80 nm 증착된 기판을 퍼니스에서 24시간 동안 N2 분위기로 약 $600^{\circ}C$ 에서 결정화를 진행하였다. 노광공정을 통하여 Active 영역을 형성시키고 E-beam evaporator를 이용하여 약 70 nm 의 Pt를 증착시킨 후, 소스와 드레인 영역의 실리사이드 형성은 N2 분위기에서 $450^{\circ}C$, $500^{\circ}C$, $550^{\circ}C$에서 열처리를 통하여 형성하였다. 게이트 절연막은 스퍼터링을 이용하여 SiO2를 약 15 nm 의 두께로 증착하였다. 게이트 전극의 형성을 위하여 E-beam evaporator 을 이용하여 약 150 nm 두께의 알루미늄을 증착하고 노광공정을 통하여 게이트 영역을 형성 후 에 $450^{\circ}C$, H2/N2 분위기에서 약 30분 동안 forming gas annealing (FGA)을 실시하였다. 제작된 소자는 실리사이드 형성 온도에 따라서 각각 다른 특성을 보였으며 $450^{\circ}C$에서 실리사이드를 형성시킨 소자는 on currnet와 SS (Subthreshold Swing)이 가장 낮은것을 확인하였다. $500^{\circ}C$와 $550^{\circ}C$에서 실리사이드를 형성시킨 소자는 거의 동일한 on current와 SS값을 나타냈다. 이로써 glass 기판위의 SB-TFT 제작 시 실리사이드 형성의 최적온도는 $500^{\circ}C$로 생각되어 진다. 위의 결과를 토대로 본 연구에서는 SPC 결정화 방법을 이용하여 SB-TFT를 성공적으로 제작 및 평가하였고, 차세대 디스플레이에 적용할 경우 우수한 특성이 기대된다.