Matsushige T.;Ishitobi M.;Nakaoka M.;Bessyo D.;Yamashita H.;Omori H.;Terai H.
Proceedings of the KIPE Conference
/
2001.10a
/
pp.484-488
/
2001
The grid voltage of commercial utility power source hi Japan and USA is 100rms, but in China and European countries, it is 200rms. In recent years, In Japan 200Vrms out putted single phase three wire system begins to be used for high power applications. In 100Vrms utility AC power applications and systems, an active voltage clamped quasi-resonant Inverter circuit topology using IGBTs has been effectively used so far for the consumer microwave oven. In this paper, presented is a half bridge type voltage-clamped high-frequency Inverter type AC-DC converter using which is designed for consumer magnetron drive used as the consumer microwave oven in 200V utility AC power system. This zero voltage soft switching Inverter can use the same power rated switching semiconductor devices and three-winding high frequency transformer as those of the active voltage clamped quasi-resonant Inverter using the IGBTs that has already been used for 100V utility AC power source. The operating performances of the voltage source single ended push pull type Inverter are evaluated and discussed for consumer microwave oven. The harmonic line current components In the utility AC power side of the AC-DC power converter operating at ZVSPWM strategy reduced and improved on the basis of sine wave like pulse frequency modulation and sine wave like pulse width modulation for the utility AC voltage source.
This experiment was planned to study the mating behavior of the fall webworm. Hyphantria cunea Drury. In this experiment. observations on mating behavior of the fall webworm were based on the time of moth emergence, time of mating activity, copulation period, mating frequency, and effect of moth ages on the mating ratio. Mating frequency was determined by visual observation and the number of spermatophores. The results obtained were as follows; 1) The moths started emerging at about 3 P. M. and ended at about 12 P. M. The peak of moth emergence was between 7 and 8 P. M. Total ratio or the moths emerged between 7 and 8 P. M. was 42. 1 for female and 41.8 for male. 2) Mating activity was mostly confined to the period between 5 and 6 A. M. The average complation period was 12 hours (ranges between 7 and 17 hours). 3) The average ratio of single mating was $66.0\%$ for both sexes, and that of double. matings were $4.1\%$ for females and $5.4\%$ for males in laboratory test. The mating ratio of female moths collected from the field was $62.1\%$ for single mating. and 15.5" for doubles matings. These data indicated that single mating seemed to be most common. 4) Mating usually occured within four days after the emergence from the pupae. Mating ratio was greatly varied with the moth ages. The highest mating ratio was observed within 6 to 15 hours after moth emergence. Both sexes usually mated with the moths of the same ages.
The Journal of Korean Institute of Communications and Information Sciences
/
v.18
no.6
/
pp.854-862
/
1993
All of the CMOS analog and analog-digital systems have composed with several basic circuits, and among them, a important block, the amplifier part can affect the system's performance, Therefore, according to the uses in the system, the amplifier circuit have designed as various architectures (high-gain, low-noise, high-speed circuit, etc...). In this paper, we have proposed a new CMOS differential amplifier circuit. This circuit is differential to single ended input stage comprised of CMOS complementary gain circuits having internally biasing configurations. These architectures can be achieved the high gain and reduced the transistors for biasing. As a results of SPICE simulation with the standard $1.5{\mu}m$ processing parameter, the gain of the proposed circuit have a doubly value of the typical circuit's while maintaining other characteristics(phase margin, offset, etc...). And the proposed circuit is applicated in a simple CMOS comparator which has the settling time in 7nsec(CL=1pF) and the igh output swing $({\pm}4.5V)$.
Ji, Chang-Yoon;Kim, Tae-Ju;Lee, Seung-Ho;Kim, Young-Sik;Lee, Guem-San;Kim, Jung-Hoon;Choi, Goya;Ju, Young-Sung
The Journal of Korean Medicine
/
v.34
no.3
/
pp.1-12
/
2013
Objectives: This was study about identifying fine seed herbs that are highly mixed together: Celosiae Semen, Celoisae Cristatae Semen, Cuscutae Semen, Perillae Semen. Methods: In non-distinctive herbs through sensory test, we can find accurate discriminative points by using a stereoscope. As a result, a new discriminative key was completed. Results: We identified a comparison of herbs which are mixed up in distribution. 1) In the case of Celosiae Semen and Celoisae Cristatae Semen, Celoisae Cristatae Semen which is mixed up is bigger and more glossy and especially have the sunk umbilicus. 2) In the case of Cuscutae Semen and Perillae Semen, Perillae Semen is discriminated by characteristic morado netting surface and impression of fruit stalk in the single-ended. 3) In the case of Cuscutae Semen which is distributed in three species, we discriminated by beak shape, location of umbilicus and vomiting thread shape or not when put in water. (1) Cuscuta chinensis has a weak beaky shape, an umbilicus in center and is vomiting thread shape when put in water. (2) C. australis has very weak beaky shape, an umbilicus beneath and is vomiting thread shape when put in water. (3) C. japonica has clear beaky shape, an umbilicus beneath and is not vomiting thread shape when put in water. Conclusions: A stereoscope can be effectively used for identifying fine seed herbs hardly distinguishable by sensory tests.
The objective of this work was to study the effect of mixed culture solid substrate fermentation of C. tropicalis ZD-3 with A. niger ZD-8 on detoxification of cottonseed meal (CSM), and to investigate the effect of fermentation period, proportion of CSM in substrate, sodium carbonate, minerals and heat treatment on the reduction of free gossypol levels during mixed culture solid substrate fermentation of CSM. Experiment 1: Three groups of disinfected CSM substrate were incubated for 48 h after inoculation with either of the fungi C. tropicalis ZD-3, A. niger ZD-8 or mixed culture (C. tropicalis ZD-3 with A. niger ZD-8). One non-inoculated group was used as the control. Levels of initial and final free gossypol (FG), CP and in vitro CP digestibility were assayed. The results indicated that mixed culture fermentation was far more effective than single strain fermentation, which not only had higher detoxification rate, but also had higher CP content and in vitro digestibility. Experiment 2: CSM substrates were treated according to experimental variables including fermentation period, proportion of CSM in substrate, sodium carbonate, minerals and heat treatment, Then, the treated CSM substrates were inoculated with mixed culture (C. tropicalis ZD-3 with A. niger ZD-8) and incubated at $30^{\circ}C$ for 36 h in a 95% relative humidity chamber. After fermentation ended, FG and CP content of fermented CSM substrate was assayed. The results showed that the appropriate fermentation period was 36 h, and the optimal proportion of CSM in substrate was 70%. Addition of sodium carbonate to CSM substrate was beneficial for fermentative detoxification. Heat treatment could facilitate fermentative detoxification, and supplementation with minerals was instrumental in reducing gossypol levels during mixed culture solid substrate fermentation of CSM.
We developed a 0.1-㎛ metamorphic high electron mobility transistor and fabricated a W-band monolithic microwave integrated circuit chipset with our in-house technology to verify the performance and usability of the developed technology. The DC characteristics were a drain current density of 747 mA/mm and a maximum transconductance of 1.354 S/mm; the RF characteristics were a cutoff frequency of 210 GHz and a maximum oscillation frequency of 252 GHz. A frequency multiplier was developed to increase the frequency of the input signal. The fabricated multiplier showed high output values (more than 0 dBm) in the 94 GHz-108 GHz band and achieved excellent spurious suppression. A low-noise amplifier (LNA) with a four-stage single-ended architecture using a common-source stage was also developed. This LNA achieved a gain of 20 dB in a band between 83 GHz and 110 GHz and a noise figure lower than 3.8 dB with a frequency of 94 GHz. A W-band image-rejection mixer (IRM) with an external off-chip coupler was also designed. The IRM provided a conversion gain of 13 dB-17 dB for RF frequencies of 80 GHz-110 GHz and image-rejection ratios of 17 dB-19 dB for RF frequencies of 93 GHz-100 GHz.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.48
no.11
/
pp.48-56
/
2011
Novel class-A bipolar current conveyor($CCII{\pm}$) with differential current output and its application to output current controllable CCII+ for electronic tuning systems are designed. The $CCII{\pm}$ is consists of conventional CCII+ and complementary cross current sources. The CCII+ with controllable the output current consists of the $CCII{\pm}$ and a current gain amplifier with single-ended current output. The simulation result shows that the $CCII{\pm}$ has current input impedance of $1.9{\Omega}$ and a good linearity for voltage and current follower. The proposed CCII+ has 3-dB cutoff frequency of 10MHz for the range over bias control current $100{\mu}A$ to 10mA. The range of output current control is four decade. The power dissipation of the CCII+ is 4.5mW at supply voltage of ${\pm}2.5V$.
Journal of the Korea Institute of Information and Communication Engineering
/
v.20
no.9
/
pp.1633-1640
/
2016
In this paper, we propose a open-ended rectangular microstirp patch antenna with fork-shaped feeding structure. This antenna extends the effective bandwidth by transforming single or multi resonant frequency and is designed planar monopole structure with microstrip line to satisfy the WLAN bands (2.4 - 2.484, 5.15 - 5.35, 5.25-5.825 GHz). The substrate is printed in 0.8 mm thickness on an FR-4 board. A commercial 3D simulation tool was used to analyze surface current and electromagnetic field distribution in order to analyze the operation mode and reconfiguration principle of antenna. According to the lengths of individual patches, simulated reflection loss was compared to obtain optimized values. When it was designed with the optimized values, it satisfied WLAN bands (2.380 - 2.710, 4.900 - 5.950 GHz), if the switch is off, and 2.4 WLAN band (2.380 - 2.710 GHz). From the fabricated and measured results, measured results of return loss, gain and radiation patterns characteristics displayed for operating bands.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.38
no.11
/
pp.836-845
/
2001
A Novel fully-differential bipolar current subtracter(FCS) and its application to current controlled current amplifier(CCCA) for high-accuracy current-mode signal processing were designed. To obtain full-differential current output, the FCS was symmetrically composed of two current follower with low current-input impedance. The CCCA to control output current by the bias current was consisted of the subtracter and a current gain amplifier(CGA) with single-ended current output.. The simulation result shows that the FCS has current-input impedance of 5 Ω and a good linearity. The CCCA has 3-dB cutoff frequency of 20 MHz for the range over bias current 100 $\mu$A to 20 mA. The power dissipation of the FCS and CCCA are 1.8 mW and 3 mW, respectively.
Kim, Ji-Yeon;Lee, Dong-Heon;Chun, Sang-Hyun;Yoo, Ho-Joon;Kim, Jong-Heon
The Journal of Korean Institute of Electromagnetic Engineering and Science
/
v.20
no.1
/
pp.1-11
/
2009
In this paper, a new 1 kW power amplifier with high efficiency and high stability in a RF generator is designed and fabricated for plasma applications. The efficiency of power amplifier is improved by using class-E amplifier that consists of one push-pull MOSFET and high current drive IC instead of class-C amplifier composed of several single ended MOSFET. Switchable damper that allows selecting three different modes of amplifiers for considering efficiency and stability is added into the amplifier for plasma applications. Stable region of an early electronic discharge section is extended to VSWR of 4.5:1 compared to conventional VSWR of 3.8:1 through using switchable damper. The dimension of the amplifier is also reduced to 30 % of conventional amplifier. The 80 % efficiency of power amplifier with switchable damper is obtained the output power of 1 kW in operating frequency of 13.56 MHz. In comparison of conventional power amplifier for plasma applications, 13 % efficiency is improved.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.